System Configuration and order-information Guide RX200 S2 January 2006
Front View Power Supply (optional) Floppy Disk Drive CD-ROM Drive (optional) Hard Disk Bay Hard Disk Bay Back View Power Supply 10/100/1000 Base-T Connector Display Serial Port Keyboard Mouse Inside View DIMM Slot System Fan
Instruction This document contains basic product and configuration information that will enable you to configure your system. Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. You can configure your individual PRIMERGY server in order to meet your specific requirements. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. The color of the junction means as follows. Key to Or And
Data Sheet Type Dual-Processor Rack Server Base Unit PGUR2023A CPU Frequencies 64-bit Intel Xeon 3.80GHz *6/3.40EGHz *7/3.20EGHz *8/3EGHz Second-Level-Cache 2MB Multi-Processor 1 (max. 2) Front-Side-Bus 800MHz Chipset Intel E7520 Memory Standard 1GB (512MB ECC DDR2 SDRAM DIMM x 2) Maximum *1 16GB (2GB ECC DDR2 SDRAM DIMM x 8) Graphics Controller ATI RAGE XL, VRAM:8MB (PCI) Resolution *2 640x480/800x600/1024x768/1280x1024 dot Internal Bays Number of bays 2 (hot plug) 3.5 inch Available HDD *3 73.4GB (PG-HDH71K) 10krpm, U320 SCSI HDD 146.8GB (PG-HDH41K) 10krpm, U320 SCSI 300.0GB (PG-HDH31K) 10krpm, U320 SCSI 73.4GB (PG-HDH75K) 15krpm, U320 SCSI 146.8GB (PG-HDH45V) 15krpm, U320 SCSI Maximum *3 600.0GB (300.0GB x 2) CD-ROM optional (Max 24 ATAPI) s PCI-X (64bit/66MHz) *4 1 (Low Profile PCI Card Only) PCI-X (64bit/133MHz) 1 (Low ProfilePCI Card / Full Height PCI Card) SCSI Controller Ultra320 SCSI x 1ch (with RAID1 function) Internal FDD 3.5inch (1.44MB/720KB) Network Controller (onboard) 2 ports (1000 BASE-T/100 BASE-TX/10BASE-T) Interfaces CRT (Analog RGB), Serial Port (D-SUB 9pins) Keyboard (PS/2type Mini DIN 6pins), Mouse (PS/2type Mini DIN 6pins), USB x3 (ver. 2.0) Server Management Software ServerView (Standard) Power supply Voltage AC100V (50/60Hz) / 200V (50/60Hz) x1(max. 2) Power consumption 500W / 1800kJ/h (max.) Redundant power supply optional Redundant Fan yes (Redundant Fan is not available for System Fan) Dimensions (mm) 430 (482 incl. protruding parts)(w) x 710 (770 incl. protruding parts)(d) x 43.6 (1U) (H) Weight 19kg (max.) Environmental Conditions Temperature10-35 C / Humidity 20-80% (non condensing) OS Support *5 Windows Server TM 2003, Standard Edition/Windows Server TM 2003, Enterprise Edition Windows Server TM 2003, Standard x64 Edition/Windows Server TM 2003, Enterprise x64 Edition Windows 2000 Server/Windows 2000 Advanced Server Red Hat Enterprise Linux ES (v.3 for x86)/red Hat Enterprise Linux ES (v.4 for x86) Red Hat Enterprise Linux AS (v.3 for x86)/red Hat Enterprise Linux ES (v.4 for EM64T) Attached tool (Standard) ServerStart (Setup Support tool) *1. Available memory capacity will be changed by the type of OS. Please find more details in Notes[Memory OS Compatibility List]. *2. Resolution is subject to function of the display and OS. *3. HDD capacity is calculated according to the formula 1GB=1000 3 byte. *4. When the PCI card not applicable for PCI-X is installed in PCI slot 2, the system work at 33MHz. *5. Drivers for Linux are not attached. Please download and use drivers of the following URL. http://www.fujitsu.com/global/services/computing/server/ia/driver/ *6. CPU Conversion kit: Xeon(3.0GHz/2MB) -> Xeon(3.8GHz/2MB)(PGBFU34D) is available for upgrading to 64-bit Intel Xeon 3.80GHz. *7. CPU Conversion kit: Xeon(3.0GHz/2MB) -> Xeon(3.4GHz/2MB)(PGBFU34C) is available for upgrading to 64-bit Intel Xeon 3.40EGHz. *8. CPU Conversion kit: Xeon(3.0GHz/2MB) -> Xeon(3.2GHz/2MB)(PGBFU243) is available for upgrading to 64-bit Intel Xeon 3.20EGHz.
