PB600/H1 Embedded & Industrial PCs INTERNATIONAL PRODUCTS AND CONFIGURATIONS PB600/H1 BASIC SYSTEM PB600/H1 basic configuration Intel Celeron M 1.5GHz 256 MB RAM kit HDD 40GB 2.5" SATA No FDD Power supply 220V/AC CPU RAM MEMORY HARD DISK POWER SUPPLY ETHERNET PORTS OPTIONS Intel Celeron M 1.5 GHz, 400MHz front side bus, 1MB cache socket 478 μfc-pga Intel Pentium M 1.73 GHz, 533MHz front side bus, 2MB cache socket 478 μfc-pga Intel Pentium M 2 GHz, 533MHz front side bus, 2MB cache socket 478 μfc-pga 256 MB 1 SODIMM module DDR2 PC4300 512 MB 1 SODIMM module DDR2 PC4300 1 GB 1 SODIMM module DDR2 PC4300 2 GB 2 SODIMM modules DDR2 PC4300, 1 GB each No Kit Hard Disk Kit HDD 40GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 60GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 80GB 2.5" SATA 5400rpm, 8 MB buffer 110 220V/AC 140W, autoranging 18 36V/DC 140W, autoranging 2 x 10/100Mbit RJ45 connector 1 x 10/100Mbit, 1 x 10/100/1000Mbps RJ45 connector Additional serial port (3rd) RS-232/422/485 DB15 male connector > see annotation 1 Additional serial port (3rd) RS-232/422/485 RS-422/485 optoisolated DB15 male connector > see annotation 1 Parallel port SPP-EPP-ECP bidirectional DB25 male connector > see annotation 1 Fieldbus module NETCORE > see annotation 2 Warranty extension to 18 months + 1 month exemption on basic system and its variants Warranty extension to 24 months + 1 month exemption on basic system and its variants ANNOTATIONS 1: Additional serial ports RS-232/422/485 and parallel port can be installed alternatively one to the other only 2: For fieldbus module NETCORE specifications see page 107 of Poducts and Configurations dated November 8th, 2006 PB600/H1 BASIC SYSTEM TECHNICAL SPECIFICATIONS Case DIN rail mount Overall dimensions & weight See details on the rear Motherboard "All-In-One" type ASEM 921 with watchdog timer, hardware system for temperature and voltage board diagnostics Video controller Integrated on-board, VGA standard analog interface (external port) and LVDS digital interface for TFT LCD (internal socket) Simul Scan Video memory (shared) 64/128 MB selectable in system setup RAM memory sockets 2 x SODIMM modules, 200 pin RAM memory DDR2-533 type PC4300 low profile Minimum system memory 256 MB Maximum system memory 2 GB Mass storage interfaces 1 x FDD 1 x ATA/100 (Master, Slave) 2 x SATA/150 Solid State Disk interface 1 x Compact Flash type II slot, rear access On-board options predisposition Additional serial port (3rd) predisposition (see OPTIONS) Bus expansions slots Not available Rear access interfaces 2 x PS/2 (K/M) 2 x Ethernet 10/100Mbit RJ45 connector 4 x USB (2 x 2.0) standard-a connector 1 x analog VGA DB15 female connector Rear access serial interfaces 2 x RS-232 DB9 male connector Fieldbus interfaces NETCORE fieldbus module predisposition (see OPTIONS) > see annotation 2 at previous page Environmental specifications Operating temperature: 0 +50 C without HDD, 0 +45 C with HDD Storage temperature: -20 +60 C Humidity: 80% (non-condensing) Standard warranty 12 months + 1 month exemption warranty management by ASEM headquarters
PB600/H1 PB600/H1-TE OVERALL DIMENSIONS (mm) FRONT VIEW REAR VIEW SIDE VIEW 34.5 326.5 69.5 355 14 14 34.5 10 1 236 173.5 236.5 238 26 13 13 352 Weight 4.8kg 22 311 22 60.5
PB600/H3 Embedded & Industrial PCs INTERNATIONAL PRODUCTS AND CONFIGURATIONS PB600/H3 BASIC SYSTEM PB600/H3 basic configuration Intel Celeron M 1.5GHz 256 MB RAM kit HDD 40GB 2.5" SATA No FDD Power supply 220V/AC 2 slots PCI CPU RAM MEMORY HARD DISK POWER SUPPLY EXPANSION SLOTS ETHERNET PORTS FDD/CD/DVD REAR ACCESS OPTIONS Intel Celeron M 1.5 GHz, 400MHz front side bus, 1MB cache socket 478 μfc-pga Intel Pentium M 1.73 GHz, 533MHz front side bus, 2MB cache socket 478 μfc-pga Intel Pentium M 2 GHz, 533MHz front side bus, 2MB cache socket 478 μfc-pga 256 MB 1 SODIMM module DDR2 PC4300 