LED Lamps & Accessories Lighting Guide

LED Lamps & Accessories Lighting Guide 1

LED Lamps & Accessories Lighting Guide Table of Contents Mogul Base LED... 3 Medium Base... 13 Linear LED... 15 Photocells... 21 2

Mogul-Base Area LED Replacement Lamp 3000K, 4000K / 80W, 110W / 125 Lm/W Specification Sheet Project: Catalog#: Approved by: LEDMAR No Ballast needed (UL Type B) Internal driver/line voltage lamp Remove ballast from fixture Features 120 Lm/W Power Factor: >0.9 CCT: 3000K or 4000K; CRI: >80 Long Life: 10 years Operating temperature range: -40 C (-40 F) to +60 C (140 F) IP64 Design - Driver is fully potted with silicone. Waterproof, dust proof, and bug proof Flame retardant material Suitable for totally enclosed fixtures Built in 6kV surge protection UL/cUL Listed, UL Classified 120-277 VAC, 50/60Hz Non-dimming Warranty: 5 Years No Fan Applications LEDMAR lamps are designed as an energy saving LED replacement for retrofitting HID area luminaires. Shoe Box Ordering Information Catalog # Lumens CCT Watts Lm/W Cover Base Replacement LEDMAR-3080-MV LEDMAR-4080-MV LEDMAR-30110-MV LEDMAR-40110-MV 9,600 13,200 3000K 4000K 3000K 4000K 80W 110W 120 Clear EX39 250W HPS or MH 400W HPS or MH Specifications subject to change without notice. Page 1 of 2 Rev: 10/4/2018 3

Specification Sheet LEDMAR Dimensions (in) 5.0 5.0 125.51 125.5 1 5.0 125.51 5.0 125.51 118.51 228.7 2 111.45 69.83 69.83 2.75 221. 23 221.23 118.51 111.45 228.72 69.8 2.75 3 69.83 281.73 11.1 281.73 4.7 4.7 118.51 118.51 9.0 4.4 2.75 8.7 8.7 4.7 4.4 2.75 11.1 4.7 9.0 80W 110W LEDMAR vs. Common Lamp Sizes Lamp Base L (in.) D (in.) LEDMAR-XX80-MV (closed) 4.4 8.8 LEDMAR-XX80-MV (open) 9.0 EX39 LEDMAR-XX110-MV (closed) 4.4 11.2 LEDMAR-XX110-MV (open) 9.0 LU150/55 7.75 2.94 LU400 9.65 2.25 MH250/U E39 8.31 3.5 MH400/U 11.5 4.6 H37KB-250 8.25 3.5 H33CD-400 11.5 4.6 REPLAC E Accessories (sold seperately) Mogul Socket LH-MOE-01 Surge Protector 20kV, 10kA HL-LSP10GI277P Twist lock long life photocontrol Multi-volt, fail-on, 8A at 120V and 5A at 277V HI-LL-127-15-BK-12 Specifications subject to change without notice. Page 2 of 2 Rev: 10/4/2018 4

Mogul-Base LED High Bay Replacement Lamp 3000K, 4000K / 115W / 125-130 Lm/W Specification Sheet Project: Catalog#: Approved by: LEDMBR No Ballast needed (UL Type B) Internal driver/line voltage lamp Remove ballast from fixture Applications LEDMBR lamps are designed as an energy saving LED replacement for retrofitting HID high bay and garage luminaires. Features Retrofit to existing 400W HID High Bay fixtures in warehouse or garage applications 125-130 Lm/W Power Factor: >0.9 CCT: 3000K or 4000K; CRI: >80 Long Life: 10 years Operating temperature range: -40 C (-40 F) to +60 C (140 F) Flame retardant material Suitable for totally enclosed fixtures Built in 6kV surge protection UL/cUL Listed, UL Classified 120-277 VAC, 50/60Hz Non-dimming Warranty: 5 Years No Fan High Bay Ordering Information Catalog # Lumens CCT Watts Lm/W Cover Base Replacement LEDMBR-30115-MV 14,375 3000K 125 115W LEDMBR-40115-MV 14,950 4000K 130 Clear EX39 400W HPS or MH Specifications subject to change without notice. Page 1 of 2 Rev: 10/4/2018 5