Configuration Diagram Power Supply Unit s PCI 1 64bit/133MHz *1 PCI 2 64bit/66MHz *2*3 Memory DIMM Slot A4 DIMM Slot B4 DIMM Slot A3 DIMM Slot B3 DIMM Slot A2 DIMM Slot B2 DIMM Slot A1 DIMM Slot B1 Hard Disk 3.5inch Bay (hot plug) Standard Drive Cage Bay 1 SCSI Bay 2 SCSI Power Supply Unit CPU Xeon 3.80/3.40E/ 3.20E/3EGHz (2MB) 3.5 inch FDD 3.5 inch HDD Bay 1 (hot plug) Xeon 3.80/3.40E/ 3.20E/3EGHz (2MB) CD-ROM Drive 3.5 inch HDD Bay 2 (hot plug) *Components installed as standard configuration marked in grey. *1:PCI 1 for Full Height PCI card, LowProfile PCI card *2:PCI 2 for LowProfile PCI card *3.When the PCI card not applicable for PCI-X is installed in PCI slot 2, the system work at 33MHz. Mountable I/O Options Priority Mount Priority Mountable Cards Bus 1 2 PCI-X 64bit/ 64bit/ 133MH 66MH z z*1 Full Height/ Low Low Profile Profile Max No. of Mount Remarks High Low RAID Ctrl 2-Channel 128MB w/bbu Eth. Ctrl 1000-BASE-T Cu Eth. 2x 1000-BASE-T Cu PG-1862 PCI-X/64bit External array No AFT support Fibre Channel Controller PG-FC107 / PGBFC107 PCI-X/64bit 1-1 Eth. Ctrl 1000-BASE-SX Fibre LC lp PG-1882L PCI-X/64bit 1 2 2 2 LowProfile PCI Card Eth. Ctrl 1000-BASE-T Cu lp PG-1892L / LowProfile PCI Card PCI-X/64bit 1 2 2 PGB1892L SCSI Ctrl U160 lp Remote Service Board PG-142E3 / PGB142E3 PG-1852 / PGB1852 PG-130L / PGB130L PG-RSB103L / PGBRSB103L PCI/64bit PCI/32bit PCI/64bit 1 *-:cannot be applied *1.When the PCI card not applicable for PCI-X is installed in PCI slot 2, the system work at 33MHz. *2.Eth. 2x 1000-BASE-T Cu (PG-1862) can not use together with other LAN cards. - 3.3V 1-1 - 1-2 1 2 1 1 1 *2 2 1 LowProfile PCI Card, External SCSI connector LowProfile PCI Card
Connection Table CPU CPU Slot Max: 2 CPU Processor Xeon 3.0GHz/2MB PG-FG242 PGBFG242 (for CTO) *. This option is available when the processor of the base unit is Processor Xeon 3.0GHz/2MB. Processor Xeon 3.2GHz/2MB PG-FG243 PGBFG243 (for CTO) *. This option is available when CPU Conversion Kit: Xeon (3.0GHz/2MB) Xeon(3.2GHz/2MB) (PGBFU243) is applied. Processor Xeon 3.4GHz/2MB PG-FG34C PGBFG34C (for CTO) *. This option is available when CPU Conversion Kit: Xeon (3.0GHz/2MB) Xeon(3.4GHz/2MB) (PGBFU34C) is applied. Processor Xeon 3.8GHz/2MB PG-FG34D PGBFG34D (for CTO) *. This option is available when CPU Conversion Kit: Xeon (3.0GHz/2MB) Xeon(3.8GHz/2MB) (PGBFU34D) is applied. *CPU Conversion Kit (available only as a Configure To Order (CTO) option; no separate shipment as a loose part is possible) Type CPU Conversion Kit: Xeon(3.0GHz/2MB) Xeon(3.2GHz/2MB) (for CTO) CPU Conversion Kit: Xeon(3.0GHz/2MB) Xeon(3.4GHz/2MB) (for CTO) CPU Conversion Kit: Xeon(3.0GHz/2MB) Xeon(3.8GHz/2MB) (for CTO) Product ID PGBFU243 PGBFU34C PGBFU34D 64-bit Intel Xeon 3EGHz 64-bit Intel Xeon 3.20EGHz Convert the CPU installed as standard in the base unit to the other. (Note: This option can be ordered only as coupled with the base unit. A separate shipment as a loose part is not possible.) 