Model Name Model Code PSOV550102U PSOV550102W PSOV550102V Features : ㅡ Flickerless ㅡ Full-protection provided: OCP/OVP/OTP/SCP/OLP ㅡ Low Power Dissipation (Stand-by mode : <0.5Wh) ㅡ Wide Vout : 25 ~ 46Vdc ㅡ Compliant with CB, CE, KC safety requirements for LED lighting ㅡ Constant Current Type ㅡ IP 67 E480967
Electrical specification No. 1 16 17 22 23 26 31 Item 2 Variable Input Voltage 108-300 Vac 3 Maximum Input Current - - 0.6 Arms 4 5 Power Factor (PF) 90 - - % 1) 6 Total Harmonic Distortion (THD) - - 20 % 1) 13 14 18 19 20 21 24 25 27 28 29 30 Nominal Input Voltage Nominal Input Frequency 12V Output Voltage Ripple - - ± 1.2 Vdc 20MHz Bandwidth, 2) Output Open LED Protection Storage Temperature Surge Insulation Resistance Input to Case - 3.75 - - 0.5 - - ma Wh Vdc 25 50 Case Temperature (Tc) - 50 85 Dielectric Withstand Voltage ESD LED Output Voltage Adjustable of LED Current 12V Output Voltage Humidity 20-85 % Input to Output Output to Case MΩ kv kv @Vpeak Apply for 1 minute Line to Line 6 7 - kv 4) Line to Ground Contact Discharge Air Discharge 120 220 277 47 50/60 63 25-46 700-1050 10.8 12 13.2 - - 100 Output Short Circuit Protection - - - - Operating Temperature Min Typ Max Unit Remark 7 Inrush Current - - 60 Arms Duration 500μs, 9) Meets NEMA 410 8 Electrical Efficiency 85 88 - % 2) 9 Turn-on Delay - - 0.5 s 10 11 12 15 LED Output Current LED Output Current Ripple 12V Output Current STBY Power Dissipation 998 1050 1103 - - 105 - - 0.5 - - 59-40 25 80-40 10 - - 3.75-8 9-4 - - 8 - - Vac Hz ma Vdc Vdc kv kv kv kv @Cold Start, 3) @46Vdc Load ma 20 MHz Bandwidth, 2) ma Rset 2) LED Off_Remote Low No Damage Ta = 59 500Vdc between Input & Output 6) 4) 5) 5)
Application Notes 1) Test Condition:120/277Vac 50/60Hz Input,Typical LED Load,Ambient Temperature 25, Measure at the cable-end 2) Test Condition: 220Vac 60Hz Input, LED Max. Load, 30min Aging, Ambient Temperature 25 3) The interval of turn on/off should be over 1sec. 4) Surge Specification above is higher than IEC/EN 61000-4-5 Level 4 (Differential 2kV, Common 4kV ) 5) The metal case of the LED driver must be connected with F.G 6) ESD Specification above meets IEC/EN 61000-4-2 Requirements (Contact Level 2, Air Level 3) 7) The metal case of the driver should be grounded. 8) Determined by Paragraph 34.1.2, UL1310 or Paragraph 8.4.2, UL8750, EN61347-1, EN61347-2-13 9) NEMA 410 peak current requirement Complied I 2 t(a 2 sec) @ peak 2ms Safety Standards Including safety requirements above, the LED driver complies with the following safety standards: No. Item Description 1 IEC/EN 61347-1, IEC/EN 61347-2-13 IEC/EN Safety Standards 2 IEC/EN 55015 Conducted and Radiated Emission Test 3 IEC/EN 61000-3-2 Harmonic current emissions: Class C 4 IEC/EN 61000-3-3 Voltage Fluctuations and Flicker 5 IEC/EN 61000-4-2 Electrostatic Discharge (ESD): Contact Level 2, Air Level 3 6 IEC/EN 61000-4-3 Radio-frequency Electromagnetic Fields 7 IEC/EN 61000-4-4 Electrical Fast Transients (EFT) 8 IEC/EN 61000-4-5 Surges: Level 4 9 IEC/EN 61000-4-6 Injected Currents 10 IEC/EN 61000-4-8 Power Frequency Magnetic Fields 11 IEC/EN 61000-4-11 Voltage Dips and Short Interruptions
Operating window Flickerless / Dim Power supply *Currently Measurement Data Life Time vs Tcase 120000 100000 Life Time [hrs] 80000 60000 40000 20000 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 Tc [ ] Remark) LED Driver has a rated lifetime of 50,000 hours @ Tc 70
Power Factor(%) Power Factor 100.00% 90.00% 80.00% 70.00% 60.00% THD(%) Flickerless / Dim Power supply 50.00% 120 220 277 Input Voltage (Vac) *Currently Measurement Data 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA THD 35.00% 30.00% 25.00% 20.00% 15.00% 10.00% 5.00% 0.00% 120 220 277 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA Efficiency(%) Eff 100.00% 90.00% 80.00% 70.00% 60.00% 50.00% 120 220 277 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA
