PRIMERGY BX924 S2 System configurator and order-information guide September 2012 Contents Instructions Configuration diagram Configurator # X BX924 S2 Dual Socket 20 # XI Processor 21 # XII Storage # XIII Memory # XIV irmc S2, Graphics # XV Mezzanine Cards # PRIMERGY Server
Instructions This document contains basic product and configuration information that will enable you to configure your system via System-Architect. Only the tool "System-Arcitect" will ensure a fast and proper configuration of your PRIMERGY server or your complete PRIMERGY Rack system. Please pay attention to the naming conventions: BX924 S2 Dual Server Blade S2 You can configure your individual PRIMERGY server in order to adjust your specific requirements. The System configurator is divided into several chapters that are identical to the current price list and PC-/ System-Architect. Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through the configurator by following the lines from the top to the bottom. Section IV Memory, example There are 3 free memory banks available. The memory banks can be populated with 512MB, 1GB, 2GB and 4GB DDR Memory. The maximum total amount of memory is 12GB. It is possible to select memory upgrade options up to 3 times. ECC with memory scrubbing-function and hot-spare memorybank is standard on the PRIMERGY BX600 S2 Server Blades. X times S26361-XXX-XXX Memory XXX MB S26361-XXX-XXX Memory XXX MB max. X times per system max. X times per system In one chapter you can only select as many components (here 3x) as the arrow indicates. 3x Please note that there are information symbols which indicate necessary information. For further information see: http://ts.fujitsu.com/products/standard_servers/index.html (internet) https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/pages/currentconfigurators.aspx (extranet) Prices and availability see price list and PC-/ System-Architect Subject to change and errors excepted Fujitsu Technology Solutions x86 PRIMERGY Server 2 of 14
Configuration diagram Dual Server Blade BX924 S2 Mezzanine slot 1 disk mounting kit Row 1 (3 DIMMS) FC Mezz. card 2.5" SSD CPU1 1/10 GbE Mezz. card Row 2 (3 DIMMS) IB Mezz. card 2.5" SSD Intel CPU or Row 3 (3 DIMMS) unpopulated Mezzanine slot 2 FC Mezz. card disk mounting kit Row 1 (3 DIMMS) 1/10 GbE Mezz. card CPU2 IB Mezz. card Row 2 (3 DIMMS) or Disks Intel CPU unpopulated Row 3 (3 DIMMS) UFM Processor Memory Mezzanine slot UFM Key: Included in basic unit Option The population order for the CPU is: CPU1 first, then CPU2 The population order for the DIMMs: for each CPU, the DIMM row 1 (DIMMS 1A 1B 1C) (DIMMS 1D 1E 1F) first, then row 2 (DIMMs 2A, 2B, 2C) (DIMMs 2D, 2E, 2F) Fujitsu Technology Solutions x86 PRIMERGY Server 3 of 14
UDIMM LV / 1.35V 1333Mhz UDIMM 1.5V 1333Mhz RDIMM LV / 1.35V 1333Mhz RDIMM 1.5V 1333Mhz System configurator and order-information guide Memory Configuration PRIMERGY BX924 S2 Each CPU offers 9 Slots for DDR3 Memory Modules organised in 3 Banks and 3 Channels. Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below). There are 4 different kinds of DDR3 Memory Modules available: UDIMM / UDIMM LV and RDIMM / RDIMM LV UDIMM and RDIMM offer different functionality. Mix of UDIMM + RDIMM is not alloved. Mixing of Standard + Low Voltage DIMM s of the same type is allowed, but not recommendet (therefore not configurable ex works) If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V Mixing of SR / DR and QR Memory Modules will limit the max. amount of modules per CPU to 6. Mode Configuration