Specification Sheet LEDMBR Dimensions (in) 8.0 LEDMHR vs. Common Lamp Sizes 8.1 Lamp Base L (in.) D (in.) LEDMBR-XX115-MV EX39 8.1 8.0 LU250 LU400 9.658. 2.25 MH250/U E39 8.31 3.5 MH400/U 11.5 4.6 H37KB-250 8.25 3.5 Accessories (sold seperately) Specifications subject to change without notice. Mogul Socket LH-MOE-01 Surge Protector 20kV, 10kA HL-LSP10GI277P Page 2 of 2 Rev: 10/4/2018 6

Mogul-Base High Wattage LED Replacement Lamp 3000K, 4000K / 80W, 100W / 135 Lm/W Specification Sheet Project: Catalog#: Approved by: LEDMHR Applications No Ballast needed (UL Type B) Internal driver/line voltage lamp Remove ballast from fixture LEDMHR lamps are designed as an energy saving LED replacement for retrofitting high wattage HID post top and tear drop fixtures. Features 135 Lm/W Power Factor: >0.9 CCT: 3000K or 4000K; CRI: >80 Long Life: 10 years Operating temperature range: -40 C (-40 F) to +60 C (140 F) IP64 Design - Driver is fully potted with silicone. Waterproof, dust proof, and bug proof Flame retardant material Suitable for totally enclosed fixtures Built in 6kV surge protection UL/cUL Listed, Classified 120-277 VAC, 50/60Hz Non-dimming Warranty: 5 Years No Fan Shoe Box High Bay Acorn Tear Drop Ordering Information Catalog # Lumens CCT Watts Lm/W Cover Base Replacement LEDMHR-3080-MV LEDMHR-4080-MV LEDMHR-30100-MV LEDMHR-40100-MV 10,800 13,500 3000K 4000K 3000K 4000K 80W 100W 135 Clear EX39 250W HPS or MH 400W HPS or MH Specifications subject to change without notice. Page 1 of 2 Rev: 10/4/2018 7

Specification Sheet LEDMHR Dimensions (in) LEDMHR vs. Common Lamp Sizes 5.07 5.07 Lamp Base L (in.) D (in.) LEDMHR-XX80-MV 11.5 5.07 EX39 LEDMHR-XX100-MV 12.7 LU150/55 LU250 7.75 2.94 LU400 9.658. 2.25 3.5 MH250/U E39 8.31 3.5 MH400/U 11.5 4.6 H37KB-250 8.25 3.5 H33CD-400 11.5 4.6 11.5 12.7 80W 100W Accessories (sold seperately) Mogul Socket LH-MOE-01 Surge Protector 20kV, 10kA HL-LSP10GI277P Twist lock long life photocontrol Multi-volt, fail-on, 8A at 120V and 5A at 277V HI-LL-127-15-BK-12 Specifications subject to change without notice. Page 2 of 2 Rev: 10/4/2018 8

Specification Sheet Mogul-Base LED Replacement Lamp 3000K, 4000K / 30W, 40W, 50W / 125 Lm/W Project: Catalog#: Approved by: LEDMR No Ballast needed (UL Type B) Internal driver/line voltage lamp Remove ballast from fixture Features 125 Lm/W 360 Beam Angle Power Factor: >0.9 CCT: 3000K or 4000K; CRI: >80 Long Life: 10 years Operating temperature range: -30 to +60 C IP65 Design - Driver is fully sealed with heat sink silicone Waterproof, dust proof, and bug proof Flame retardant material UL/cUL Listed, UL Classified 120-277 VAC, 50/60Hz Built-in 4kV surge protection Non-dimming Warranty: 5 Years Applications Wallpack Posttop Posttop Acorn Ball Garage Light Visit www.designlights.org for the Qualified Products List Pendant Floodlight Ordering Information Catalog # Lumens CCT Watts Lm/W Cover Base* Replacement LEDMR-3030-MV 3750 3000K 30W 125 Slight Frost E39 Mogul 70W HID LEDMR-4030-MV 3750 4000K 30W 125 Slight Frost E39 Mogul 70W HID LEDMR-4040-MV 5000 4000K 40W 125 Slight Frost E39 Mogul 100W HID LEDMR-3050-MV 6250 3000K 50W 125 Slight Frost E39 Mogul 175W HID LEDMR-4050-MV 6250 4000K 50W 125 Slight Frost E39 Mogul 175W HID *Will not fit Ex39 (Pink) socket Specifications subject to change without notice. Non-stock item. Call for lead times 9 Page 1 of 2 Rev: 10/4/2018