Output Current( ma ) Flickerless / Dim Power supply *Currently Measurement Data Current 1200.00 1000.00 800.00 600.00 400.00 200.00 0.00 120 220 277 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA Dimming curve Current 1200.00 1000.00 800.00 600.00 400.00 200.00 0.00 10 9.3 9 8 7 6 5 4 3 2 1 0 Input Voltage (Vac) 9LED-700mA 9LED-1050mA 12LED-700mA 12LED-1050mA 15LED-700mA 15LED-1050mA
*Currently Measurement Data Adjustable of Current( Rset ) 1100 1050 LED Current [ma] 1000 950 900 850 800 750 700 900 9,000 90,000 900,000 Rset [Ω] Rset Adjustable of Current( Rset ) - detail 1100 1050 LED Current[mA] 1000 950 900 850 800 750 700 900 5,900 10,900 15,900 20,900 Rset [Ω]
Mechanical Specification PSOV550102U PSOV550102W PSOV550102V Enclosure Size Unit Width Length Height Mount Length Overall Length mm 53.6 177.6 33.9 185.4 192.6 inch 2.11 6.99 1.33 7.30 7.58 Case Material : Aluminium
Wiring Diagram Flickerless / Dim Power supply LIVE : Black Neutral : White Out connector description Code PSOV550102U Logo Connector (Cable end) Connector (opposite side) PSOV550102W SOLUM MG610320(KET) MG640322(KET) PSOV550102V L N LED Control gear N.A 02R-JWPF-VSLE-S(JST) or 02R-JWPKF-VKLE-S(JST) N.A 02T-JWPF-VSLE-S(JST) L L E S D R V G G or 02T-JWPKF-VKLE-S(JST) LED : Blue LED + : Red Vsen : White Rset : Orange DIM : Violet RMT : Green 12V : Yellow GND : Black GND : Blue Remark MG610320(KET) 02R-JWPF-VSLE-S(JST) 02R-JWPKF-VKLE-S(JST) Caution 1) Before installing LED driver, AC power should be turned off. After installing LED driver, AC power should be turned on. 2) When this LED driver are installed as an independent lamp controlgear, end-customer should protect connecting leads of pri/sec. cable with a certified element. 3) Waterproof connector or Junction box can be assembled with output cables for operating in dry/wet/damp or outdoor environment. 4) Wires should be less than 1m when installed in final equipment 5) Do not detach input and output wires after complete installation. 6) The metal enclosure should be grounded in purpose of EMC performance. 2nd Signal Description Name Feature Description Vsen check LED Out Voltage Monotoring LED Open/Short (for Connectivity Module) Rset Adjustable of current Control LED Output Current DIM Dimming Control Brightness RMT LED On/Off Stand by Mode 12V Control Source Supply Controller Power GND 2nd GND Signal GND GND 2nd GND Signal GND
Rating Label Drawing
Barcode Label 2017-01-01 H 1 1 7 1 0 1 * * * 0 0 0 1 REV.A01 DATE BARCODE LOT NO 7 DEVELOPMENT Rev X01~99 MP Rev A01~99 6 SERIAL No _4 Digit 5 MODEL CODE _3 Digit 4 PRODUCTION DATE _2 Digit 3 PRODUCTION MONTH _1 Digit 2 PRODUCTION YEAR _2 Digit 1 PRODUCTION COUNTRY Mean 1.PLANT 2. YEAR 3. MONTH 4. DATE 5. CODE 6. SERIAL 7. Revision No Digit 2 2 1 2 3 4 EX. C1 : DGSM C2 : Solytech K1 : Korea H1 : SOLUM VINA 00~99 1...9,A,B 01~31 PSOV550102U : 236 PSOV550102W : 388 PSOV550102V : 266 0001.. 9999 X01~99 : DEVELOPMENT A01~99: MP Material Code ITEM LOT No Quantity [PCS] EXP. Date REV. A** ********* MAKER 24 SOLUM 20**.**.** ~ 20**.**.** USER Model Code SOLUM Model Code SOLUM LOT NO & Quantity of Products Product Date ~ After 5 years ************* **** ********* USER Barcode
Packing Drawing 1. Out Box Dimmension Weight Quantity 540(L) 355(W) 170(H) [mm] < 14Kg 24EA / 1Box TRY BODY NIL PAD OUT BOX 2. Pallet Weight Quantity < 420Kg 30BOX / 1Pallet
Connecting the control module Standard LED Driver Wired Module System Control DALI Master DMX Master DMX Wireless Module Sensor Switch Control Unified Dim IR Zigbee Remocon BLE LoRa Sensor Module ALS Automatic Switch & Bright PIR Occupancy Combined Module Communication + Sensor Line-Up for SoluM control module Communication Module Sensor Module Combined Module [DALI] PSDMDAD101A [DMX512] PSDMXAD102A [BLE] PSDMBAD103A [IR] PSDMRAD104A [Light-ON/OFF] PSDMSEL103A [Occupancy] PSDMSEM102A [DALI-BLE] PSDMDBC102A [DMX-BLE] PSDMXBC103A [BLE-Sensor] PSDMBSC104A