UDIMM RDIMM Application chip kill support any n.a. yes detect multi-bit errors Independant Channel 1, 2 or 3 Modules per Bank x x offers max. flexibility, upgradeability, capacity Mode use UDIMM modules for lowest cost Mirrored Channel Mode 2 identical Modules / Bank **) x offers maximum security Performance Mode *) 3 identical Modules / Bank **) x offers maximum performance and capacity Spare Channel Mode *) 3 identical Modules / Bank **) x balances security and capacity *) = Performance Mode and Spare mode use different BIOS settings. **) = technically possible but no Order Numbers available, use at your own risk x = order codes available Capacity Configuration UDIMM RDIMM RDIMM LV Notes Min. Memory per CPU 1 Module / CPU 1x2GB 1x2GB 1x 4GB with one CPU Max. Memory per CPU 6/9 Modules / CPU 6x2GB 6x16GB 6x 8GB with one CPU Max. Memory per System 12 Modules / System 24GB 192GB 96GB if second CPU is configured Memory-Speed: Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU One DIMM per channel = max. 1333MHz, two DIMMs per channel = max. 1333MHz for 1.5V / max. 1066 for 1.35V memory, three DIMMs per channel = max. 800MHz. The memory channel with the lowest speed defines the speed of all CPU channels in the system DIMM Type DIMM Slots DIMMs populated Memory Speed Ranks per DIMM per Channel per Channel max (CPU dependent) 2 / 3 1 2 / 3 1 2 / 3 2 2 / 3 2 3 3 800 2 / 3 1 2 / 3 1 2 / 3 2 2 / 3 2 2 / 3 1 800, 1066, 1333 SR / DR 800, 1066 QR 800, 1066, 1333 800 Mix of SR + DR Mix of QR + SR / DR Mix of SR + DR 800, 1066, 1333 SR / DR 800, 1066 QR* 800, 1066 800 Mix of SR + DR Mix of QR* + SR / DR 800, 1066, 1333 SR / DR 2 / 3 2 800, 1066, 1333 Mix of SR + DR 2 / 3 1 800, 1066, 1333 SR / DR 2 / 3 2 800, 1066 Mix of SR + DR * no memory modules released for this configuration ** lost LV-mode, memory will switch to 1,5V Vcc automatically Fujitsu Technology Solutions x86 PRIMERGY Server 4 of 14
UDIMM 1333 MHz 1.5V UDIMM 1333 MHz LV / 1.35V RDIMM 1333 MHz 1.5V RDIMM 1333 MHz LV / 1.35V RDIMM 1066 MHz (QR) 1.5V System configurator and order-information guide Used CPU Max. Memory-Bus speed depending on DIMMs / channel if following memory speed is used for specific CPU`s Populated Dimms / Channel 1 2 3 1 2 Dual-Core CPU with max. 800MHz DDR3 speed (4.8GT/s) Xeon E5503 2C/2.00GHz/2M/4,80GT/s (80W) Quad-Core CPU`s with max. 800MHz DDR3 speed (4.8GT/s) Xeon E5506 4C/2.13GHz/4M/4,8GT/s (80W) Xeon E5507 4C/2.26GHz/4M/4,8GT/s (80W) Turbo Quad-Core CPU`s with max. 1066MHz DDR3 speed (5.86GT/s) Xeon E5620 4C/2.40GHz/12M/5,86GT/s (80W) Xeon E5630 4C/2.53GHz/12M/5,86GT/s (80W) Xeon E5640 4C/2.66GHz/12M/5,86GT/s (80W) Turbo Six-Core CPU`s with max. 1333MHz DDR3 speed (6.4GT/s) Xeon X5650 6C/2.66GHz/12M/6,40GT/s (95W) Xeon X5660 6C/2.80GHz/12M/6,40GT/s (95W) Xeon X5670 6C/2.93GHz/12M/6,40GT/s (95W) Xeon X5680 6C/3.33GHz/12M/6,40GT/s (130W) Frequency Optimized Turbo Quad-Core CPU`s with max. 1333MHz DDR3 speed (6.4GT/s) Xeon X5667 4C/3.06GHz/12M/6,40GT/s (95W) Xeon X5677 4C/3.46GHz/12M/6,40GT/s (130W) Low Voltage Quad-Core CPU with max. 800MHz DDR3 speed (4.8GT/s) Xeon L5609 4C/1.60GHz/12M/4.80GT/s (40W) Low Voltage Turbo Quad-Core CPU with max. 1066MHz DDR3 speed (5.86GT/s) Xeon L5630 4C/2.13GHz/12M/5,86GT/s (40W) Xeon L5640 6C/2.40GHz/12M/5.86GT/s (60W) SR - Single Rank - 1Rx4 DR - Dual Rank - 2Rx4 QR - Quad Rank - 4Rx4 1DPC = 1 DIMM per Channel 2DPC = 2 DIMM per Channel 3DPC = 3 DIMM per Channel 1333 1066 800 not supported special release Configuration hints: 800 800-800 800-800 800-800 800 - - The