About the Appliance Installation, page 1 Standalone Mode Requirements, page 3 Cisco DNA Center Appliance, page 3 Prepare for Appliance Installation, page 11 Connect and Power On the Appliance, page 14 Check the LEDs, page 14 Install or Replace Appliance Components, page 17 Configure CIMC, page 18 Use CIMC to Configure the Appliance, page 20 About the Appliance Installation Cisco offers a physical appliance that can be purchased with the Cisco DNA Center ISO image pre-installed and tested. You can deploy this appliance within your network. For this release, you can deploy the appliance as a single host only (single appliance in standalone mode). The following table lists the steps for installing the appliance. Table 1: Cisco DNA Center Appliance Installation Step 1 Review the pre-install checklists for the DNA Center appliance. See Standalone Mode Requirements, on page 3. 1
About the Appliance Installation Step 2 Review information about the appliance and its specifications, including the following: Physical Environmental Power Front and rear panels See Cisco DNA Center Appliance, on page 3. 3 4 5 6 7 8 9 10 11 12 Review information about port usage for DNA Center. See Cisco DNA Center Appliance Ports Reference, on page 9. Prepare the appliance for installation. See Prepare for Appliance Installation, on page 11. Install the appliance in a rack. See Review the Rack Requirements, on page 13. Connect power to the appliance and power it on. See Connect and Power On the Appliance, on page 14. Check the appliance LEDs to ensure the appliance is functional. See Check the LEDs, on page 14. Configure CIMC. See Configure CIMC, on page 18. Use CIMC to configure the appliance to boot from the DNA Center ISO image. See Use CIMC to Configure the Appliance, on page 20. Use the wizard to configure DNA Center for use. See Configure Cisco DNA Center Using the Wizard. Log in to DNA Center for the first time. See Log In to Cisco DNA Center For the First Time. Get DNA Center ready for use. See Perform Post-Installation Tasks. 2
Standalone Mode Requirements Standalone Mode Requirements Review the following requirements before beginning the Cisco DNA Center appliance installation. Multi-Host Requirements This version of DNA Center allows only a single-host deployment for your network. Multi-host deployment is not supported. Networking Interface Requirements In a production installation, you must connect the DNA Center appliance's network ports to your network. Cisco recommends the following cable connections: First 10Gb port in the VIC: Connect to an access switch with connections to the enterprise network. First embedded 1Gb interface: Connect to the dedicated management network (if it exists; Cisco recommends that you create one if it does not already exist). The following connections are either optional or reserved for future use: Second 10Gb port in the VIC: Reserved for future intra-cluster connections (clustering is not supported in this release). 1Gb Ethernet dedicated out-of-band management port: Reserved for OOB management of the appliance chassis. Second embedded 1Gb interface: Optional. You can connect this interface to any isolated network with a static route. However, Cisco recommends that you leave it unconfigured. For a diagram showing these ports, see the back-panel illustration in Cisco DNA Center Appliance Front and Rear Panels, on page 6. IP Address Requirements Before beginning the installation, ensure that your network has sufficient IP addresses available to assign to each of the DNA Center appliance ports you plan on using. You will need a minimum of two addresses: one for the connection to the enterprise network, and one for the 1Gb OOB management port. You will need three if you have a dedicated management network and plan to connect the appliance to the first embedded 1Gb interface, and four if you will also use the second embedded 1Gb inteface for a static-route connection. Internet Access Requirements By default, DNA Center is configured to send product-improvement and usage information to Cisco via the internet. If you do not wish to provide internet connectivity for this purpose, or do not want to participate in the Cisco product improvement program, you can opt out by disabling the telemetry collection parameter in the installed DNA Center's System Settings. To disable the telemetry collection parameter, log into DNA Center and select > System Settings > Settings > Telemetry Collection. Uncheck the Telemetry Collection checkbox, then click Update. Cisco DNA Center Appliance Cisco supplies DNA Center on a physical appliance with an ISO image loaded on the appliance storage. The Cisco DNA Center appliance part number is DN1-HW-APL. You must physically install the appliance on your network, and then configure it using CIMC and the installation wizard. 3
