D1265 EN Installation Guide Touchscreen Keypad
D1265 Installation Guide 1.0 Introduction Contents 1.0 Introduction...3 1.1 Overview...3 1.2 Graphical Buttons...3 1.3 Audible Tones...4 1.4 Supervision...4 1.5 Tamper Switch...4 2.0 Installation...5 3.0 Setup Menu...6 3.1 Set the Keypad SDI Bus Address...6 3.2 Adjust the Keypad Volume and Display...6 3.2.1 Adjust the Keypad Volume...6 3.2.2 Turn the Button Click On or Off...6 3.2.3 Adjust the Display Brightness...7 3.2.4 Screen On Time...7 3.3 Saving Changes and Exiting the Setup Menu...7 4.0 RPS Configuration...7 4.1 Start RPS...7 4.2 Enable the Keypad...7 4.3 Enter Security Company Information...8 4.4 Update and Reset the Control Panel...9 5.0 Specifications...9 FCC This device can be expected to comply with Part 15 of the FCC Rules provided it is assembled in exact accordance with the instructions provided with this kit. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. 2 Bosch Security Systems, Inc. 11/11 F01U169129-05
. 1.0 Introduction 1.1 Overview The D1265 Touchscreen Keypad is an SDI bus device and it is compatible with the Bosch GV2, GV3, and later, families of control panels: D9412GV3, D7412GV3, and D7212GV3 D9412GV2, D7412GV2, and D7212GV2 Figure 1: 1 1 - Touchscreen area 2 - Speaker D1265 Touchscreen Keypad 2 D1265 Installation Guide 1.0 Introduction 1.2 Graphical Buttons Refer to Table 1 for descriptions of the D1265 s graphical buttons. Table 1: Graphical Button to Graphical Button Descriptions Description Press this button to see onscreen help instructions. Press this button in combination with one or two numeric buttons to perform a function. Press this button to complete the entry of your passcode at the keypad. Press these buttons to enter numeric values. Press this button to see a list of available functions. Press this button to scroll back through the function menu. Press this button to scroll forward through the function menu. Press this button to exit the function menu. The control panel supplies all power and data requirements for the D1265 through a four-wire connection. To determine if you need an additional power supply, refer to the Current Rating Chart for Standby Battery Calculations provided in the approved applications compliance guide for the specific control panel used with the D1265. Bosch Security Systems, Inc. 11/11 F01U169129-05 3
D1265 Installation Guide 1.0 Introduction 1.3 Audible Tones The D1265 Touchscreen Keypad has a built-in speaker that produces several distinct warning tones. You cannot connect external annunciation devices to the D1265. Anytime the D1265 emits an audible tone, the keypad illuminates. Silence the audible tones in Table 2 by entering a programmed passcode with the appropriate authority, or [COMMAND] + [4] unless otherwise noted. Table 2: Tone Fire Signal Burglary Signal Entrance Warning Exit Warning Invalid Button Buzz Keypad Encoding Tone Trouble Buzzer Watch Tone Audible Tones Description When an area is in fire alarm, the keypad emits a pulsed, high-pitched bell tone. When an area is in alarm, the keypad emits a steady, high-pitched bell tone. The keypad emits an intermittent beep tone during entry delay periods to remind the user to disarm the area. The keypad emits an intermittent beep tone during exit delay. When an invalid button, or sequence of buttons, is pressed, the keypad emits a flat buzz tone. The keypad emits a muted beep tone as each button is pressed to indicate that the entry was accepted. To disable this feature, refer to Section 3.2.2 Turn the Button Click On or Off on page 6. When a trouble event occurs, such as a service alert, the keypad emits a two-tone warble until you enter [COMMAND] + [4]. When you activate the Watch feature ([COMMAND] + [6]), a single clean tweedle tone alerts the user anytime a watch point is faulted. This option is programmable by point. To disable the Watch Feature, press [COMMAND] + [6] again. 