memory sockets on the systemboard offer a color coding: Bank I black sockets Bank II blue sockets Bank III green sockets 800 800-800 800-800 800 800-800 800-800 800 1066 1066-1066 1066-1066 1066-1066 1066-1066 1333 1333-1333 1066-1333 1333 1333 1333-1333 1066-1333 1333 800 1333 1333-1333 1066-1333 1333-1333 1066-1333 3 1 2 3 1 2 1066 1066-1066 1066-1066 1066 800 1333 1333-1333 1066-1333 1333 800 1333 1066-1066 800-1333 1333-1333 1066-1333 1333 800 1333 1066-1066 800-1066 1066-1066 1066-1066 1066 800 1066 1066-1066 800-1066 1066-1066 1066-1066 1066 800 1066 1066-1066 800 - - A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below) Bank I on CPU 1 up to 3 memory modules connected to Channel A, B and C on the first CPU Bank II on CPU 1 up to 3 memory modules connected to Channel A, B and C on the first CPU Bank III on CPU 1 up to 3 memory modules connected to Channel A, B and C on the first CPU Bank I on CPU 2 up to 3 memory modules connected to Channel D, E and F on the second CPU Bank II on CPU 2 up to 3 memory modules connected to Channel D, E and F on the second CPU Bank III on CPU 2 up to 3 memory modules connected to Channel D, E and F on the second CPU - See below and next page for a detailed descriptions of the memory configuration supported. 800 800 800 800 800-800 800 800 800-800 800 800 800-800 800 1066 1066 800 1066 1066-1066 800 1066 1066-1066 800 1333 1066-1066 800 1333 1333 800 1333 1066-1333 800 1333 1066-1066 800 800 800 800 800-3 1 2 3 800 800-800 - 1066 1066-1066 800-1066 800-800 - 1333 1066-1066 800-1066 800-800 - 800 800 - - - Fujitsu Technology Solutions x86 PRIMERGY Server 5 of 14
Channel A Channel B Channel C Channel D Channel E Channel F Channel A Channel B Channel C Channel D Channel E Channel F Channel A Channel B Channel C Channel D Channel E Channel F Channel A Channel B Channel C Channel D Channel E Channel F 1. Independent Channel Mode System configurator and order-information guide required required if 2nd CPU is configured Bank I Data Data Data Data Data Data optional, same type in Bank per CPU (black sockets) Bank II Data Data Data Data Data Data optional, any type (blue sockets) Bank III Data Data Data Data Data Data -------- not used (green sockets) 1st XEON CPU (Dual-or Quad Core) Independent Channel Mode allows all channels to be populated in any order Can run with differently rated DIMMs and use the settings of the slowest DIMM within a channel 2. Mirrored Channel Mode 2nd XEON CPU (Dual-or Quad Core) required required if 2nd CPU is configured Bank I Data Mirror -------- Data Mirror -------- optional, same type in Bank per CPU (black sockets) Bank II Data Mirror -------- Data Mirror -------- -------- not used (blue sockets) Bank III Data Mirror -------- Data Mirror -------- (green sockets) 1st XEON CPU (Dual-or Quad Core) Mirrored Channel Mode requires identical modules on channel A and B (1st CPU) or channel D and E (2nd CPU) 50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory Channel C (1st CPU) or channel F (2nd CPU) are not usable in Mirrored Channel Mode 3. Performance Channel Mode 2nd XEON CPU (Dual-or Quad Core) required required if 2nd CPU is configured Bank I Data Data Data Data Data Data optional, same type in Bank per CPU (black sockets) Bank II Data Data Data Data Data Data optional, any type (blue sockets) Bank III Data Data Data Data Data Data -------- not used (green sockets) 1st XEON CPU 2nd XEON CPU Performance Channel Mode requires identical modules on all channels of each Bank per CPU 4. Spare Channel Mode (only