Specification Sheet Mogul-Base LED Replacement Lamp 3000K, 4000K / 30W, 40W, 50W / 125 Lm/W Project: Catalog#: Approved by: LEDMR After Dimensions Φ 3.37 Φ 83 mm will replace 125 lm/w 360º beam angle Flame retardant material IP65 waterproof design 10.23 260 mm LEDMR vs. Common Lamp Sizes Lamp Base L (in.) D (in.) LEDMR-XXXX-MV E39 (default) 10.23 w/ medium base adapter 11.50 3.27 LU100 LU150/55 7.75 2.94 MH150/U E39 8.31 MH175/U H39KB-175 8.25 H37KC-175/DX 3.5 Visit www.designlights.org for the Qualified Products List Accessories (sold seperately) Mogul Socket LH-MOE-01 Surge Protector 20kV, 10kA HL-LSP10GI277P Twist lock long life photocontrol Multi-volt, fail-on, 8A at 120V and 5A at 277V HI-LL-127-15-BK-12 Specifications subject to change without notice. 10 Page 2 of 2 Rev: 10/4/2018

Mogul-Base LED Replacement Lamp 3000K, 4000K / 27W, 36W, 45W, 54W Specification Sheet Project: Catalog#: Approved by: LEDMXR No Ballast needed (UL Type B) Internal driver/line voltage lamp Remove ballast from fixture Features Reduced Uplight, Base Down Cutoff Distribution, No LED s on Top 107-109 Lm/W Power Factor: >0.9 CCT: 3000K or 4000K; CRI: >80 Long Life: 10 years Operating temperature range: -40 to +140 F IP64 Design - Driver is fully potted with silicone. Waterproof, dust proof, and bug proof Flame retardant material UL/cUL Listed, UL Classified 120-277 VAC, 50/60Hz Non-dimming Warranty: 5 Years No Fan Ordering Information Applications Acorn Post Top Ball Catalog # Lumens CCT Watts Lm/W Cover Base Replacement LEDMXR-3027-MV 2900 3000 27 107 Clear EX39 100W HPS or MH LEDMXR-4027-MV 2900 4000 27 107 Clear EX39 100W HPS or MH LEDMXR-3036-MV 3900 3000 36 108 Clear EX39 150W HPS or MH LEDMXR-4036-MV 3900 4000 36 108 Clear EX39 150W HPS or MH LEDMXR-3045-MV 4900 3000 45 109 Clear EX39 175W MH LEDMXR-4045-MV 4900 4000 45 109 Clear EX39 175W MH LEDMXR-3054-MV 5900 3000 54 109 Clear EX39 200W HPS or MH LEDMXR-4054-MV 5900 4000 54 109 Clear EX39 200W HPS or MH Specifications subject to change without notice. Page 1 of 2 Rev: 10/4/2018 11

Specification Sheet Mogul-Base LED Replacement Lamp 3000K, 4000K / 27W, 36W, 45W, 54W Project: Catalog#: Approved by: LEDMXR Dimensions (in) 3.43 3.43 3.43 3.43 8.2 8.5 9.6 10.6 27W 36W 45W 54W LEDMXR vs. Common Lamp Sizes Lamp Base L (in.) D (in.) LEDMXR-XX27-MV 8.2 LEDMXR-XX36-MV 8.5 EX39 LEDMXR-XX45-MV 9.6 3.43 LEDMXR-XX59-MV 10.6 LU100 LU150/55 7.75 2.94 MH150/U E39 8.31 MH175/U H39KB-175 8.25 H37KC-175/DX 3.5 Specifications subject to change without notice. Page 2 of 2 Rev: 10/4/2018 12