Physical Specifications Physical Specifications The following table lists the physical specifications for the Cisco DNA Center appliance. Table 2: Physical Specifications Height Width Depth (length) Front Clearance Side Clearance Rear Clearance Maximum weight (fully loaded chassis) Specification 1.7 in. (4.32 cm) 16.89 in. (43.0 cm) Including handles: 18.98 in. (48.2 cm) 29.8 in. (75.6 cm) Including handles: 30.98 in. (78.7 cm) 3 in. (76 mm) 1 in. (25 mm) 6 in. (152 mm) 37.9 lb. (17.2 Kg) Environmental Specifications The following table lists the environmental specifications for the Cisco DNA Center appliance. Table 3: Environmental Specifications Temperature, operating Temperature, non-operating (when the server is stored or transported) Humidity (RH), operating Humidity, non-operating Specification 41 to 95 F (5 to 35 C) Derate the maximum temperature by 1 C per every 1000 ft. (305 meters) of altitude above sea level. 40 to 149 F ( 40 to 65 C) 10 to 90%, non-condensing at 82 F (28 C) 5 to 93% at 82 F (28 C) 4
Power Specifications Altitude, operating Altitude, non-operating (when the server is stored or transported) Sound power level Measure A-weighted per ISO7779 LwAd (Bels) Operation at 73 F (23 C) Sound pressure level Measure A-weighted per ISO7779 LpAm (dba) Operation at 73 F (23 C) Specification 0 to 10,000 ft. (3,000 m) 0 to 40,000 ft. (12,192 m) 5.4 37 Power Specifications The specifications for the Cisco DNA Center appliance power supply are listed in the following section. You can get more specific power information for your exact appliance configuration by using the Cisco UCS Power Calculator: http://ucspowercalc.cisco.com Caution Do not mix power supply types in the appliance. Both power supplies must be identical. 770 W AC Power Supply The following table lists the specifications for the dual 770 W AC power supply (Cisco part number UCSC-PSU1-770W) supplied with the Cisco DNA Center appliance. Table 4: AC Power Supply Specifications AC input voltage AC input frequency Maximum AC input current Maximum input volt-amperes Specification Nominal range: 100 120 VAC, 200 240 VAC (Range: 90 132 VAC, 180 264 VAC) Nominal range: 50 to 60Hz (Range: 47 63 Hz) 9.5 A at 100 VAC 4.5 A at 208 VAC 950 VA at 100 VAC 5
Cisco DNA Center Appliance Front and Rear Panels Maximum output power per PSU Maximum inrush current Maximum hold-up time Power supply output voltage Power supply standby voltage Efficiency rating Form factor Input connector Specification 770 W 15 A (sub-cycle duration) 12 ms at 770 W 12 VDC 12 VDC Climate Savers Platinum Efficiency (80Plus Platinum certified) RSP2 IEC320 C14 Cisco DNA Center Appliance Front and Rear Panels The following figure displays the front panel of the Cisco DNA Center appliance. Figure 1: Front Panel, Cisco DNA Center Appliance (DN1-HW-APL) Component 1 2 Drives (eight 2.5-inch SDD drives) Drive bays 1 and 2 support SAS/SATA and NVMe PCIe solid state drives (SSDs). 6
Cisco DNA Center Appliance Front and Rear Panels Component 3 4 5 6 7 8 9 10 11 12 Pull-out asset tag Operations panel buttons and LEDs Power button/power status LED Unit identification button/led System status LED Fan status LED Temperature status LED Power supply status LED Network link activity LED KVM connector (used with KVM cable that provides two USB 2.0, one VGA, and one serial connector) The following figure displays the rear panel of the Cisco DNA Center appliance. Figure 2: Rear Panel, Cisco DNA Center Appliance (DN1-HW-APL) Release 1.1 Figure Callouts Component 1 Grounding-lug hole (for DC power supplies) 2 3 4 5 PCIe riser 1/slot 1 Rear unit identification button/led PCIe riser 2/slot 2 Power supplies (up to two, redundant as 1+1) 7
