Titan Media Cart Installation and Operation Manual
Table of Contents INTRODUCTION SERVICE AND SUPPORT... 1 PRODUCT RETURNS... 1 UNPACKING... 1 TITAN SINGLE MEDIA CART... 2 TITAN DUAL MEDIA CART... 2 BEFORE YOU BEGIN... 3 ASSEMBLY TITAN SINGLE MEDIA CART... 4 Assembling the Hardware...4 Mounting the screen...6 TITAN DUAL MEDIA CART... 7 Assembling the Hardware...7 Mounting the Screens...9 ATTACHING A PTZ CAMERA... 10 ATTACHING THE CODEC SHELF... 11 APPENDIX SPECIFICATIONS... 12 TITAN MEDIA CART INSTALLATION AND OPERATION MANUAL CLEARONE PART NO. 800-300-101 JANUARY 2012 (REV. 4.1) 2012 ClearOne Communications, Inc. All rights reserved. No part of this document may be reproduced in any form or by any means without written permission from ClearOne Communications. Printed in the United States of America. ClearOne reserves specific privileges. Information in this document is subject to change without notice
Introduction The Titan Media Carts provide superior strength, mobility and storage space. They are a perfect blend of heavy duty construction and professional styling. Our durable metal carts are an attractive, highly functional addition to any conferencing environment. The ability to hold one screen (single cart) or two screens (dual cart) makes Titan perfect for large conference rooms or distance learning facilities. See the Specifications section on page 12 for maximum screen sizes. Service and Support If you need additional information on how to install, set up or operate your Titan Media Cart, please contact us. We welcome your comments so that we can continue to improve our products and better meet your needs. Support Tel: 1.800.283.5936 1.801.974.3760 Fax: 1.801.974.3669 Email: tech.support@clearone.com Product Returns All product returns require a return materials authorization (RMA) number. Please contact ClearOne Technical Support before attempting to return your product. Make sure you return all the items that shipped with your product. Unpacking Carefully remove all items that ship with the Titan Media Cart. Ensure you have received all items shown on the following page. If you are missing any items, please contact our Service Department at 1-800-283-5936.»» NOTE: ClearOne is not responsible for product damage incurred during shipment. You must make claims directly with the carrier. Inspect your shipment carefully for obvious signs of damage. If the shipment appears damaged, retain the original boxes and packing material for inspection by the carrier. Contact your carrier immediately. Introduction 1
SHE Titan Single Media Cart Universal Base with Support Top Manual 8-32 Pan Head Screws Qty: 2 Vertical Support Codec Shelf 1/4-20 Screw Qty: 1 5/16 Bolts Qty: 20 5/16 Washers Qty: 12 5/16 Nuts Qty: 12 NOTE: Depending on your options, not all included hardware will be used when assembling the Titan Single Media Cart. Titan Dual Media Cart Universal Base with Support Top Rail Track Bracket Vertical Support Horizontal Support Codec Shelf Manual 1/4-20 Screw Qty: 1 8-32 Pan Head Screw Qty: 2 5/16 Bolts Qty: 20 5/16 Washers Qty: 12 5/16 Nuts Qty: 12 2 Technical Support: 800.283.5936
Before You Begin Before you begin assembling your Titan Media Cart, be sure to have the following: OmniMount 1N1-L screen mount (single screen configuration) or OmniMount VB150F (X2) screen mounts (dual screen configuration) 1/2 wrench Socket wrench with 1/2 socket Phillips screw driver The Titan Media Carts require one mount for each screen that is to be secured to the unit. Both the OmniMount 1N1-L and the OmniMount VB150F include a wall mount that connects to the cart and vertical rails that attach to the back of the monitor. The OmniMount 1N1-L and VB150F are not sold by ClearOne and are not included with the Titan Cart systems, but must be purchased separately. Contact the Service Department at 1-800-283-5936 for more information. Introduction 3
Assembly Titan Single Media Cart ASSEMBLING THE HARDWARE 1. Align the Vertical Support over the self-clinching nuts in the Universal Base. NOTE: The self-clinching nuts are attached to the top of the Universal Base. 2. Secure the Vertical Support using six 5/16 Bolts. Bolts Vertical Support Support Top Universal Base 4 Technical Support: 800.283.5936
3. Remove and set aside the Locking Bar from the OmniMount 1N1-L Flat Panel Mount assembly (not supplied), then securely anchor the mount to the Vertical Support using four 5/16 Bolts, four 5/16 Washers and four 5/16 Nuts. NOTE: The Flat Panel Mount can be attached higher or lower on the Vertical Support depending on desired position and size of screen. Locking Bar and Screws Wall Plate Washers and Nuts Bolts 4. Using hardware supplied with the 1N1-L mount, attach the vertical rails to the back of the screen. (See 1N1-L instructions for more information.) Screen Vertical Rail Assembly 5