available with 56xx CPUs) required required if 2nd CPU is configured Bank I Data Data Spare Data Data Spare optional, same type in Bank per CPU (black sockets) Bank II Data Data Spare Data Data Spare optional, any type (blue sockets) Bank III Data Data Spare Data Data Spare -------- not used (green sockets) 1st XEON CPU 2nd XEON CPU Spare Channel Mode requires identical modules on all channels of each Bank per CPU one third of the capacity is used for the spare => the available memory for applications is two thirds of the installed memroy Spare Channel Mode is supported using RDIMM memory modules Fujitsu Technology Solutions x86 PRIMERGY Server 6 of 14
D Section X Dual Socket Server Blade BX924 S2 Server Blade with: - Dual INTEL Nehalem/Westmere Processor Support as Dual-Core / Quad-Core / Six-Core - The base units with INTEL Processor - 18 DIMM sockets, organized in 3 DPC for each CPU (9 DIMMs per CPU) - 1x Intel Niantic dual channel 10 Gbit Ethernet LAN controller on-board (=2x 1/10Gbit/s) - 2 bays for optional 2.5" SATA SSD disks (non hot-plug) - irmc S2 on-board - Special connector for Y-cable (4x USB, 1 x serial 1x VGA). The BX924 S2 Server Blade can be installed max. 18x in the BX900 S1 System Unit S26361-K1341-V200 S26361-F4478-L1 PY BX924 S2 Dual Server Blade PY BX900 Y-Cable frontside up to 2x 2.5" SSD drives. for KVM connection to Dual Server Blade Base Unit without Server Blade 18x CPU and without memory modules! 4x USB, 1x VGA, 1x seriell PY BX924 S2 Dual Server Blade For CPU and Memory configuration see below Max. 18x per BX900 System Unit. S26361-F3552-E1 TPM Module Trusted Platform Module on motherboard PY TPM Module Be aware of import restrictions! Max. 1x per Server Blade. If installation is done locally, make sure you have USB stick available for driver installation. Following USB Components are available 1) USB DVD SM / Blu-Ray as soon as available External SuperMulti Drive External Blu-Ray Drive S26341-F103-L126 S26341-F103-L127 2) USB Keyboard: KBPC PX ECO Green IT, professional keyboard S26381-K341-E1xx / L1xx 3) USB Mouse: S26381-K430-L100 Laser Moue USB/PS2 Combo 4) USB Sticks: MyUSBS A910 8GB, MLC Flash MyUSBS A910 16GB, MLC Flash S26391-F6048-L208 S26391-F6048-L216 S26361-F2749-E1 S26361-F2749-E2 Service for Server Blade installation in the System Unit. Server Blade individually packed / delivered. Hereby the BX900 S1 will be delivered completely The Server Blade is not built in a BX900 S1, configured and tested with Server Blades integrated. it is separately tested and delivered. This order number must be in the same order as the System Unit itself. Contains ServerStart CD min. 1x per System Unit; max. 18x per System Unit; max. 1x per Server Blade max. 1x per Server Blade E Fujitsu Technology Solutions x86 PRIMERGY Server 7 of 14
E System configurator and order-information guide Section XI Processor There are 2 processor sockets available. Both sockets must equipped with CPUs A multi-processor operating system is required for a dual-processor system. Note: Max. DDR3 Bus Speed depends on: - max. DDR3 Bus Speed from the CPU and - max. DDR3 Memory Speed and - max. memory modules on one memory channel The optional SSDs are mounted on top of the CPUs Thus it is importanted to choose CPUs types Choose SSD capable CPU types only if you order SSDs Caution - the SSD option may reduce the thermal performance of the Blade without SSD For configurations w/o SSD holder choose these CPUs With this order number you will receive two CPUs without SSD support The BX924 is