9//05 9L-00 Rev. A TT0 Quick Reference Guide S4M Quick Reference Guide External View Use this guide to operate your printer on a daily basis. For more detailed information, refer to the TT0 User Guide or visit idsolutions.htamericas.com. Use this guide to operate your printer on a daily basis. For more detailed information, refer to the S4M User Guide. Figure Exterior of Printer Front Rear 4 Control panel Media door Power switch (O = Off, I = On) 4 AC power connector TT0 Printed Quick Reference on Guide chlorine-free recycled pape 005 ZIH Corp. All product names and numbers idsolutions.htamericas.com are Zebra trademarks, and Zebra and the Zebra logo are registered trademarks of ZIH Corp. All rights reserved.
0 Load Ribbon Driver Installation Printer Components Driver Installation Remove the Ribbon Printer Components Figure shows the components inside the media compartment of your printer. Depending on To remove used ribbon, complete these steps: USB Driver Installation ONLY installed options, your printer may look slightly different. (Look. at Help TT0 CD more help.) If TT0 the ribbon Install has not run out,on cutyour or break it before thefor ribbon take-up spindle. Figure directly S4M Components. TurnCaution on your TT0 printer andplug the Printer USB cord into take-up the backspindle. of yourdoing printer Do not cut the ribbon on the ribbon soand mayyour computer. damage the spindle.. Welcome to the Found New Hardware Wizard will appear. Select Yes, this time only. Then, click Next.. Select Install from a list or specific location (Advanced), then click Next. 4. Select Don t Search, I will choose the driver to install. Then, click 5 Next. 5. Click Have Disk... 6. Click Browse... 7. Search for the TT0 Driver Folder, and then click Open. 8. Click OK. 9. Highlight the TT0 and click Next. 4 0. Click Continue Anyway. 6. Click Finish. 7 Hardware will appear if you installed your driver correctly.. Found New 8 DriverInstallation (Look at TT0 Install Help on your TT0 CD for more help.)... 4. 5. 6. 7. 8. 9. 0.... 4. 5. 6.. Squeeze the ribbon Open your TT0 CD.against the ribbon take-up spindle tension blades (). At the same turn the ribbon Opentime, the TT0 Drivertake-up folder.spindle release knob counterclockwise (). In the TT0 click thetake-up Setup icon. The tensiondriver bladesfolder, collapsedouble into the ribbon spindle, loosening the ribbon. Welcome to the Printer Setup Wizard. Click Next. In the Printer Select Window, highlight the TT0. Then, click Next. Hardware Installation window will appear. Click Continue Anyway. is connected to your computer. (Note: USB needs to be Select which port your printer installed differently; SEE ABOVE.) Then click Next. Select a name for your printer (default is TT0.) Click Next. 0 9 Welcome to the Configuration Wizard. Click Next. Label Setup should have these settings: Printhead assembly Media supply guide.00 Label Size: X 4.00 (5.08 cm X 0.5 cm) 7 Ribbon supply spindle* Fanfold media slot Orientation: Portrait 8 Unit of Measurement: Centimeters Control panel Dancer assembly 9. Slide the ribbon off of the ribbon take-up spindle. Click Next. Ribbon take-up spindle* Media guide 4 0 Top Adjustments should Media doorbe 0. Click Next. Printhead release latch 5 Dispense6Mode should be Rewind Printed Labels. Click Next. Media supply hanger Media*Type should be Thermal Transfer. Click Next. Present only on printers that have the Thermal Transfer option installed. Media Tracking should be Non Continuous. Click Next. Click Finish. Your Printer is now installed. TT0 Quick Reference Guide 9//05 9L-00 Rev. A S4M Quick Reference Guide idsolutions.htamericas.com 9L-009//05 Rev. A
0 Load Ribbon Driver Settings Remove the Ribbon To remove The driverused needsribbon, to be setcomplete up as a thermal thesetransfer steps:printer. The driver should be set up to rewind printed labels, which will disable TOF backup.. If the ribbon out, cut or break before the ribbon spindle. The driver shouldhas benot set run up to calibrate uponithead close. This istake-up easier than doing a memory dump, and helps make sure labels will print in alignment. Caution Do notlabel cut the directly on the ribbon Doing so mayor Printer should sense gap.ribbon Use transmissive sensor,take-up except spindle. when using TipTags damage the spindle. ShrinkTrak. (When using TipTags or ShrinkTrak, press Menu on the front panel, and cycle until sensor select appears on LCD. Choose reflective. Also, physically adjust the sensor to sense the center gap space. Then, in the printer menu, save the settings. When finished printing TipTags or ShrinkTrak, go back to the printer menu and reselect the transmissive sensor.) To change from reflective sensor to transmissive sensor: () Press the right arrow softkey 5 times. () Press the up arrow to cycle between reflective and transmissive sensor. () Press the Menu softkey. (4) Press the Enter softkey to make changes.. Squeeze the ribbon against the ribbon take-up spindle tension blades (). At the same time, turn the ribbon take-up spindle release knob counterclockwise (). The tension blades collapse into the ribbon take-up spindle, loosening the ribbon.. Slide the ribbon off of the ribbon take-up spindle. TT0 Quick Reference Guide 9L-00 Rev. A S4M Quick Reference Guide idsolutions.htamericas.com 9//05
