Smart Hub Intelligent Energy Management and IoT Hub Unit (CT200i) General Dimension and weight 202.73 x 267.45 x 60 mm, 700 gm Dimension with standard cover 268 x 204 x 56 mm Dimension with weatherproof cover 305 x 260 x 76 mm Mounting and weight Wall mounted enclosure, 1 Kg Enclosure Weatherproof, high impact GF ABS Operating temperature -20 C to 55 C Operating voltage 100-240VAC General Information Telecommunication compliance ACMA Section 376 of the Telecommunications Act 1997 AS/CA S042.1: 2011 AS/ACIF S042.3: 2005 AS/NZS 60950.1: 2011 Functions Remote control and monitoring with debug features Timers User configurable timer based control Firmware upgrade Over the air (OTA) programmable Time Accurate system clock (sync with server every hour) Unique Device identification number (DIN) Device remote addressable Compatibility Backbone compatible with static and dynamic IP addressing Data transmission Secure carbontrack MDT protocol
Electrical Parameters Electricity phase Single and three phase (3 phase 4 wire) Power direction Measures both import and export Solar Support Yes (shareable among total of 3 current clamps) Monitoring Active power Both Watt and Watt-hour in all phases Reactive power Both VAR and VARh in all phases Power factor Yes (0 to 1 PF) in all phases Device specific parameters Specific monitoring support from ZigBee and Z-Wave Compatibility Electrical hot water Support up to 2 electrical hot water/geysers Manual control / configurable switch on timers Peak load timer for efficient heating Solar thermal controller Smart and better energy efficient Temperature differential based control Holiday mode enable/disable feature Anti-freeze protection technology HVAC (Heating, Venting and Air-Conditioning) Support up to 3 HVAC system Temperature based control Solenoid value Shut-off valve control for hot water units ZigBee/Z-Wave capability On-board ZigBee and external optional Z-Wave support General switching, timer and Power measurement Device specific features (door lock, alarm, detectors, etc.) Green circuit Enabled green circuit feature to maximize solar use Wired future expansion Any device supporting I2C or RS232 communication Wireless future expansion ZigBee router implementation (e.g. CTZB485)
Control Relay control Enabled through three onboard relays Relay port voltage and rated current 12 V DC, 200 ma Relay output voltage and rated current 240 VAC, 30 A Wireless device control Enabled through ZigBee and Z-Wave User Interface Switches Two switches to select between analog or digital sensors Button One button to enable relay override LED indicator Green LED for power and Red LED for fault indication Online Interface Online dashboard and control panel Mobile App Android and IOS compatible applications Sensor Voltage sensor and type 85 V to 264 V line-to-neutral, on board or line to line AC voltage sensing Current sensor and type 60 A standard sensor (60 A to 2000 A options), off board Temperature sensor 2 Analog and up to 8 digital, -55 C to 125 C Water flow sensor 1 L/min to 60 L/min Leak sensor Water leak detector of geyser dip tray, alert triggered Earth fault alarm Supports electrical fault leakage Communication and Radio Backbone service 2G/3G telecommunication (carbontrack MDT backbone) Local wireless network ZigBee HA 1.2 and Z-Wave Local wired platform Serial UART for debug purpose GSM frequency and max RF power 850/900 MHz: 2W, 1800/1900 MHz: 1W UMTS frequency and max RF power 800/850/2100: 0.25W
Data Management Internal storage 4kB Data post Configurable data post to server (15 minute) carbontrack server Main data center (high level of availability and redundancy) Data backup in server Archived up to 5 years (standard package) Power Management AC power rating 100V to 250 VAC, 55 VA Optional DC power 5 to 24 V DC Battery support 3.7 V/ 1250 mah, 4.62 wh Battery backup 24-48 hours (subjected to network signal strength) Battery type Lithium ion
Standard Casing 56mm 204mm 268mm Waterproof Cover 260mm 76mm 305mm