always delivered with two CPUs installed. Please choose the CPU type (applies to both CPUs) Dual-Core CPU with max. DDR3 Bus Speed 800MHz - 64-bit Intel Xeon DP (4MB shared TLC = Second Level Cache ) Xeon E5503 2C/2.00GHz/2M/4,80GT/s (80W) Quad-Core CPU`s with max. DDR3 Bus Speed 800MHz - 1x 64-bit Intel Xeon DP (4MB shared TLC = Second Level Cache ) Xeon E5506 4C/2.13GHz/4M/4,8GT/s (80W) Xeon E5507 4C/2.26GHz/4M/4,8GT/s (80W) Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz - 1x 64-bit Intel Xeon DP (4/8MB shared TLC = Second Level Cache ) S26361-F4444-E200 S26361-F4449-E213 S26361-F4444-E226 --> with SSD occupies socket for one CPU Xeon E5603 4C/1.60GHz/4M/4,80GT/s (80W) S26361-F4514-E160 Xeon E5606 4C/2.13GHz/8M/4,80GT/s (80W) S26361-F4514-E213 Xeon E5607 4C/2.26GHz/8M/4,80GT/s (80W) S26361-F4514-E226 on special release Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz 1x Xeon E5620 4C/2.40GHz/12M/5,86GT/s (80W) Xeon E5630 4C/2.53GHz/12M/5,86GT/s (80W) S26361-F4445-E240 S26361-F4445-E253 Xeon E5640 4C/2.66GHz/12M/5,86GT/s (80W) S26361-F4445-E266 Xeon X5647 4C/2.93GHz/12M/5,86GT/s (130W) S26361-F4517-E293 Turbo Quad-/Six-Core CPU`s with max. DDR3 Bus Speed 1333MHz Xeon E5645 6C/2.40GHz/12M/5,86GT/s (80W) S26361-F4515-E240 Xeon E5649 6C/2.53GHz/12M/5,86GT/s (80W) S26361-F4515-E253 Xeon X5650 6C/2.66GHz/12M/6,40GT/s (95W) S26361-F4446-E266 Xeon X5660 6C/2.80GHz/12M/6,40GT/s (95W) S26361-F4446-E280 Xeon X5670 6C/2.93GHz/12M/6,40GT/s (95W) S26361-F4446-E293 Xeon X5675 6C/3.06GHz/12M/6,40GT/s (95W) S26361-F4516-E306 Xeon X5680 6C/3.33GHz/12M/6,40GT/s (130W) S26361-F4477-E333 Xeon X5690 6C/3.46GHz/12M/6,40GT/s (130W) S26361-F4516-E346 Xeon X5667 4C/3.06GHz/12M/6,40GT/s (95W) S26361-F4446-E306 on special release Xeon X5677 4C/3.46GHz/12M/6,40GT/s (130W) S26361-F4476-E346 on special release Xeon X5687 4C/3.60GHz/12M/6,40GT/s (130W) S26361-F4517-E360 Low Voltage Quad-Core CPU with max. 800MHz DDR3 speed ( 4.8GT/s) with passive heat sink, Xeon L5609 4C/1.86GHz/12M/4.80GT/s (40W) S26361-F4447-E186 Low Voltage Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz Xeon L5630 4C/2.13GHz/12M/5,86GT/s (40W) Xeon L5640 6C/2.26GHz/12M/5.86GT/s (60W) S26361-F4447-E213 S26361-F4448-E226 F1 F2 Fujitsu Technology Solutions x86 PRIMERGY Server 8 of 14
F1 F2 For configurations with SSD holder choose these CPUs With this order number you will receive two CPUs with SSD support The BX924 is always delivered with two CPUs installed. Please chosse the CPU type (applies to both CPUs) Dual-Core CPU with max. DDR3 Bus Speed 800MHz - 64-bit Intel Xeon DP (4MB shared TLC = Second Level Cache ) Xeon E5503 2C/2.00GHz/2M/4,80GT/s (80W) Quad-Core CPU`s with max. DDR3 Bus Speed 800MHz - 64-bit Intel Xeon DP (4MB shared TLC = Second Level Cache ) occupies socket for one CPU Xeon E5506 4C/2.13GHz/4M/4,8GT/s (80W) Xeon E5507 4C/2.26GHz/4M/4,8GT/s (80W) Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz - 1x 64-bit Intel Xeon DP (4/8MB shared TLC = Second Level Cache ) S26361-F4456-E200 S26361-F4461-E213 S26361-F4456-E226 occupies socket for one CPU Xeon E5603 4C/1.60GHz/4M/4,80GT/s (80W) S26361-F4518-E160 Xeon E5606 4C/2.13GHz/8M/4,80GT/s (80W) S26361-F4518-E213 Xeon E5607 4C/2.26GHz/8M/4,80GT/s (80W) S26361-F4518-E226 on special release Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz 1x Xeon E5620 4C/2.40GHz/12M/5,86GT/s (80W) S26361-F4457-E240 Xeon E5630 4C/2.53GHz/12M/5,86GT/s (80W) S26361-F4457-E253 Xeon E5640 4C/2.66GHz/12M/5,86GT/s (80W) S26361-F4457-E266 Turbo Quad-/Six-Core CPU`s with max. DDR3 