512 MB 1 SODIMM module DDR2 PC4300 1 GB 1 SODIMM module DDR2 PC4300 2 GB 2 SODIMM modules DDR2 PC4300, 1 GB each No Kit Hard Disk Kit HDD 40GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 60GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 80GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 80GB 3.5" SATA 7200rpm, 8 MB buffer Kit HDD 160GB 3.5" SATA 7200rpm, 8 MB buffer 110 220V/AC 140W, autoranging 18 36V/DC 140W, autoranging 2 x PCI half size on riser card 2 x PCI half size on riser card with predisposition for 32-bit, 512KB max NOVRAM 1 x PCI, 1 x PCI-Express x1 format half size on riser card 2 x 10/100Mbit RJ45 connector 1 x 10/100Mbit, 1 x 10/100/1000Mbps RJ45 connector Kit FDD 3.5" 1.44 MB H=1" white bezel > see annotation 1 Kit CD-ROM E-IDE 24x Slim H=0.5" black bezel Kit COMBO DVD-ROM E-IDE 24x / CD-RW 24x10x24x Slim H=0.5" black bezel Kit DVD-RW E-IDE 8x4x24x10x Slim H=0.5" black bezel Kit FDD 3.5" 1.44 MB Slim + CD-ROM E-IDE 24x Slim H=1" black bezel Kit FDD 3.5" 1.44 MB Slim + COMBO E-IDE DVD-ROM 24x / CD-RW 24x10x24x Slim H=1" black bezel Kit FDD 3.5" 1.44 MB Slim + DVD-RW E-IDE 8x4x24x10x Slim H=1" black bezel Additional serial port (3rd) RS-232/422/485 DB15 male connector > see annotation 1 Additional serial port (3rd) RS-232/422/485 RS-422/485 optoisolated DB15 male connector > see annotation 1 Parallel port SPP-EPP-ECP bidirectional DB25 male connector > see annotation 1 Fieldbus module NETCORE > see annotation 2 Warranty extension to 18 months + 1 month exemption on basic system and its variants Warranty extension to 24 months + 1 month exemption on basic system and its variants ANNOTATIONS 1: Standard height (1") FDD can be installed as an alternative to the slim units only 2: Additional serial ports RS-232/422/485 and parallel port can be installed alternatively one to the other only 3: For fieldbus module NETCORE specifications see page 107 of Poducts and Configurations dated November 8th, 2006 TECHNICAL SPECIFICATIONS: see next page
PB600/H3 PB600/H3 BASIC SYSTEM TECHNICAL SPECIFICATIONS Case DIN rail mount Overall dimensions & weight See details on the rear Motherboard "All-In-One" type ASEM 921 with watchdog timer, hardware system for temperature and voltage board diagnostics Video controller Video memory (shared) Integrated on-board, VGA standard analog interface (external port) and LVDS digital interface for TFT LCD (internal socket) Simul Scan 64/128 MB selectable in system setup RAM memory sockets 2 x SODIMM modules, 200 pin RAM memory DDR2-533 type PC4300 low profile Minimum system memory 256 MB Maximum system memory 2 GB Mass storage interfaces 1 x FDD 1 x ATA/100 (Master, Slave) 2 x SATA/150 Solid State Disk interface 1 x Compact Flash type II slot, rear access On-board options predisposition Additional serial port (3rd) predisposition (see OPTIONS) Bus expansions slots 2 x PCI Rear access interfaces 2 x PS/2 (K/M) 2 x Ethernet 10/100Mbit RJ45 connector 4 x USB (2 x 2.0) standard-a connector 1 x analog VGA DB15 female connector Rear access serial interfaces 2 x RS-232 DB9 male connector Fieldbus interfaces NETCORE fieldbus module predisposition (see OPTIONS) > see annotation 3 at previous page Environmental specifications Operating temperature: 0 +50 C without HDD, 0 +45 C with HDD Storage temperature: -20 +60 C Humidity: 80% (non-condensing) Standard warranty 12 months + 1 month exemption warranty management by ASEM headquarters PB600/H3-TE OVERALL DIMENSIONS (mm) FRONT VIEW REAR VIEW SIDE VIEW 34.5 326.5 69.5 355 14 14 38 101 63 236 173.5 242 26 13 13 352 weight 6.4kg 22 311 22 117