Specification Sheet Medium-Base LED Replacement Lamp 3000K, 4000K / 15W, 19W, 24W / 130 Lm/W Project: Catalog#: Approved by: LEDMEDR No Ballast needed (UL Type B) Internal driver/line voltage lamp Remove ballast from fixture Features 130 Lm/W 360 Beam Angle (Omni Directional) Power Factor: >0.9 CCT: 3000K or 4000K; CRI: >80 Long Life: 10 years Operating temperature range: -40 to +60 C IP64 Design - Driver is fully potted with silicone. Waterproof, dust proof, and bug proof Flame retardant material UL/cUL Listed, UL Classified 120-277 VAC, 50/60Hz Built-in 4kV surge protection Non-dimming Warranty: 5 Years Applications Wallpack Posttop Includes Mogul Base to Medium Base Socket Reducer (E39 - E26) Acorn Ball Pendant Floodlight Posttop Garage Light Ordering Information Catalog # Lumens CCT Watts Lm/W Cover Base Replacement LEDMEDR-3015-MV 1950 3000 15 130 Clear E26 MED 50W HPS or MH LEDMEDR-4015-MV 1950 4000 15 130 Clear E26 MED 50W HPS or MH LEDMEDR-3019-MV 2470 3000 19 130 Clear E26 MED 70W HPS or MH LEDMEDR-4019-MV 2470 4000 19 130 Clear E26 MED 70W HPS or MH LEDMEDR-3024-MV 3120 3000 24 130 Clear E26 MED 100W HPS or MH LEDMEDR-4024-MV 3120 4000 24 130 Clear E26 MED 100W HPS or MH Specifications subject to change without notice. Page 1 of 2 Rev: 10/4/2018 13

Specification Sheet Medium-Base LED Replacement Lamp 3000K, 4000K / 15W, 19W, 24W / 130 Lm/W Project: Catalog#: Approved by: LEDMEDR Dimensions (in) 2.52 2.52 2.52 5.67 6.1 6.65 15W 19W 24W LEDMEDR vs. Common Lamp Sizes Lamp Base L (in.) D (in.) LEDMEDR-XX15-MV 5.67 LEDMEDR-XX19-MV E26 (default) 6.1 LEDMEDR-XX24-MV 6.65 2.52 LEDMEDR-XX15-MV 6.57 LEDMEDR-XX19-MV w/ adapter (Adds 0.9 inch) 7.0 LEDMEDR-XX24-MV 7.55 LU100 LU150/55 7.75 2.94 MH150/U E39 8.31 MH175/U H39KB-175 8.25 H37KC-175/DX 3.5 Specifications subject to change without notice. Page 2 of 2 Rev: 10/4/2018 14

