1
Main Advanced H/W Monitor Boot Security Exit System Overview System Time System Date BIOS Version Processor Type Processor Speed Microcode Update : 40F32/62 L1 Cache Size : 256KB L2 Cache Size : 2048KB Total Memory DDRII1 DDRII2 DDRII3 DDRII4 [ 17:00:09] [Tue 02/26/2008] : A780FullDisplayPort P1.0 : AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ (64bit) : 2400MHz : 1024MB with 128MB shared memory Single-Channel Memory Mode : 1024MB/266MHz (DDRII533) :None :None :None Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. +- Change Field Tab Select Field Main Advanced H/W Monitor Boot Security Exit Advanced Settings Options for CPU WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration Enter Go to Sub Screen 2
Advanced CPU Configuration AM2 Boost Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) Spread Spectrum Boot Failure Guard Cool'n'Quiet Secure Virtual Machine [200] [100] If AUTO, multiplier and voltage will be left at the rated frequency/voltage. If Manual, multiplier and voltage will be set based on User Selection in Setup. Processor Maximum Frequency Processor Maximum Voltage Multiplier/Voltage Change Memory Clock Flexibility Option CAS Latency (CL) TRCD TRP x15.0 3000 MHz 1.400 V F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 3
Advanced CPU Configuration AM2 Boost Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) Spread Spectrum Boot Failure Guard Cool'n'Quiet Secure Virtual Machine [200] [100] If AUTO, multiplier and voltage will be left at the rated frequency/voltage. If Manual, multiplier and voltage will be set based on User Selection in Setup. Processor Maximum Frequency Processor Maximum Voltage Multiplier/Voltage Change Processor Frequency Processor Voltage Memory Clock Flexibility Option x15.0 3000 MHz 1.400 V [Manual] [x9.0 1800 MHz] [1.350 V] F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 4
5
6
Advanced Chipset Settings To set DRAM Voltage. OnBoard HD Audio Front Panel OnBoard LAN Onboard IEEE 1394 Primary Graphics Adapter Share Memory OnBoard HDMI HD Audio GFX Engine Clock Override Surround View CPU-NBLinkSpeed CPU-NBLinkWidth DRAM Voltage [PCI] + - Change Option 7
8
Advanced ACPI Settings Suspend To RAM Repost Video on STR Resume Away Mode Support Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On ACPI HPET Table [No] [Power Off] Select auto-detect or disable the STR feature. 9
Advanced IDE Configuration Onboard SATA Controller SATA Operation Mode IDE1 Master IDE1 Slave SATAII_1 SATAII_2 SATAII_3 SATAII_4 SATAII_5 SATAII_6 [non-raid] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] Configure onboard serial ATA controller. F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit Advanced IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. :Hard Disk :MAXTOR 6L080J4 :80.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-6 :Supported Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer Select the type of device connected to the system. 10
11
Advanced Advanced PCI / PnP Settings PCI Latency Timer PCI IDE BusMaster [32] ValueinunitsofPCI clocks for PCI device latency timer register. Advanced Floppy Configuration 1 Floppy A [1.44 MB 3 2 "] Select the type of floppy drive connected to the system. 12
Advanced Configure Super IO Chipset OnBoard Floppy Controller Serial Port Address Infrared Port Address [3F8 / IRQ4] Allow BIOS to Enable or Disable Floppy Controller. 13
Advanced USB Configuration USB Controller USB 2.0 Support Legacy USB Support [BIOS Setup Only] To enable or disable the onboard USB controllers. 14
Main Advanced H/W Monitor Boot Security Exit Hardware Health Event Monitoring CPU Temperature M / B Temperature : 37C/98F : 31C/87F CPU Fan Speed Chassis Fan Speed : 2833 RPM :N/A Vcore + 3.30V + 5.00V + 12.00V CPU Quiet Fan : 1.532 V : 3.129 V : 4.877 V : 11.741 V F1 F9 F10 ESC General Help Load Defaults Save and Exit Exit Main Advanced H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration Configure Settings during System Boot. 1st Boot Device 2nd Boot Device 3rd Boot Device 4th Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM-MAXTOR 6L08] [CD/DVD: SM-CD-ROM] [USB] Enter Go to Sub Screen 15
Boot Boot Settings Configuration Boot From Onboard LAN Bootup Num-Lock [On] To enable or disable the boot from network feature. + - Change Option Main Advanced H/W Monitor Boot Security Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Install or Change the password. Enter Change 16
Main Advanced H/W Monitro Boot Security Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Enter Go to Sub Screen 17