Summary of Appliance Series Features Component 6 7 8 9 10 11 12 13 First 10Gb port on Cisco Virtual Interface Card (VIC) 1227. Connect to an access switch with connections to the enterprise network. Second 10Gb port on Cisco VIC 1227. Reserved for future intra-cluster connections. USB 3.0 ports (two) 1Gb Ethernet dedicated out-of-band management port. Reserved for OOB management of the appliance chassis. Serial port (RJ-45 connector) VGA video port (DB-15) First embedded (on the motherboard) Intel i350 1Gb ethernet controller port. Connect to the dedicated management network. Second embedded 1Gb ethernet controller port. Optional, for connecting to an isolated network with a static route. Summary of Appliance Series Features The following table lists the Cisco DNA Center appliance features. Table 5: Cisco DNA Appliance Series Features Feature Chassis Processors Memory Baseboard management One rack-unit (1RU) chassis. Up to two Intel Xeon CPU E5-2699 2.20 GHz v4 series processor family CPUs. 24 slots for registered DIMMs (RDIMMs) or load-reduced DIMMs (LRDIMMs) (12 each CPU). BMC, running Cisco Integrated Management Controller (Cisco IMC) firmware. Depending on your port configuration and Cisco IMC (CIMC) settings, you can access CIMC either through the IP address assigned to the 1Gb dedicated management port or the second 10Gb VIC port. 8
Cisco DNA Center Appliance Ports Reference Feature Network and Management I/O Supported connectors: Two 10Gb Ethernet ports on the Cisco UCS Virtual Interface Card (VIC) 1227 One 1Gb Ethernet dedicated management port Two 1Gb BASE-T Ethernet LAN ports One RS-232 serial port (RJ-45 connector) One 15-pin VGA2 connector Two USB3 3.0 connectors One front-panel KVM connector that is used with the KVM cable, which provides two USB 2.0, one VGA, and one serial (DB-9) connector Power Cooling Storage Disk Management (RAID) Video Dual AC power supplies, 770 W AC each. Do not mix power supply types or wattages in the server. Redundant as 1+1. Six hot-swappable fan modules for front-to-rear cooling. Eight 2.5-inch Small Form Factor (SFF) solid state drives (SSDs). Three pre-configured RAID settings: RAID 1 on slots 1 and 2, RAID 1 on slots 3 and 4, and RAID 10 on slots 5, 6, 7, and 8. These settings are not user-configurable. VGA video resolution up to 1920 x 1200, 16 bpp at 60 Hz, and up to 256 MB of video memory. Cisco DNA Center Appliance Ports Reference The following tables list the Cisco DNA Center appliance ports that permit incoming and outgoing traffic. You should ensure that these ports are open for both incoming and outgoing traffic flows. Ensure that proper protections exist in your network for accessing port 2222. For example, you can configure a proxy gateway or secure subnets to access this port. Table 6: Cisco DNA Center Appliance Incoming Traffic Port Reference Port Number 2222 Permitted Traffic SSH Protocol ( or UDP) 9
Cisco DNA Center Appliance Ports Reference Port Number 80 123 162 443 16026 Permitted Traffic HTTP NTP SNMP HTTPS SCEP Protocol ( or UDP) UDP UDP Table 7: Cisco DNA Center Appliance Outgoing Traffic Port Reference Port Number 22 23 53 80 123 161 443 Permitted Traffic SSH (to the network devices) Telnet (to the network devices) DNS Port 80 may be used for an outgoing proxy configuration. Additionally, other common ports such as 8080 may also be used when a proxy is being configured by the DNA Center configuration wizard (if a proxy is already in use for your network). To access Cisco supported certificates and trust pools, you can configure your network to allow for outgoing IP traffic from the controller to Cisco addresses at the following URL: http://www.cisco.com/security/pki/ NTP SNMP agent HTTPS Protocol ( or UDP) UDP UDP UDP The following table lists the ports that permit incoming IP traffic to DNA Center: 10
Prepare for Appliance Installation Table 8: Cisco DNA Center Appliance IP Traffic Port Reference Protocol ( or UDP) UDP UDP UDP Port Number 22 80 443 67 123 162 16026 Traffic Type SSH HTTP HTTPS bootps NTP SNMP SCEP Additionally, you can configure your network to allow for outgoing IP traffic from DNA Center to Cisco addresses at the following URL: http://www.cisco.com/security/pki/. DNA Center uses the IP addresses listed at the above URL to access Cisco supported certificates and trust pools. Prepare for Appliance Installation This section provides information about preparing for the Cisco DNA Center appliance installation. Unpack and Inspect the Appliance Caution When handling internal appliance components, wear an ESD strap and handle modules by the carrier edges only. Tip Keep the shipping container in case the appliance requires shipping in the future. 11