1.4 Supervision You can program the control panel to send messages identifying the supervised keypad to the central station receiver. To supervise a keypad, refer to the program entry guide for your control panel. If a keypad loses communication with the control panel for more than 15 sec, the keypad buzzes and the Call for Service message appears. Other keypads connected to the system show Service Keypad. The control panel sends a serial device trouble report to the receiver. The keypad shows SDI FAILURE # if the Modem IIIa 2 communication format is used. For more information, refer to the D6600 Computer Interface Manual (P/N: 4998122703). 1.5 Tamper Switch When the tamper switch is activated, the keypad sends a message to the control panel. Regardless of whether the control panel supervises the keypad or not, if the keypad s tamper switch activates, the Call for Service message appears. The tamper switch activates when someone or something pulls the D1265 away from a flat surface. Refer to Figure 4 and Figure 5 on page 5 for the location of the enclosure knockout and the tamper switch. 4 Bosch Security Systems, Inc. 11/11 F01U169129-05
. 2.0 Installation The D1265 Touchscreen Keypad is a low-profile, surface-mounted unit. Avoid installing the D1265 in direct sunlight. Direct sunlight can interfere with display screen visibility, and can damage internal components. Avoid installing the D1265 in wet or moist locations. 1. Unlock the keypad by turning the lock counter-clockwise. Refer to Figure 2. Figure 4: 1 2 D1265 Installation Guide 2.0 Installation D1265 Keypad (Back view) Figure 2: Unlock the Keypad 1 - Tamper switch 2 - Terminal block connectors 3. Use the base as a template to mark the desired mounting surface. Refer to Figure 5 for mounting hole and wiring locations. Figure 5: D1265 Base 5 2 3 1 1 9 6 7 8 2. Hold the keypad by the base in one hand. With the other hand, gently push down on the keypad to remove it from the base. Refer to Figure 3. 5 6 4 5 9 Figure 3: Remove the Keypad from the Base 10 1 1 5 3 2 1 - Wall mount holes 2 - Single gang box holes 3 - Dual gang box holes 4 - Wire opening 5 - Alternate wire openings 6 - Wire channel 7 - Tamper switch knockout 8 - Bubble level 9 - Wire tie posts 10 - Terminal block Bosch Security Systems, Inc. 11/11 F01U169129-05 5
D1265 Installation Guide 3.0 Setup Menu 4. Pull the wiring through the desired wire opening in the base. 5. Use the appropriate mounting hardware (not supplied) to mount the base to the desired mounting surface. 6. Connect the keypad to the control panel as shown in Figure 6. Figure 6: Wire Connections 1 3.0 Setup Menu To enter the setup menu, press and hold the 0 button for at least 5 sec. The setup menu opens. Use the D1265 s setup menu to: Set the keypad s SDI Bus address Adjust the keypad volume and display brightness Turn the button click tone on or off Set the screen on-time Figure 7: D1265 Setup Menu RYGB 2 EVICE CONNECTIONS POWER + 32 DATA BUS A 31 DATA BUS B 30 COMMON 29 1 - D1265 Base 2 - Control panel peripheral device terminals 3 - POWER + to R wire connection 4 - DATA BUS A to Y wire connection 5 - DATA BUS B to G wire connection 6 - COMMON + to B wire connection 7. Reconnect the keypad to the base by sliding the keypad onto the base (reverse of Step 2). The keypad automatically locks onto the base. 8. Apply power to the system. 3 5 6 4 3.1 Set the Keypad SDI Bus Address To set the keypad s SDI Bus address, press the Up or Down arrow buttons until you reach the desired address (1 to 32). Each SDI bus device must have a unique address assigned to it. 3.2 Adjust the Keypad Volume and Display 3.2.1 Adjust the Keypad Volume To adjust the keypad s volume, press the Up or Down arrow buttons until you reach the desired level (0 = silent; 10 = loudest). This setting only applies to normal interaction with the keypad. Alarms always sound at the loudest volume setting. 3.2.2 Turn the Button Click On or Off To turn the button click tone on, press the Up arrow button. To turn the button click tone off, press the Down arrow button. 6 Bosch Security Systems, Inc. 11/11 F01U169129-05