PB600/H4 Embedded & Industrial PCs INTERNATIONAL PRODUCTS AND CONFIGURATIONS PB600/H4 BASIC SYSTEM PB600/H4 basic configuration Intel Celeron M 1.5GHz 256 MB RAM kit HDD 40GB 2.5" SATA No FDD Power supply 220V/AC 4 slots PCI CPU RAM MEMORY HARD DISK POWER SUPPLY EXPANSION SLOTS ETHERNET PORTS FDD/CD/DVD REAR ACCESS OPTIONS Intel Celeron M 1.5 GHz, 400MHz front side bus, 1MB cache socket 478 μfc-pga Intel Pentium M 1.73 GHz, 533MHz front side bus, 2MB cache socket 478 μfc-pga Intel Pentium M 2 GHz, 533MHz front side bus, 2MB cache socket 478 μfc-pga 256 MB 1 SODIMM module DDR2 PC4300 512 MB 1 SODIMM module DDR2 PC4300 1 GB 1 SODIMM module DDR2 PC4300 2 GB 2 SODIMM modules DDR2 PC4300, 1 GB each No Kit Hard Disk Kit HDD 40GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 60GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 80GB 2.5" SATA 5400rpm, 8 MB buffer Kit HDD 80GB 3.5" SATA 7200rpm, 8 MB buffer Kit HDD 160GB 3.5" SATA 7200rpm, 8 MB buffer 110 220V/AC 140W, autoranging 18 36V/DC 140W, autoranging 4 x PCI half size on riser card 4 x PCI half size on riser card with predisposition for 32-bit, 512KB max NOVRAM 3 x PCI, 1 x PCI-Express x1 format half size on riser card 2 x 10/100Mbit RJ45 connector 1 x 10/100Mbit, 1 x 10/100/1000Mbps RJ45 connector Kit FDD 3.5" 1.44 MB H=1" white bezel > see annotation 1 Kit CD-ROM E-IDE 24x Slim H=0.5" black bezel Kit COMBO DVD-ROM E-IDE 24x / CD-RW 24x10x24x Slim H=0.5" black bezel Kit DVD-RW E-IDE 8x4x24x10x Slim H=0.5" black bezel Kit FDD 3.5" 1.44 MB Slim + CD-ROM E-IDE 24x Slim H=1" black bezel Kit FDD 3.5" 1.44 MB Slim + COMBO E-IDE DVD-ROM 24x / CD-RW 24x10x24x Slim H=1" black bezel Kit FDD 3.5" 1.44 MB Slim + DVD-RW E-IDE 8x4x24x10x Slim H=1" black bezel Additional serial port (3rd) RS-232/422/485 DB15 male connector > see annotation 1 Additional serial port (3rd) RS-232/422/485 RS-422/485 optoisolated DB15 male connector > see annotation 1 Parallel port SPP-EPP-ECP bidirectional DB25 male connector > see annotation 1 Fieldbus module NETCORE > see annotation 2 Warranty extension to 18 months + 1 month exemption on basic system and its variants Warranty extension to 24 months + 1 month exemption on basic system and its variants ANNOTATIONS 1: Standard height (1") FDD can be installed as an alternative to the slim units only 2: Additional serial ports RS-232/422/485 and parallel port can be installed alternatively one to the other only 3: For fieldbus module NETCORE specifications see page 107 of Poducts and Configurations dated November 8th, 2006 TECHNICAL SPECIFICATIONS: see next page
PB600/H4 PB600/H4 BASIC SYSTEM TECHNICAL SPECIFICATIONS Case Overall dimensions & weight Motherboard Video controller Video memory (shared) RAM memory sockets RAM memory Minimum system memory Maximum system memory Mass storage interfaces Solid State Disk interface On-board options predisposition Bus expansions slots Rear access interfaces Rear access serial interfaces Fieldbus interfaces Environmental specifications Standard warranty DIN rail mount See details on the rear "All-In-One" type ASEM 921 with watchdog timer, hardware system for temperature and voltage board diagnostics Integrated on-board, VGA standard analog interface (external port) and LVDS digital interface for TFT LCD (internal socket) Simul Scan 64/128 MB selectable in system setup 2 x SODIMM modules, 200 pin DDR2-533 type PC4300 low profile 256 MB 2 GB 1 x FDD 1 x ATA/100 (Master, Slave) 2 x SATA/150 1 x Compact Flash type II slot, rear access Additional serial port (3rd) predisposition (see OPTIONS) 4 x PCI 2 x PS/2 (K/M) 2 x Ethernet 10/100Mbit RJ45 connector 4 x USB (2 x 2.0) standard-a connector 1 x analog VGA DB15 female connector 2 x RS-232 DB9 male connector NETCORE fieldbus module predisposition (see OPTIONS) > see annotation 3 at previous page Operating temperature: 0 +50 C without HDD, 0 +45 C with HDD Storage temperature: -20 +60 C Humidity: 80% (non-condensing) 12 months + 1 month exemption warranty management by ASEM headquarters PB600/H4-TE OVERALL DIMENSIONS (mm) FRONT VIEW REAR VIEW SIDE VIEW 34.5 326.5 69.5 355 14 14 38 63 236 173.5 242 26 13 13 352 Weight 8kg 22 311 22 117