DATA SHEET PIC Microcontrollers Order code Manufacturer code Description 73-36 n/a PICF69-I/P (RC) 73-364 n/a PICF69-I/SN (RC) 73-34 n/a PICF675-I/P (RC) 73-36 n/a PICF675-I/SN MICROCONTROLLER (RC) PIC Microcontrollers The enclosed information is believed to be correct, Information may change without notice due to product improvement. Users should ensure that the product is suitable for their use. E. & O. E. Page of 6 Revision A //006 Sales: 006 7566 Technical: 006 35555 Fax: 006 75 Sales@rapidelec.co.uk Tech@rapidelec.co.uk www.rapidelectronics.co.uk
For full datasheet please visit: www.microchip.com PICF69/675 -Pin FLASH-Based -Bit CMOS Microcontroller High Performance RISC CPU: Only 35 instructions to learn - All single cycle instructions except branches Operating speed: - DC - 0 MHz oscillator/clock input - DC - 00 ns instruction cycle Interrupt capability -level deep hardware stack Direct, Indirect, and Relative Addressing modes Special Microcontroller Features: Internal and external oscillator options - Precision Internal 4 MHz oscillator factory calibrated to ±% - External Oscillator support for crystals and resonators - 5 µs wake-up from SLEEP, 3.0V, typical Power saving SLEEP mode Wide operating voltage range -.0V to 5.5V Industrial and Extended temperature range Low power Power-on Reset (POR) Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) Brown-out Detect (BOD) Watchdog Timer (WDT) with independent oscillator for reliable operation Multiplexed MCLR/Input-pin Interrupt-on-pin change Individual programmable weak pull-ups Programmable code protection High Endurance FLASH/EEPROM Cell - 00,000 write FLASH endurance -,000,000 write EEPROM endurance - FLASH/Data EEPROM Retention: > 40 years Low Power Features: Standby Current: - na @.0V, typical Operating Current: -.5 µa @ 3 khz,.0v, typical - 00 µa @ MHz,.0V, typical Watchdog Timer Current - 300 na @.0V, typical Timer oscillator current: - 4 µa @ 3 khz,.0v, typical Peripheral Features: 6 I/O pins with individual direction control High current sink/source for direct LED drive Analog comparator module with: - One analog comparator - Programmable on-chip comparator voltage reference (CVREF) module - Programmable input multiplexing from device inputs - Comparator output is externally accessible Analog-to-Digital Converter module (PICF675): - 0-bit resolution - Programmable 4-channel input - Voltage reference input Timer0: -bit timer/counter with -bit programmable prescaler Enhanced Timer: - 6-bit timer/counter with prescaler - External Gate Input mode - Option to use OSC and OSC in LP mode as Timer oscillator, if INTOSC mode selected In-Circuit Serial Programming TM (ICSP TM ) via two pins Device Program Memory FLASH (words) SRAM (bytes) Data Memory EEPROM (bytes) * -bit, -pin devices protected by Microchip s Low Pin Count Patent: U.S. Patent No. 5,47,450. Additional U.S. and foreign patents and applications may be issued or pending. I/O 0-bit A/D (ch) Comparators Timers /6-bit PICF69 04 64 6 / PICF675 04 64 6 4 / 003 Microchip Technology Inc. DS490C-page
PICF69/675 Pin Diagrams -pin PDIP, SOIC, DFN-S VDD GP5/TCKI/OSC/CLKIN GP4/TG/OSC/CLKOUT GP3/MCLR/VPP 3 PICF69 7 6 4 5 VSS GP0/CIN+/ICSPDAT GP/CIN-/ICSPCLK GP/T0CKI/INT/COUT VDD GP5/TCKI/OSC/CLKIN GP4/AN3/TG/OSC/CLKOUT GP3/MCLR/VPP 3 PICF675 7 6 4 5 VSS GP0/AN0/CIN+/ICSPDAT GP/AN/CIN-/VREF/ICSPCLK GP/AN/T0CKI/INT/COUT DS490C-page 003 Microchip Technology Inc.