. 3.2.3 Adjust the Display Brightness To adjust the keypad s display brightness, press the Up or Down arrow buttons until you reach the desired level (1 = darkest; 15 = brightest). 3.2.4 Screen On Time To adjust how long the keypad display stays on, press the Up or Down arrow buttons until you reach the desired time (1-15 min). If there is no keypad activity within the specified duration, the keypad goes into sleep mode. In this mode, the keypad display is dark. 3.3 Saving Changes and Exiting the Setup Menu When you are done making changes in the setup menu, press the Save button. To exit the setup menu, press the Back button. The keypad returns to the normal display. 4.0 RPS Configuration To configure the D1265, RPS version 5.12 or later is required. 4.1 Start RPS For complete instructions on using RPS to program a control panel, refer to the RPS Online Help and the specific control panel s online help file in RPS. 1. Start RPS. 2. Enter a valid username and password. 3. Open the desired control panel account. D1265 Installation Guide 4.0 RPS Configuration 4.2 Enable the Keypad 1. In the Program Record Sheet, locate the section called COMMAND CENTER (GV2MAIN). This section is named the same whether you are in a GV3 or a GV2 account. Figure 8: RPS: COMMAND CENTER (GV2MAIN) 2. In the Cmd Ctr Assignments pane, locate Enhanced Command Center. Figure 9: RPS: Enhanced Command Center 3. Change Enhanced Command Center for the desired keypad address to Yes. Figure 8 uses CC Address 1 as an example. Bosch Security Systems, Inc. 11/11 F01U169129-05 7
D1265 Installation Guide 4.0 RPS Configuration 4. In the Program Record Sheet, go to USER INTERFACE (GV2MAIN)>Command Center Functions. Set Display Revision Command 59 to E (Enabled). This setting allows the configuration changes for the D1265 to take effect. Figure 10: RPS: Display Revision CMD 59 2. Under Passcodes & Authority Levels: Select Users 201-249 for the D9412GV3 and D9412GV2 Select Users 51-99 for the D7412GV3, D7412GV2, D7212GV3, and D7212GV2 Figure 12: RPS: Passcodes & Authority Levels 4.3 Enter Security Company Information Use the following steps to enter your security company s name and phone number. The users see this information when they press the Help? button on the D1265, and then press the Security Co. Info. button. 1. In RPS, in the Program Record Sheet pane, expand the PASSCODES (RADXUSR1/RADXUSR2) section. Refer to Figure 11 (the D9412GV3 is used as an example). 3. Scroll through the list of users to User 249 for the D9412GV3 and D9412GV2. Scroll to User 99 for the D7412GV3, D7412GV2, D7212GV3, and D7212GV2. 4. Double-click the cell for User 249 or User 99. The User Name dialog opens. Figure 13: RPS: User Name Dialog Figure 11: RPS: PASSCODES (RADXUSR1/RADXUSR2) 8 Bosch Security Systems, Inc. 11/11 F01U169129-05
. 5. Enter the security company s phone number and click OK. The new number appears in the appropriate User cell. Figure 14: RPS: User Name Change 4.4 Update and Reset the Control Panel 1. When you are done with RPS, click the Save button. If RPS is not already online with the control panel, start a communication session and send the programming changes to the control panel. 2. When you are ready to end the online session, click the Disconnect button and check the Rest Panel box on the End Session dialog for the programming changes to take effect. D1265 Installation Guide 5.0 Specifications 5.0 Specifications Table 3: Nominal Voltage Wiring D1265 Specifications 12 VDC Maximum resistance 11 Ω Standby Current Idle: 135 ma Dimensions (H x W x D): Weight Environmental Operating Temperature Relative Humidity Enclosure Color Enclosure Material Max*: 300 ma 12.2 cm x 12.0 cm x 3.0 cm (4.8 in. x 4.7 in. x 1.2 in.) 0.24 kg (8.5 oz.) Intended for indoor use 0 C to +49 C (+32 F to +120 F) 85% + 2% @ +49 C (+120 F) Bosch White Plastic (ABS) * With speaker and display backlight at maximum. Figure 15: RPS End Session Dialog 3. To close RPS, click the X button in the upper right corner twice. Bosch Security Systems, Inc. 11/11 F01U169129-05 9
Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450 USA www.boschsecurity.com Bosch Security Systems, Inc., 2010