F32T8/8XX/LED/16W/AC Linear LED Lamps 10/04/2016 Linear LED T8 Lamp F32T8 / 4Ft / 16W Internal Driver/Line Voltage LED Linear T8 Replacement Lamps are the ideal energy saving product when upgrading traditional T8 or T12 fluoescent lamps in fixtures. The LED T8 lamps are designed to provide a dedicated internal driver and utilizes nonshunted G13 medium bipin lamp holders. Features: F32T8 / 4 Foot LED Energy Saving Lamps 16W / 2,200 Lumens / 130 lm/w 82 CRI Power Factor ( PF ) > 0.9 Total Harmonic Distortion (THD) 20% Internal driver/line voltage (UL Type B) No ballast needed Must use non-shunted lamp holders Designed to operate between -20 C and 45 C ambient temperature Environmentally friendly: no mercury, no UV or infrared light Low lumen depreciation -- 50,000 hour rated life Minimum heat emission, reducing load on building cooling systems. Instant-on, no delay or flicker Used for upgrading T8 and T12 fixtures Uses G13 medium bipin lampholders Glass tube for superior optical performance Opal lens prevents glare 5-Year Warranty Colors Available 3000* 3500 4000 4500* 5000 Catalog # Length (in) Power (W) F32T8/830/LED/16W/AC* 48 16 Driver CCT Initial Lumens CRI Beam Angle Life 3000K 2200 82 240 50,000 F32T8/835/LED/16W/AC F32T8/840/LED/16W/AC F32T8/845/LED/16W/AC* 48 48 48 16 16 16 Internal Driver allows for bypassing of existing ballast 3500K 4000K 4500K 2200 2200 2200 82 82 82 240 240 240 50,000 50,000 50,000 F32T8/850/LED/16W/AC 48 16 5000K 2200 82 240 50,000 * Non-stock item Dimensions C D Dimension Min Max A B A N/A 47.22 in. (1199.4 mm) B 47.40 in. (1204 mm) 47.50 in. (1206.5 mm) C 47.67 in. (1210.8 mm) 47.78 in. (1213.6 mm) D 0.98 in. (25 mm) 1.02 in. (26 mm) No Ballast needed (UL Type B) Internal driver/line voltage lamp Must use non-shunted lamp holders 5 Year Warranty Visit www.designlights.org for the Qualified Products List Specifications subject to change without notice. 15

F32T8/8XX/LED/14W 4/3/2017 Linear LED T8 Lamp Direct Replacement LED T8: snap in, turn on! Linear LED Lamps Howard s Direct Replacement LED T8 lamp does not require an electrical re-wiring to install. Because the LED T8 s work with instant start ballasts and some programmed start ballasts, they are independent of the ballast operating voltage. This makes switching to LEDs as simple as changing a light bulb (no rewiring or special handling required). Features: No rewiring needed Direct replacement works with existing fluorescent T8 lamp fixtures (instant start and programmed start electronic ballasts) Low energy usage Environmentally friendly: no mercury, no UV or infrared light Low lumen depreciation -- maintains brightness over its 50,000 hour rated life Minimum heat emission, reducing load on building cooling systems. Instant-on, no delay Quick and easy installation Can utiliize existing instant start or rapid start sockets Works with dimming ballast Compatible with controls and sensors Works in cold temperature and applications Glass tube for superior optical performance No flickering Long-life High CRI 85 5-Year Warranty Auto-adjusts to the corresponding Ballast Factor 13w (Low Ballast Factor) 14w (Standard Ballast Factor) 20w (High Ballast Factor) Colors Available 3000* 3500 4000 4500* 5000 UPC Code Catalog # Length (in) Power (W) 62013 F32T8/830/LED/14W* 48 14 Driver CCT Initial Lumens** CRI Beam Angle Lamp Efficacy System Efficacy 3000K 1800 85 325 130 115 50,000 Life 62010 62011 62014 F32T8/835/LED/14W F32T8/840/LED/14W F32T8/845/LED/14W* 48 48 48 14 14 14 Instant Start or Program Start Electronic T8 Ballast 3500K 4000K 4500K 1800 1800 1800 85 85 85 325 325 325 130 130 130 115 115 115 50,000 50,000 50,000 62012 F32T8/850/LED/14W 48 14 5000K 1800 85 325 130 115 50,000 *Non-stock item **Performance is ballast dependent 5 Year Warranty Visit www.designlights.org for the Qualified Products List Specifications subject to change without notice. 16