Review the Installation Warnings and Guidelines Note The chassis is thoroughly inspected before shipment. If any damage occurred during transportation or any items are missing, contact your customer service representative immediately. Step 1 Step 2 Step 3 Remove the appliance from its cardboard container and save all packaging material. Compare the shipment to the equipment list provided by your customer service representative. Verify that you have all items. Check for damage and report any discrepancies or damage to your customer service representative. Have the following information ready: Invoice number of shipper (see the packing slip) Model and serial number of the damaged unit of damage Effect of damage on the installation Review the Installation Warnings and Guidelines Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of: 40 C (104 F). Statement 1047 Warning The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device. Statement 1019 Warning This product relies on the building s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 250 V, 15 A. Statement 1005 Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 12
Review the Rack Requirements Caution To ensure proper airflow it is necessary to rack the appliances using rail kits. Physically placing the units on top of one another or stacking without the use of the rail kits blocks the air vents on top of the appliances, which could result in overheating, higher fan speeds, and higher power consumption. We recommend that you mount your appliances on rail kits when you are installing them into the rack because these rails provide the minimal spacing required between the appliances. No additional spacing between the appliances is required when you mount the units using rail kits. Caution Avoid UPS types that use ferroresonant technology. These UPS types can become unstable with systems such as the Cisco UCS, which can have substantial current-draw fluctuations due to fluctuating data traffic patterns. When you are installing an appliance, use the following guidelines: Plan your site configuration and prepare the site before installing the appliance. See the Cisco UCS Site Preparation Guide for help with recommended site planning and preparation tasks. Ensure that there is adequate space around the appliance to allow for servicing the appliance and for adequate airflow. The airflow in this appliance is from front to back. Ensure that the air-conditioning meets the thermal requirements listed in the Environmental Specifications, on page 4. Ensure that the cabinet or rack meets the requirements listed in the following "Rack Requirements" topic. Ensure that the site power meets the power requirements listed in the 770 W AC Power Supply, on page 5. If available, you can use an uninterruptible power supply (UPS) to protect against power failures. Review the Rack Requirements This topic explains the requirements for installling the appliance in standard open racks. The rack must be of the following type: A standard 19-in. (48.3-cm) wide, four-post EIA rack, with mounting posts that conform to English universal hole spacing, per section 1 of ANSI/EIA-310-D-1992. The rack post holes can be square 0.38-inch (9.6 mm), round 0.28-inch (7.1 mm), #12-24 UNC, or #10-32 UNC when you use the supplied slide rails. The minimum vertical rack space per server must be one RU, equal to 1.75 in. (44.45 mm). 13
Connect and Power On the Appliance Connect and Power On the Appliance This section describes how to power on the Cisco DNA Center appliance and assign an IP address to connect to it. Step 1 Attach a supplied power cord to each power supply in the appliance and then attach the power cord to a grounded AC power outlet. See Power Specifications, on page 5 for details. Wait for approximately two minutes to let the appliance boot into standby power mode during the first bootup. You can verify the power status by looking at the Power Status LED: Off There is no AC power present in the appliance. Amber The appliance is in standby power mode. Power is supplied only to the CIMC and some motherboard functions. Green The appliance is in main power mode. Power is supplied to all appliance components. During bootup, the appliance beeps once for each USB device that is attached to the appliance. Even if there are no external USB devices attached, there is a short beep for each