Bus Speed 1333MHz Xeon E5645 6C/2.40GHz/12M/5,86GT/s (80W) S26361-F4519-E240 Xeon E5649 6C/2.53GHz/12M/5,86GT/s (80W) S26361-F4519-E253 Xeon X5650 6C/2.66GHz/12M/6,40GT/s (95W) S26361-F4458-E266 Xeon X5660 6C/2.80GHz/12M/6,40GT/s (95W) S26361-F4458-E280 Xeon X5670 6C/2.93GHz/12M/6,40GT/s (95W) S26361-F4458-E293 Xeon X5675 6C/3.06GHz/12M/6,40GT/s (95W) S26361-F4520-E306 Xeon X5667 4C/3.06GHz/12M/6,40GT/s (95W) S26361-F4458-E306 on special release Xeon X5672 4C/3.20GHz/12M/6,40GT/s (95W) S26361-F4521-E320 Low Voltage Quad-Core CPU with max. 800MHz DDR3 speed ( 4.8GT/s) with passive heat sink, Xeon L5609 4C/1.86GHz/12M/4.80GT/s (40W) S26361-F4459-E186 Low Voltage Turbo Quad-Core CPU`s with max. DDR3 Bus Speed 1066MHz Xeon L5630 4C/2.13GHz/12M/5,86GT/s (40W) Xeon L5640 6C/2.40GHz/12M/5.86GT/s (60W) S26361-F4459-E213 S26361-F4460-E226 Section XII Storage Both hard disks are plugged in directly connected to the onboard controller. Two disks can be configured! One UFM can be installed independent from the disk drives Remark: UFM is part of the VMWare Embedded solution (S26361-F2341-E431) Remark: Currently VMWare RAID configurations are not supported 1x S26361-F4008-E2 BX924 Disk Drive mounting Kit supports up to 2 SSDs max. 1x per base unit SSD SATA 3Gb/s 2.5" non hot plug 64GB SLC S26361-F4008-E64 1-2x 100GB MLC, Mainstream Perfomance S26361-F5123-E100 MLC will not be released 200GB MLC, Mainstream Perfomance S26361-F5123-E200 400GB MLC, Mainstream Perfomance S26361-F5123-E400 F Fujitsu Technology Solutions x86 PRIMERGY Server 9 of 14
F Section XIII Memory For a description of memory configurations refer to section "Memory Configurations" Minimum one memory module or memory order code per CPU = first memory Registered (reg) RDIMMs (1.5V) Note 1.) For "Independent Channel Mode" usage! Max. DDR3 memory speed depends on the memory configuration - One DDR3 RDIMM ECC memory module of one CPU memory channel and on the speed of the CPU itself. 2GB (1333MHz/SR) S26361-F4412-E513 The memory channel with the lowest speed defines the speed 4GB (1333MHz/DR) S26361-F4412-E514 of all CPU channels in the system, also for the channels of the 8GB (1333MHz/DR) S26361-F4412-E515 second CPU if configured. 16GB (1066MHz/QR) S26361-F4412-E516 One DIMM per channel = max. 1333MHz for 1.5V + 1.35V memory 32GB (1066MHz/QR) S26361-F3604-E517 two DIMMs per channel = max. 1333MHz for 1.5V memory only 16GB (1333MHz/DR) S26361-F4492-E516 Special release for Dual Rank 16 GB DIMM Choose up to 18 order codes for SR/DR to enable 18x 16 GB configuration Choose up to 12 order codes for QR 6-9x for each CPU Registered (reg) LV RDIMMs (1.35V) Note 2.) with max. For "Independent Channel Mode" usage! LV Memory (1.35V) is only supported by 2/3 modules - One DDR3 LV RDIMM ECC memory module CPU Type *56xx per channel Note 3.) 4GB (1333MHz/DR) S26361-F4415-E514 Max. DDR3 memory speed 1333MHz is only 8GB (1333MHz/DR) S26361-F4415-E515 possible with CPU`s X56xx, providing 6.4GT/s QPI Note 4) Choose up to 12 order codes Mix of Standard Voltage (1.5V) and Low Voltage (1.35V) Memory modules is supported but not recommended In mixed mode, all Memory modules will run at Standard Voltage (1.5V) Unbuffered (ub) UDIMMs cannot be mixed with registered (reg ) RDIMMs Memory speed in all configurations with UDIMMs is max. 1333MHz depending on the used CPU speed Unbuffered (ub) UDIMMs (1.5V) Unbuffered (ub) LV UDIMMs (1.35V) For "Independent Channel Mode" usage! For "Independent Channel Mode" usage! 6x for each CPU - One DDR3-1333 PC3-10600 UB ECC mem. - One DDR3 LV 1333 PC3-10600 UB ECC mem. with max. on special release 3 modules 2GB (DR) S26361-F4413-E513 2GB (DR) S26361-F4416-E513 on special release per channel No Chipkill No Chipkill Choose up to 12 order codes Choose up to 12 order codes F1 F2 Fujitsu Technology Solutions x86 PRIMERGY Server 10 of 14