F17T8/8XX/LED/11W 4/3/2017 Linear LED T8 Lamp F17T8 / 2Ft / 11W Linear LED Lamps Direct Replacement LED T8 lamp does not require an electrical re-wiring to install. Because the LED T8 s work with instant start ballasts and some programmed start ballasts, they are independent of the ballast operating voltage. This makes switching to LEDs as simple as changing a light bulb (no rewiring or special handling required). Features: F17T8 / 2 Foot LED Energy Saving Lamps 11W / 1,100 Lumens / 104 lm/w 82 CRI Replacement lamp ( Plug and Play ) (UL Type A) Works with existing fluorescent T8 lamp fixtures (instant start and programmed start electronic ballasts) Designed to operate between -20 C and 45 C ambient temperature Environmentally friendly: no mercury, no UV or infrared light Low lumen depreciation -- 50,000 hour rated life Minimum heat emission, reducing load on building cooling systems. Instant-on, no delay or flicker Glass tube for superior optical performance Opal lens prevents glare Works with G13 medium bipin lampholders 5-Year Warranty Catalog # Length (in) Power (W) F17T8/830/LED/11W* 24 11 Driver CCT Initial Lumens CRI Colors Available 3000* 3500 4000 4500* 5000 Beam Angle Life 3000K 1100 82 240 50,000 F17T8/835/LED/11W F17T8/840/LED/11W F17T8/845/LED/11W* 24 24 24 11 11 11 Instant Start or Program Start Electronic T8 Ballast 3500K 4000K 4500K 1100 1100 1100 82 82 82 240 240 240 50,000 50,000 50,000 F17T8/850/LED/11W 24 11 5000K 1100 82 240 50,000 * Non-stock item Dimensions C D Dimension Min Max A B A N/A 23.22 in. (589.8 mm) B 23.40 in. (594.4 mm) 23.50 in. (596.9 mm) C 23.67 in. (601.2 mm) 23.78 in. (604 mm) D 0.98 in. (25 mm) 1.02 in. (26 mm) Plug and play replacement lamp (UL Type A); Ballast is necessary 5 Year Warranty Visit www.designlights.org for the Qualified Products List Specifications subject to change without notice. 17

Direct Replacement T8 LED Lamps 9/5/2018 Linear LED T8 Lamp Direct Replacement LED T8: snap in, turn on! Howard s Direct Replacement LED T8 lamp does not require an electrical re-wiring to install. Because the LED T8 s work with instant start ballasts and some programmed start ballasts, they are independent of the ballast operating voltage. This makes switching to LEDs as simple as changing a light bulb (no rewiring or special handling required). Features: Performance Characteristics: Quick and easy installation. No rewiring needed Direct replacement works with most existing fluorescent T8 lamp ballasts (instant start and programmed start electronic ballasts) Compatible with emergency ballast Low energy usage Environmentally friendly: no mercury, no UV or infrared light Low lumen depreciation maintains brightness over its 50,000 hour rated life Minimum heat emission, reducing load on building cooling systems. Instant-on, no delay Can utilize existing instant start or rapid start sockets Compatible with controls and sensors Works in cold temperature and applications Glass tube for superior optical performance No flickering Long-life Complies with FCC 47 Part 15 Class B, ballast dependent Complies with UL1993/UL8750 5-Year Warranty Length: 48 in. Ignition Time: 1.0 s High CRI >80 Beam Angle: 325 Operation temperature: -20 C (-4 F) to 45 C (113 F) Storage temperature: -40 C (-40 F) to 85 C (185 F) Target replacement lamps F25T8 (4ft), F28T8 (4ft), F30T8 (4ft), F32T8 (4ft) Plug and play replacement lamp (UL Type A); Ballast is necessary Model Code Power* (W) Initial Lumens* CCT CRI Life Cap DLC T8L-1800-4ft-CBA-91 1 11.5 1800 4000 82 50,000 Plastic T8L-1800-4ft-EBA-A1 2 12 1800 5000 82 50,000 Aluminum T8L-2200-4ft-CBA-91 3 15 2200 4000 82 50,000 Plastic T8L-2200-4ft-EBA-91 4 15 2200 5000 82 50,000 Plastic T8L-2200-4ft-EBA-A1 5 15 2200 5000 82 50,000 Aluminum * Performance is ballast dependent. Value shown above is based on standard ballast factor. 1. Full model number and DLC listed as: T8L-IDDM13-1800-4ft-CBA-91 2. Full model number and DLC listed as: T8L-IDDM13-1800-4ft-EBA-A1 3. Full model number and DLC listed as: T8L-IDDM13-2200-4ft-CBA-91 4. Full model number and DLC listed as: T8L-IDDM13-2200-4ft-EBA-91 5. Full model number and DLC listed as: T8L-IDDM13-2200-4ft-EBA-A1 18