virtual USB device such as a virtual floppy drive, CD/DVD drive, keyboard, or mouse. A beep is also emitted if a USB device is hot-plugged or hot-unplugged during BIOS power-on self-test (POST), or while you are accessing the BIOS Setup utility or the EFI shell. Step 2 Step 3 Connect a USB keyboard and VGA monitor to the server, using the supplied KVM cable connected to the KVM connector on the front panel. Alternatively, you can use the VGA and USB ports on the rear panel. However, you cannot use the front panel VGA and the rear panel VGA at the same time. If you are connected to one VGA connector and you then connect a video device to the other connector, the first VGA connector is disabled. Refer to the following sections for configuring and using CIMC to assign an IP address to the appliance: Configure CIMC, on page 18 Use CIMC to Configure the Appliance, on page 20 Check the LEDs When the Cisco DNA Center appliance has been started up and is running, observe the state of the front-panel and rear-panel LEDs and buttons. The following topics describe the LEDs and buttons, their colors, and the appliance power state, activity, and other important hardware status indicators that they provide. Front Panel LEDs and Buttons The following table describes the Cisco DNA Center appliance front-panel LEDs and buttons. The minimum network interface speed for the appliance should be 1 GB a second. 14
Front Panel LEDs and Buttons Table 9: Front Panel LEDs and Buttons LED Name Front Panel LEDs and Buttons Identification System status Fan status Temperature status State Off There is no AC power to the appliance. Amber The appliance is in standby power mode. Power is supplied only to the CIMC and some motherboard functions. Green The appliance is in main power mode. Power is supplied to all server components. Off The Identification LED is not in use. Blue The Identification LED is activated. Green The appliance is running in a normal operating condition. Green, blinking The appliance is performing system initialization and memory checks. Amber, steady The appliance is in a degraded operational state, which may be due to one of the following: Power supply redundancy is lost. CPUs are mismatched. At least one CPU is faulty. At least one DIMM is faulty. At least one drive in a RAID configuration failed. Amber, blinking The appliance is in a critical fault state, which may be due to one of the following: Boot failed. Fatal CPU and/or bus error is detected. Server is in an over-temperature condition. Green All fan modules are operating properly. Amber, steady One fan module has failed. Amber, blinking Critical fault, two or more fan modules have failed. Green The appliance is operating at normal temperature. Amber, steady One or more temperature sensors have exceeded a warning threshold. Amber, blinking One or more temperature sensors have exceeded a critical threshold 15
Rear Panel LEDs and Buttons LED Name Power supply status Network link activity Hard drive fault Hard drive activity State Green All power supplies are operating normally. Amber, steady One or more power supplies are in a degraded operational state. Amber, blinking One or more power supplies are in a critical fault state. Off The Ethernet link is idle. Green One or more Ethernet LOM ports are link-active, but there is no activity. Green, blinking One or more Ethernet LOM ports are link-active, with activity. Off The hard drive is operating properly. Amber The hard drive has failed. Amber, blinking The device is rebuilding. Off There is no hard drive in the hard drive sled (no access, no fault). Green The hard drive is ready. Green, blinking The hard drive is reading or writing data. Rear Panel LEDs and Buttons The following table describes the Cisco DNA Center appliance rear panel LEDs and buttons. The minimum network interface speed for the appliance is 1Gbps on 10Gb connections, and 100Mbps on 1Gb connections. Table 10: Rear Panel LEDs and Buttons LED Name Power supply fault State Off The power supply is operating normally. Amber, blinking An event warning threshold has been reached, but the power supply continues to operate. Amber, solid A critical fault threshold has been reached, causing the power supply to shut down (for example, a fan failure or an over-temperature condition). 16