64-bit Intel Xeon 3EGHz 64-bit Intel Xeon 3.40EGHz Convert the CPU installed as standard in the base unit to the other. (Note: This option can be ordered only as coupled with the base unit. A separate shipment as a loose part is not possible.) 64-bit Intel Xeon 3EGHz 64-bit Intel Xeon 3.80GHz Convert the CPU installed as standard in the base unit to the other. (Note: This option can be ordered only as coupled with the base unit. A separate shipment as a loose part is not possible.) Memory Memory Slot Max: 16GB (2GB DIMM x 8) Memory Module-1GB (512MB DIMM x 2) PG-RM1BC Standard Memory Module: 1GB (512MB DIMM x 2) Memory Module-2GB (1GB DIMM x 2) PG-RM2BC Memory Module-4GB (2GB DIMM x 2) PG-RM4BC Memory Slot Memory Module Conversion kit (for CTO) 1GB 2GB Memory Module Conversion kit-2gb (1GB DIMM x 2) PGBRU2BC (for CTO) Memory Module Conversion kit-4gb (2GB DIMM x 2) 1GB 4GB PGBRU4BC (for CTO) (Note: Available Memory Area) Mounted Memory Available Memory Area ~3.0GB Same as the size of mounted memory 4.0~16.0GB Size of Mounted Memory minus "~0.63GB" (Note: "0.1-0.63GB" which is being used for PCI resource management depends on the type and the number of installed memory modules.
Connecting Internal HDD and Internal Backup Devices Internal HDD on board SCSI controller SCSI/RAID Configuration HDD U320 10k 73GB hot plug 1" PG-HDH71K PGBHDH71K (for CTO) HDD U320 10k 147GB hot plug 1" PG-HDH41K PGBHDH41K (for CTO) HDD U320 10k 300GB hot plug 1" PG-HDH31K PGBHDH31K (for CTO) HDD U320 15k 73GB hot plug 1" PG-HDH75K PGBHDH75K (for CTO) HDD U320 15k 147GB hot plug 1" PG-HDH45V PGBHDH45V (for CTO) Internal CD-ROM/DVD-RAM On Board IDE Controller Max : 1 CD-ROM ATAPI PG-CD321 PGBCD321 (for CTO) DVD-RAM ATAPI PGBDVA101 (for CTO) * DVD-RAM drive supports Read function, but does not support Write function. Internal backup device (PRIMERGY SX10) PCI Bus SCSI Ctrl U160 lp SCSI Cable HDCI 1.8m PRIMERGY SX10 PG-130L PG-CBLS007 PG-R1BC4 PGB130L (for CTO) SCSI Cable HDCI 5m PG-CBLS008 *Please find more information on the internal backup devices for PRIMERGY SX10 in Rackmount [Internal Backup Devices with PRIMERGY SX10 ] Power Supply Units Power Supply Slot Power Supply Module PG-PU116 PGBPU116 (for CTO)
LAN Card PCI Bus Eth. Ctrl 1000-BASE-SX Fibre LC lp PG-1882L Multi Mode Fibre Channel Cable Eth. Ctrl 1000-BASE-T Cu lp PG-1892L PGB1892L (for CTO) *for PCI-X Twist Pair Cable Eth. Ctrl 2x 1000-BASE-T Cu PG-1862 *Dual port Eth. Ctrl 1000-BASE-T Cu PG-1852 PGB1852 (for CTO) *No AFT Support On-board LAN Server Management Card Remote Service Board PG-RSB103L PGBRSB103L (for CTO) Twist Pair Cable Specifications are subject to change without notice. For the latest detailed information, contact your local representative. All brand names and product names are trademarks and registered trademarks of their respective holders. 2006 Fujitsu Limited. All rights reserved. Printed in Japan. Global Business Development & Marketing Business Strategy & Planning System Products URL http://primergy.fujitsu.com