Atom OD06-14 Outdoor CPE Specification

1. Product Overview 1.1 Introduction Baicells is a private, high-tech company providing disruptively-priced and technically innovative LTE wireless broadband access solutions. The Baicells solutions support fixed wireless and mobile small cells. With the vision to connect the unconnected, Baicells has introduced breakthrough technologies to LTE, like moving a complete LTE system to unlicensed spectrum and building it with an IT based architecture. With the Baicells turnkey end-to-end solutions, it becomes much easier to provide wireless internet within everyone's reach at a very low cost. These innovative solutions can be used by mobile operators, broadband access operators, cable operators, mobile virtual operators, governments, and enterprise private networks. The Baicells Atom OD06-14 (3GPP Release 10) Outdoor Customer Premise Equipment (CPE) provides superior wireless access performance and comprehensive routing capabilities to bring wireless broadband data and voice services to end-users. It converts high-speed TDD LTE signals to Wi-Fi signals on the local area network (LAN). Wireless and wired devices, including mobile phones, laptops, tablets, laptop computers, printers, and other smart devices, can access the CPE simultaneously. 1.2 Features Supports TDD LTE network access Complies with 3GPP Release 10 CAT6 standards TDD frequency bands 42 and 43 1000 Mbps Ethernet interface Convenient, simple, GUI-based local and remote Web management Built-in LTE bipolar directional high-gain antenna TR069 network management protocol Cell lock, SIM lock, and Pin lock User-friendly LED indicators Power supply with PoE Pole mount or wall mount 1

1.3 Appearance The front and back of the Baicells Atom OD06-14 (R10) CPE unit are shown in Figure 1-1. The bottom of the unit has several interfaces, as shown in Figure 1-2. The interfaces are described in Table 1-1. Figure 1-3 provides a closer view of the LEDs; they are explained in Table 1-2. Figure 1-1 Atom 14 (R10) Appearance Figure 1-2 Atom 14 (R10) Interfaces Interfaces PoE TF SIM RESET GND Table 1-1 Atom 14 (R10) Interfaces Connected to the PoE power adaptor Card slot for SD card 1.8V/3.0V USIM 2FF Press the reset button for at least 10 seconds to restore the CPE to its factory settings Ground lug. Connected to Earth by conductor. 2

Figure 1-3 Atom 14 (R10) LED Indicators Table 1-2 Atom 14 (R10) LED Indicators Identity Color Status OFF Reserved. MIU - Yellow Steady On Reserved. Blinking Reserved. LTE SIM LAN Network state OFF No LTE internet connection Blue indicator Steady On LTE internet connection SIM card status indicator Yellow 100 Mbps Ethernet indicator Yellow PWR Power indicator Yellow 1, 2, 3, 4, or 5 bars to indicate connection status and signal LTE Signal strength. The Green more bars, the stronger the signal between the CPE and a cell. Steady On The SIM card is normal Blinking The SIM card is not normal or is not inserted OFF Ethernet connection is not established. Steady On Ethernet connection is normal Blinking Data is transmitting OFF No power supply Steady On Power on All OFF Signal is too weak for the CPE to attach to the LTE network Steady On Bars will light steadily according to signal strength Scanning the LTE network Blinking The CPE is authenticating The CPE is getting an IP address from the LTE network 3

2. Technical Specifications 2.1 Basic Specifications LTE Standard 3GPP Release 10 Ethernet LAN Port One RJ-45 port 10/100/1000 auto-sensing, auto-mdx, PoE LED Indicators MIU/LTE/SIM/LAN/PWR/SIGNAL (5 BAND) USIM 1.8V/3V 2FF Restore Button Tactile button. Press the button for at least 10 seconds to restore the CPE to its factory settings Power Supply Input: Universal range 100V~240V AC Dimensions About 9.5 in (H) x 6 in (W) x 2 in (D) About 241mm * 154mm * 50mm Weight About 2 lbs (900 g) Color Pantone white C 2.2 RF Specifications LTE Mode TDD Channel Bandwidth 5 MHz / 10 MHz / 15 MHz / 20 MHz MAX Output Power 23 ± 2dBm/TX Ant * 2 TXRX 2T2R a 2T4R b Frequency Bands 42: 3400 MHz ~ 3600 MHz 43: 3600 MHz ~ 3800 MHz Antenna Gain 14 dbi @ 2T2R 11 dbi @ 2T4R Wi-Fi Standard 802.11b/g/n a EG7010B-M2 supported b EG7010D-M2 supported 4

2.3 Software Specifications Language Settings Network Mode SIM Network Connection Setup LTE Scan Mode VPN NAT Statistics English Bridge / NAT PIN management SIM lock Create, delete, and edit APNs Set up dial-up connection automatically Set up dial-up connection manually Full band Cell lock Band / Frequency preferred Support L2TP tunnel mode Support VxLAN tunnel mode Port forwarding Port trigger DMZ UPnP LAN link status Transmit / Receive traffic Run time 2.4 Device Management Maintenance TR069 Port mirror Syslog Diagnostics Date & Time setting Reset Restore factory settings Restore / Back up configuration file Local upgrade Can enable or disable TR069 management Can enable or disable the port mirror function Syslog function - can send logs to the PC via LAN Ping and trace route 5

2.5 Environmental Specifications Operating Temperature -40 F to 131 F -40 ~ 55 Storage Temperature -40 F to 158 F -40 ~ 70 Operating Humidity 5% ~ 95% 6

Appendix A Model List Model Name EG7010B-M2 EG7010D-M2 BaiCE-EG7010B-M2 LTE CPE ODU, B42/B43, CAT6, 2T2R, MTK7620A+GDM7243QT, 1GE, PoE 24V, IP65 BaiCE-EG7010D-M2 LTE CPE ODU, B42/B43, CAT6, 2T4R, MTK7620A+GDM7243QT, 1GE, PoE 24V, IP65 7