Printer Components 4 Printer Components Figure shows the components inside the media compartment of your printer. Depending on installed options, your printer may look slightly different. Figure TT0 S4M Printer Components 5 4 6 7 8 0 9 Printhead assembly 7 Media supply guide Ribbon supply spindle* 8 Fanfold media slot Control panel 9 Dancer assembly 4 Ribbon take-up spindle* 0 Media guide 5 Media door Printhead release latch 6 Media supply hanger * Present only on printers that have the Thermal Transfer option installed. 9//05 TT0 Quick Reference Guide S4M Quick Reference Guide idsolutions.htamericas.com 9L-00 Rev. A
54 Load Media Load Media Use the instructions in this section to load roll media in Tear-Off mode (Figure 4). For instructions for loading fanfold media or for loading in different print modes, refer to the User Guide. Figure 4 Tear-Off Mode Media Path To Load Roll Media in Tear-Off Mode, complete these steps:. Remove and discard one full revolution of labels or tags and any liner. Labels Tag Stock. Flip down the media supply guide. 9L-00 TT0 Quick Rev. Reference A Guide S4M Quick Reference Guide idsolutions.htamericas.com 9//05
Load Media 65. Place the roll of media on the media supply hanger. Push the roll as far back as it will go. 4. Flip up the media supply guide, and then slide it in until it touches, but does not restrict, the edge of the roll. 5. Press the printhead release latch to open the printhead assembly. Lift the printhead until it latches open. 9//05 TT0 Quick Reference Guide S4M Quick Reference Guide idsolutions.htamericas.com 9L-00 Rev. A
76 Load Media 6. Slide out the media guide. 7. Feed the media under the dancer assembly (), through the slot in the transmissive sensor (), and under the ribbon sensor (). Push the media to the back of the transmissive sensor. 8. Slide in the media guide until it just touches the edge of the media. 9L-00 TT0 Quick Rev. Reference A Guide S4M Quick Reference Guide idsolutions.htamericas.com 9//05
Load Ribbon 87 9. Close the printhead assembly. Load Ribbon 0. If the printer is paused (the PAUSE light is blinking), press PAUSE to enable printing. This section applies only to printers that have the Thermal Transfer option installed. Note Always use ribbon that is wider than the media to protect the printhead from wear. For direct thermal printing, do not load ribbon in the printer. Figure 5 Ribbon Path 4 Printhead assembly Ribbon supply spindle Ribbon take-up spindle 4 Tension blades 9//05 TT0 Quick Reference Guide S4M Quick Reference Guide idsolutions.htamericas.com 9L-00 Rev. A
98 Load Ribbon To load ribbon, complete these steps:. Press the printhead release latch to open the printhead assembly. Lift the printhead until it latches open.. Orient the ribbon with the loose end unrolling clockwise.. Place the ribbon roll onto the ribbon supply spindle () and push it all the way back. 9L-00 TT0 Quick Rev. Reference A Guide S4M Quick Reference Guide idsolutions.htamericas.com 9//05
Load Ribbon 0 9 4. Pull the end of the ribbon under the printhead assembly () and out the front of the printer. 5. Close the printhead assembly. 6. Wind the ribbon clockwise onto the ribbon take-up spindle (). 9//05 TT0 Quick Reference Guide S4M Quick Reference Guide idsolutions.htamericas.com 9L-00 Rev. A
0 Load Ribbon Remove the Ribbon To remove used ribbon, complete these steps:. If the ribbon has not run out, cut or break it before the ribbon take-up spindle. Caution Do not cut the ribbon directly on the ribbon take-up spindle. Doing so may damage the spindle.. Squeeze the ribbon against the ribbon take-up spindle tension blades (). At the same time, turn the ribbon take-up spindle release knob counterclockwise (). The tension blades collapse into the ribbon take-up spindle, loosening the ribbon.. Slide the ribbon off of the ribbon take-up spindle. 9L-00 TT0 Quick Rev. Reference A Guide S4M Quick Reference Guide idsolutions.htamericas.com 9//05