F32T8/8XXLED/12.5W/AC 08/29/18 Linear LED T8 Lamp Internal Driver/Line Voltage LED T8 Internal Driver/Line Voltage LED Linear T8 Replacement Lamps are the ideal energy saving product when upgrading traditional T8 or T12 fluorescent lamps in fixtures. The LED T8 lamps are designed to provide a dedicated internal driver and utilizes non-shunted G13 medium bi-pin lamp holders. Features: Performance Characteristics: F32T8 / 4 Foot LED Energy Saving Lamps Internal driver/line voltage (UL Type B) No ballast needed Uses G13 medium bi-pin lamp holders Must use non-shunted lamp holders Low energy usage Environmentally friendly: no mercury, no UV or infrared light Low lumen depreciation maintains brightness over its 50,000 hour rated life Minimum heat emission, reducing load on building cooling systems. Instant-on, no delay or flicker Used for upgrading T8 and T12 fixtures Compatible with controls and sensors Works in cold temperature and applications Glass tube for superior optical performance Opal lens prevents glare Used for upgrading T8 and T12 fixtures No flickering Length: 48 in. Input Voltage: 120 277Vac Power Factor: 0.90 (-3% tolerance) Total Harmonic Distortion : 20% (+5% tolerance) High CRI >80 Beam Angle: 240 Operation temperature: -20 C (-4 F) to 45 C (113 F) Storage temperature: -40 C (-40 F) to 85 C (185 F) Target replacement lamps F25T8 (4ft), F28T8 (4ft), F30T8 (4ft), F32T8 (4ft) No Ballast needed (UL Type B) Internal driver/line voltage lamp Must use non-shunted lamp holders Model # Power (W) Initial Lumens CCT CRI Life F32T8/840LED/12.5W/AC 1 12.5 1800 4000 82 50,000 F32T8/850LED/12.5W/AC 2 12.5 1800 5000 82 50,000 1. DLC listed as T8L-IDFH13-1800-4ft-CBA-50 2. DLC listed as T8L-IDFH13-1800-4ft-EBA-11 Dimensions: Dimension Min Max A N/A 47.22 in. (1199.4 mm) B 47.40 in. (1204 mm) 47.50 in. (1206.5 mm) B 47.67 in. (1210.8 mm) 47.78 in. (1213.6 mm) D 0.98 in. (25 mm) 1.02 in. (26 mm) 19

4/10/2016 U-Shaped LED T8 Lamp FB32T8 / 6in Spacing / 12W FB32T8/8XX/LED/12W U-Shaped LED Lamps Direct Replacement LED T8 lamp does not require an electrical re-wiring to install. Because the LED T8 s work with instant start ballasts and some programmed start ballasts, they are independent of the ballast operating voltage. This makes switching to LEDs as simple as changing a light bulb (no rewiring or special handling required). Features: FB32T8 / 6 Inch Spacing LED Energy Saving Lamps 12W / 1,700 Lumens / 135 lm/w (3000K, 3500K) 12W / 1,800 Lumens / 145 lm/w (4000K, 4500K, 5000K) 82 CRI Replacement lamp ( Plug and Play ) (UL Type A) Works with existing fluorescent T8 lamp fixtures (instant start and programmed start electronic ballasts) Designed to operate between -20 C and 45 C ambient temperature Environmentally friendly: no mercury, no UV or infrared light Low lumen depreciation -- 50,000 hour rated life Minimum heat emission, reducing load on building cooling systems. Instant-on, no delay or flicker Glass tube for superior optical performance and frosted glass prevents glare Works with 2G13 medium bipin lampholders 5-Year Warranty Colors Available 3000* 3500 4000 4500* 5000 Catalog # Length (in) Power (W) FB32T8/830/LED/12W 6in spacing 12 Driver CCT Initial Lumens CRI Life 3000K 1700 82 50,000 FB32T8/835/LED/12W FB32T8/840/LED/12W FB32T8/845/LED/12W 6in spacing 6in spacing 6in spacing 12 12 12 Instant Start or Program Start Electronic T8 Ballast 3500K 4000K 4500K 1700 1800 1800 82 82 82 50,000 50,000 50,000 FB32T8/850/LED/12W 6in spacing 12 5000K 1800 82 50,000 * Non-stock item Dimensions B A E Leg strap Dimension A B C D E D Max 5.98 in. (152 mm) 22.44 in. (570 mm) 1.02 in. (26 mm) 0.98 in. (24.8 mm) 1.09 in. (27.8 mm) 5 Year Warranty C Plug and play replacement lamp (UL Type A); Ballast is necessary Specifications subject to change without notice. 20