Install or Replace Appliance Components LED Name Power supply AC OK 1 Gb Ethernet dedicated management link speed 1 Gb Ethernet dedicated management link status 1 Gb Ethernet link speed 1 Gb Ethernet link status 10 Gb Ethernet link speed 10 Gb Ethernet link status Identification State Off There is no AC power to the power supply. Green, blinking AC power OK, DC output not enabled. Green, solid AC power OK, DC outputs OK. Off link speed is 10 Mbps or less. Amber link speed is 100 Mbps. Green link speed is 1 Gbps. Off No link is present. Green Link is active. Green, blinking Traffic is present on the active link. Off link speed is 10 Mbps or less. Amber link speed is 100 Mbps. Green link speed is 1 Gbps. Off No link is present. Green Link is active. Green, blinking Traffic is present on the active link. Off link speed is 100 Mbps or less. Amber link speed is 1 Gbps. Green link speed is 10 Gbps. Off No link is present. Green Link is active. Green, blinking Traffic is present on the active link. Off The Identification LED is not in use. Blue The Identification LED is activated. Install or Replace Appliance Components Refer to the Cisco UCS C220 M4 Server Installation and Service Guide for information on how to install or replace the Cisco DNA Center appliance components. 17
Configure CIMC Configure CIMC After rack-mounting the appliance and connecting the network cabling, use the Cisco IMC Configuration Utility (CIMC) to assign the appliance an IP address and gateway. Step 1 Step 2 Step 3 Attach a keyboard and monitor to the USB ports on the rear panel of the appliance or by using a KVM cable and connector to access the appliance console. Plug in the power cord. Press the Power button to boot the appliance. Watch for the prompt to press F8 as shown in the CIMC boot screen. Figure 3: CIMC Boot Screen 18
Configure CIMC Step 4 During bootup, press F8 to open the CIMC Configuration Utility. The CIMC Configuration Utility screen appears. Figure 4: CIMC Configuration Utility Screen Step 5 In the Configuration Utility window, change the following fields as specified: NIC mode Select Dedicated. IP (Basic) Select IPV4. CIMC IP Enter the IP address of the CIMC. Prefix/Subnet Enter the subnet of the CIMC. Gateway Enter the Gateway address. Pref DNS Server Enter the preferred DNS server address, if available. 19
Use CIMC to Configure the Appliance NIC Redundancy None Step 6 Step 7 Press F1 to specify additional settings. Make the following changes on the Additional Settings window: For Common Properties, enter a hostname for CIMC. For Common Properties, turn off Dynamic DNS. Turn off the Factory Defaults. Enter the admin password. If you leave the password field blank, the default password is password. Enter new Port Properties or accept the default. Turn off the Port Profiles. Step 8 Step 9 Step 10 Press F10 to save the settings. Press escape to exit and reboot the server. After the settings are saved, open a browser and enter the following URL: https://cimc_ip_address where CIMC_IP_address is the IP address that you entered in Step 5. What to Do Next Continue by using CIMC to configure the appliance so that it will boot from the DNA Center ISO image stored on the appliance. See Use CIMC to Configure the Appliance, on page 20. Use CIMC to Configure the Appliance After you configure the CIMC for your Cisco DNA Center appliance, you can use CIMC to get the configuration wizard running. Before You Begin Ensure that you have connected and powered up the appliance by following the recommended procedures in this guide. Ensure that you have configured CIMC on your appliance. For information about this procedure, see Configure CIMC, on page 18. Ensure that you have your Cisco DNA Center program parameter information available and the requirements ready for deployment. For more information about these parameters, see Review Cisco DNA Center Configuration Wizard Parameters. Step 1 Use a browser and the assigned CIMC IP address to log in to the CIMC Setup Utility. The IP address was set during the CIMC configuration you performed, as explained in Configure CIMC, on page 18. 20
Use CIMC to Configure the Appliance Step 2 Step 3 The default username for the server is admin. The default password is password. Choose Macros > Static Macros > Ctrl-Alt-Del to boot the DNA Center appliance. Proceed to configure the DNA Center appliance using the configuration wizard, as explained in Configure Cisco DNA Center Using the Wizard. 21
Use CIMC to Configure the Appliance 22