MOUNTING THE SCREEN 1. With the aid of another person, lift the screen up to the Flat Panel Mount and align the tabs on the Vertical Rails with the top and bottom horizontal bars of the Flat Panel Wall Mount that is mounted on the vertical support. Locking Bar and Screws Vertical Rails Over Wall Mount Flat Screen Display 2. Slide the screen down into place. 3. Place and secure the Locking Bar with the included screws over the top horizontal bar of the mount, locking the Vertical Rails to the wall mount. NOTE: For instructions on installing the Codec Shelf, see page 11. 6 Technical Support: 800.283.5936
Titan Dual Media Cart ASSEMBLING THE HARDWARE 1. Align the Vertical Support over the self-clinching nuts in the Universal Base. NOTE: The self-clinching nuts are attached to the top of the Universal Base. Bolts Vertical Support Support Top Universal Base 2. Secure Vertical Support using six 5/16 Bolts. 3. Line up the Horizontal Support alignment pins with the guiding holes on the Vertical Support at desired height and slide into place. 4. Hold the Horizontal Support in place while securing it to the Vertical Support using six 5/16 Bolts. NOTE: The Horizontal Support can be raised or lowered on the Vertical Support to achieve the desired viewing position of the screens. Horizontal Support Alignment Pin Bolts Assembly 7
5. Attach the Rail Track to the Horizontal Support using two 8-32 Pan Head Screws. 6. Slide the Camera Bracket down over rail. NOTE: Attaching the Camera Bracket is optional. The bracket is normally used with codecs that have a detachable camera or with a small PTZ camera. This bracket allows the camera to be placed at eye-level between the monitors. Camera Shelf Pan Head Screws Rail Track Horizontal Support NOTE: To adjust the Camera Shelf height, pull the Adjusting Pin out of the Rail Track, slide the Camera Bracket to the desired height, and replace the Adjusting Pin. 7. Securely anchor the Wall Plates (not supplied) to the Horizontal Support using eight 5/16 Bolts, eight 5/16 Washers and eight 5/16 Nuts. Washers and Nuts Wall Plate Washers and Nuts Bolts Bolts Horizontal Support NOTE: Adjust the position of the Wall Plates based on the size of the screens. 8 Technical Support: 800.283.5936
8. Using hardware supplied with the Wall Mount, attach the Vertical Rails with the Rubber Stops to the back of the screen. (See OmniMount VB150F instructions for more information.) NOTE: Titan Media Carts require one OmniMount VB150F Wall Mount (not supplied) for each screen that is to be secured to the support. Rubber Stop Vertical Rails MOUNTING THE SCREENS Rubber Stop 1. With the aid of another person, lift the screen up to the Wall Plate attached to the Horizontal Support and align the tabs on the Vertical Rails above the Wall Plate. WARNING: Due to a potential tipping hazard, the cart should not be moved until both screens are securely mounted. Locking Bar Wall Plate Vertical Rail Horizontal Support Assembly 9
2. Lower the screen into place with the Vertical Rails hooking over the Wall Plate. 3. Thread the Locking Bar from the side through the Wall Plate and both Vertical Rails. When fully inserted, turn in place to position locking tab.. NOTE: For instructions on installing the Codec Shelf, please see page 11. Attaching a PTZ Camera 1. Secure the camera to Camera Bracket using the 1/4-20 Screw. Camera Camera Bracket NOTE: Different camera models can be attached to the Camera Bracket using individual mounting hardware supplied by the camera manufacturer. 10 Technical Support: 800.283.5936
Attaching the Codec Shelf NOTE: The Codec Shelf supports a set-top codec or PTZ camera; using the shelf is optional. 1. Align the Codec Shelf with the guiding holes on the Vertical Support. Codec Shelf Washer and Nut Support Top (Screen Mounting Hardware Not Shown.) 2. Secure the Codec Shelf to Vertical Support using the attached bolts on Vertical Support, four 5/16 Washers, and four 5/16 Nuts. NOTE: The Codec Shelf can be positioned on the Vertical Support to accommodate various sizes and styles of screens. Assembly 11
Appendix Specifications Dimensions (W x H x D) 45 x 31 x 28 Assembled Dimensions without screens (W x H x D) Single: 45 x 72 x 28 Dual: 72 x 72 x 28 Integrated Rack Height: 9 space, 15.75 (40 cm) Depth: 22 Rack rails: included Rail recess: 2 clearance from door Casters Heavy duty (250 lb. rating each) 6 1/2 clearance with 5 diameter Caster Composition Precision synthetic, plate-mounted, double ball bearing, with swivel head and polypropylene tread Vented Back Panel Height: 17 Width: 17 Attachment: Four #8-32 screws Weight Capacity 800 lb (364 kg) Construction 14-, 12-, and 11-gauge steel Columnar support, channel welded Screen Support Single: One screen (maximum size 65, 39 1/2 max height) Dual: Two screens (maximum size 56, 51 1/2 max width ea.) Part Numbers 911-300-101 Titan Single Media Cart 911-300-110 Titan Dual Media Cart 12 Technical Support: 800.283.5936
Appendix 13