LONG LIFE SERIES PHOTOCONTROL OVERVIEW Howard Lighting Products photocontrols were designed for the demands of HID and solid-state lighting (SSL), making them an excellent choice for LED, conventional & Electronic HID, and Induction luminaires. Controls APPLICATIONS LED luminaires that require dusk to dawn control. Recommended for luminaires that use solid state ballasts/drivers (e.g. CFL, Induction, Electronic HID, LED). FEATURES The HI-LL is specifically designed to provide long-life, enhanced light sensitivity, and superior surge protection when used with LED luminaires. Filtered Silicon Light Sensor - sensitive to Sunlight but not LED. Sealed relay. MOV Surge Suppressor rated for 640 Joules/20,000 Amp. Base Gasket has a continuous use temperature of 105 C. 3 6 second turn-off delay. Black cover standard. Other colors optional. SPECIFICATIONS REGULATORY LISTINGS Meets ANSI C136.10 ROHS compliant Manufactured in a ISO certified facility Surge Rated to (and exceeds) ANSI C136.10 Extreme surge level OPERATING CHARACTERISTICS Voltage 105 to 305 VAC, 60Hz Load rating: 1800VA driver or ballast load. Up to 200 amp inrush Temp. -40 to +70 C ambient ADDITIONAL FEATURES ENHANCED LIGHT SENSING The silicon photo sensor is designed to sense sunlight, while being blind to light emitted from LEDs. This reduces LED sensitivity and greatly decreases false turn-off in high ambient light situations. INRUSH PROTECTION Tested and approved for use with fixtures that use multiple LED drivers, the HI-LL can withstand the high inrush current that these drivers generate. SURGE PROTECTION Employing four MOV s exceeds ANSI Extreme Category (20kV, 10kA) surge protection for the control, and also protects the solid state driver from differential mode transients. DESIGN LIFE ENHANCEMENTS Design life is period of time that the product is expected to work within its specified parameters; the HI-LL is rated for 90,000 hours. Printed circuit board is fiber-glass/epoxy FR4 for superior strength and moisture resistance, and is conformally coated on both sides to reduce water absorption.the cover is 0.105 inches thick for better impact resistance, compared to 0.06 inches on standard controls. Cover is sealed to the base to provide IP64 ingress protection. LONG LIFE CONTROL HI-LL VOLTAGE TURN ON LEVELS (1.5 ratio) COVER COLOR WARRANTY TERM FAILURE MODE 127: 120-277 VAC 15: 1.5fc (ANSI Standard) BK: Black 12: 12 year Blank: Fail ON 480: 347-480 VAC 10: 1.0fc BU: Blue F: Fail OFF 26: 2.6fc (IES) GN: Green WARRANTY All photocontrols are marked with date of manufacture. This product is warrantied to operate within its original specifications and shall be free of electrical or mechanical defects. Consult factory for the warranty time period. Manufacturer s warranty shall be limited to providing a replacement control of same type and shall not cover costs of removal, replacement or loss of service nor any consequential damages. This warranty is in lieu of and excludes all other warranties either expressed or implied. Full warranty statement is available by consulting factory. 01-30 17 Specifications subject to change without notice. 21

Notes 22

Notes 23

580 Eastview Drive Laurel, MS 39443 P.O. Box 1590 Laurel, MS 39441 800.956.3456 general 601.422.0033 601.422.1652 fax www.howard-lighting.com Revision Revision Date: Date: 10/3/2017 1/25/2019 24