3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 www.nav-tv.com info@nav-tv.com A3/GOLF 7-CAM NTV-KIT500 Overview The A3/GOLF7-CAM Kit allows the user to add 1 video input and a backup camera input (with active parking lines!) to the factory media screen in the 2014 Audi A3 or VW Golf 7. Installation is performed behind the MMI (inside glove box). Kit Contents CAM Input Harness LVDS Video Cable Optional: NTV-KIT496 A3/GOLF7 Interface Power/CAN Harness AUDI 3G-CAM NTV-CAM072 Aux Video in Cable 1 P a g e
Interface Connectors Power/CAN Video IN Rear-CAM IN/CAM Power LVDS OUT (to screen) LVDS IN (from radio) Dip Switches Dip Switch Settings Quick Reference AUDI A3 without NAV VW GOLF VII without NAV AUDI A3 with NAV VW GOLF VII with NAV Settings shown here are with MENU set to ON and AUX VIDEO set to OFF. See next page for further adjustments. 2 P a g e
Dip Switch Settings* Extended Information Audi A3 (No NAV) UP OFF X X X OFF DOWN X ON ON Audi A3 (With NAV) UP OFF X X OFF DOWN X ON X ON Golf VII (No NAV) UP X OFF X X X OFF DOWN ON ON Golf VII (With NAV) UP X OFF X X OFF DOWN ON X ON *Note: Remove power to the unit prior to making adjustments to the dip switches. IMPORTANT DIP SWITCH NOTES: AUX Video: Default use for AUX Video is for a front camera image. This is why AUX video shows for ~10 seconds when the vechicle is placed in drive. This command is adjustable in the Menu. Make sure dip switch #6 is down in order to enter the Menu. Car Select: If the car does not switch to the reverse image when in reverse, try placing dip switch #1 in the other position. Resolution: Down for high-res, larger screens (typically with navigation). Up for lowerres, smaller screens (typically without navigation). 3 P a g e
Installation 1. With VW radio keys, remove the MMI located in glove box. Disconnect any associated harnesses and set the radio aside. 2. Gather the provided Power/CAN Harness from the A3/GOLF7 kit. Connect the following wires to the car radio s main power plug*: *Note: These connections are not used for VW GOLF VII. Interface wires Connect to car Radio Plug Black (Ground) Chassis Ground PIN 15 (Brown) Yellow (Constant 12v) Constant 12v (+) PIN 16 (Red/Yellow) White (MON-CAN H) CAN HI PIN 1 (Orange/Black) Green (MON-CAN L) CAN LO PIN 7 (Orange/Brown) White (PAS-CAN H) CAN HI PIN 6 (Orange/Violet) Green (PAS-CAN L) CAN LO PIN 12 (Orange/Brown) 3. Locate the factory Pink (For AUDI s with NAV, this connector is GRAY), 4-pin round connector that was removed from the radio in step 1. Connect this factory plug to the A3/GOLF7 interface at the port labeled LVDS OUT.* *NOTE: You may need to shave some keyways on the factory connector in order for it to fit into the LVDS-IN plug. 4 P a g e
4. Connect the smaller white plug side of the provided LVDS Video Cable to the port on the A3/GOLF7 interface labeled LVDS- IN. 5. Connect the free end of the provided LVDS Video Cable back to the factory radio at the appropriate port. 6. Connect the AV Input cable to the 4-pin port on the A3/GOLF7 interface labeled CAMERA IN. 7. Connect ground and power for your camera to the black (GROUND) and red (REAR 12V OUT) wires from the provided CAM input harness. NOTE: This power source will only supply 12v when the vehicle is in reverse. 8. Connect the white plug from the Power/CAN Harness to the port on the A3/GOLF7 interface labeled POWER/CAN. 9. Optional: If adding an additional video input, connect the provided Video in Harness to the 2-pin port on the interface labeled CAMERA IN. Note: if adding an additional video input, dip switch 2 must be in the down position. By default, AUX Video is used for a front camera (which will show the AUX image for ~10 secs when in Drive), this option is adjustable via the main Menu. 10. Optional: If you re installing the optional AUDI 3G- CAM, remove the grid lines by cutting the green wire near the connector: Installation continues on next page 5 P a g e
11. GOLF VII ONLY: If this car does not have OEM PDC (Parking sensors in the rear bumper), you MUST setup this module differently. Follow the steps below: a. Disconnect the main Power/CAN connector from the module b. Locate the dip switches on the side of the module and verify that dip switch 6 is DOWN (the rest are less important). c. Re-connect the main Power/CAN connector. Turn the car on and wait for the radio to boot and settle. d. Press and HOLD the OK button on the steering wheel for 5 seconds. An OSD menu will appear on the factory media screen. e. Navigate to PDC under Rear view camera settings and turn this option OFF. f. Save the configuration and return to the factory screen. 12. Start the car and test for proper functionality before replacing any dash pieces. 6 P a g e
A3 Controls (MMI knob) Press quickly: DISPLAY AUX VIDEO Rotate/Click: To navigate MENU/Select option Hold for 5 seconds: ENTER MENU Press: Return to previous menu Not shown: inav button on steering wheel: hold for 3 seconds to display AUX Video (DIP SW 2 must be down) GOLF 7 Controls (steering wheel) Hold for 5 seconds: ENTER MENU or Select setting Arrows: Navigate menu options Hold for 3 seconds: Cycle Video Input 7 P a g e