PICF69/675 TABLE -: PICF69/675 PINOUT DESCRIPTION Name Function Input Type Output Type Description GP0/AN0/CIN+/ICSPDAT GP0 TTL CMOS Bi-directional I/O w/ programmable pull-up and AN0 AN A/D Channel 0 input CIN+ AN Comparator input ICSPDAT TTL CMOS Serial programming I/O GP/AN/CIN-/VREF/ ICSPCLK GP TTL CMOS Bi-directional I/O w/ programmable pull-up and AN AN A/D Channel input CIN- AN Comparator input VREF AN External voltage reference ICSPCLK ST Serial programming clock GP/AN/T0CKI/INT/COUT GP ST CMOS Bi-directional I/O w/ programmable pull-up and AN AN A/D Channel input T0CKI ST TMR0 clock input INT ST External interrupt COUT CMOS Comparator output GP3/MCLR/VPP GP3 TTL Input port w/ MCLR ST Master Clear VPP HV Programming voltage GP4/AN3/TG/OSC/ CLKOUT GP4 TTL CMOS Bi-directional I/O w/ programmable pull-up and AN3 AN A/D Channel 3 input TG ST TMR gate OSC XTAL Crystal/resonator CLKOUT CMOS FOSC/4 output GP5/TCKI/OSC/CLKIN GP5 TTL CMOS Bi-directional I/O w/ programmable pull-up and TCKI ST TMR clock OSC XTAL Crystal/resonator CLKIN ST External clock input/rc oscillator connection VSS VSS Power Ground reference VDD VDD Power Positive supply Legend: Shade = PICF675 only TTL = TTL input buffer, ST = Schmitt Trigger input buffer DS490C-page 6 003 Microchip Technology Inc.
PICF69/675 4. Package Details The following sections give the technical details of the packages. -Lead Plastic Dual In-line (P) 300 mil (PDIP) E D n α E A A c A L β eb B B p Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n Pitch p.00.54 Top to Seating Plane A.40.55.70 3.56 3.94 4.3 Molded Package Thickness A.5.30.45.9 3.30 3.6 Base to Seating Plane A.05 0.3 Shoulder to Shoulder Width E.300.33.35 7.6 7.94.6 Molded Package Width E.40.50.60 6.0 6.35 6.60 Overall Length D.360.373.35 9.4 9.46 9.7 Tip to Seating Plane L.5.30.35 3. 3.30 3.43 Lead Thickness c.00.0.05 0.0 0.9 0.3 Upper Lead Width B.045.05.070.4.46.7 Lower Lead Width B.04.0.0 0.36 0.46 0.56 Overall Row Spacing eb.30.370.430 7.7 9.40 0.9 Mold Draft Angle Top α 5 0 5 5 0 5 Mold Draft Angle Bottom β 5 0 5 5 0 5 * Controlling Parameter Significant Characteristic Notes: Dimensions D and E do not include mold flash or protrusions. Mold flash or protrusions shall not exceed.00 (0.54mm) per side. JEDEC Equivalent: MS-00 Drawing No. C04-0 DS490C-page 6 003 Microchip Technology Inc.
PICF69/675 -Lead Plastic Small Outline (SN) Narrow, 50 mil (SOIC) E E p D B n 45 h α c A A φ β L A Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n Pitch p.050.7 Overall Height A.053.06.069.35.55.75 Molded Package Thickness A.05.056.06.3.4.55 Standoff A.004.007.00 0.0 0. 0.5 Overall Width E..37.44 5.79 6.0 6.0 Molded Package Width E.46.54.57 3.7 3.9 3.99 Overall Length D.9.93.97 4.0 4.90 5.00 Chamfer Distance h.00.05.00 0.5 0.3 0.5 Foot Length L.09.05.030 0.4 0.6 0.76 Foot Angle φ 0 4 0 4 Lead Thickness c.00.009.00 0.0 0.3 0.5 Lead Width B.03.07.00 0.33 0.4 0.5 Mold Draft Angle Top α Mold Draft Angle Bottom β * Controlling Parameter Significant Characteristic Notes: Dimensions D and E do not include mold flash or protrusions. Mold flash or protrusions shall not exceed.00 (0.54mm) per side. JEDEC Equivalent: MS-0 Drawing No. C04-057 003 Microchip Technology Inc. DS490C-page 7