F1 F2 S26361-F3284-E1 (only available with 56xx CPUs) Spare Channel Mode Installation With this order code a BIOS setup for spare mode is factory preinstalled The three identical memory modules of following order codes are always equipped in one memory bank to use the Spare Channel Mode In this mode only two modules are active the third module is the spare module S26361-F3284-E2 Performance Mode Installation With this order code BIOS setup is default for highest performance The three identical memory modules of following order codes are always equipped in one memory bank to run with highest performance In this mode all three modules are active and full capacity can be used 2/3x for each CPU with max. 3 modules per channel Registered (reg) RDIMMs (1.5V) SP = for "Spare Channel and Performance Mode" usage! See Note 1.) - 4.) - Three DDR3 RDIMM ECC memory modules SP 6GB (3x 2GB 1333 MHz SR) S26361-F4412-E533 = 4GB usable memory for Spare Channel Mode = 6GB usable memory for Performance Mode SP 12GB (3x 4GB 1333 MHz DR) S26361-F4412-E534 = 8GB usable memory for Spare Channel Mode = 12GB usable memory for Performance Mode SP 24GB (3x 8GB 1333MHz DR) S26361-F4412-E535 = 16GB usable memory for Spare Channel Mode = 24GB usable memory for Performance Mode SP 48GB (3x 16GB 1066MHz QR) S26361-F4412-E536 = 32GB usable memory for Spare Channel Mode = 48GB usable memory for Performance Mode Choose up to 6 order codes for SR/DR Choose up to 4 order codes for QR Registered (reg) LV RDIMMs (1.35V) SP = for "Spare Channel and Performance Mode" usage! See Note 1.) - 4.) - Three DDR3 LV RDIMM ECC memory modules SP 12GB (3x 4GB 1333 MHz DR) S26361-F4415-E534 = 8GB usable memory for Spare Channel Mode = 12GB usable memory for Performance Mode SP 24GB (3x 8GB 1333MHz DR) S26361-F4415-E535 = 16GB usable memory for Spare Channel Mode = 24GB usable memory for Performance Mode Choose up to 4 order codes G1 G2 Fujitsu Technology Solutions x86 PRIMERGY Server 11 of 14
G1 G2 S26361-F3284-E3 Mirrored Channel Mode Installation With this order code a BIOS setup for Mirrored Channel Mode is factory preinstalled The two identical memory modules of following order codes are always equipped in one memory bank to use the Mirrored Channel Mode In this mode only one module contains active data, the second modul contains the mirrored data Registered (reg) RDIMMs (1.5V) MM = for "Mirrored Channel Mode" usage! See Note 1.) - 4.) - Two DDR3 RDIMMs ECC memory modules MM 4GB (2x 2GB 1333MHz SR) S26361-F4412-E523 = 2GB usable for Mirrored Channel Mode MM 8GB (2x 4GB 1333MHz DR) S26361-F4412-E524 = 4GB usable for Mirrored Channel Mode MM 16GB (2x 8GB 1333MHz DR) S26361-F4412-E525 = 8GB usable for Mirrored Channel Mode MM 32GB (2x 16GB 1066MHz QR) S26361-F4412-E526 = 16GB usable for Mirrored Channel Mode Choose up to 6 order codes for SR/DR Choose up to 4 order codes for QR 2/3x for each CPU with max. 3 modules Registered (reg) LV RDIMMs (1.35V) per channel MM = for "Mirrored Channel Mode" usage! See Note 1.) - 4.) - Two DDR3 LV RDIMM ECC memory modules MM 8GB (2x 4GB 1333MHz DR) = 4GB usable for Mirrored Channel Mode MM 16GB (2x 8GB 1333MHz DR) = 8GB usable for Mirrored Channel Mode Choose up to 4 order codes S26361-F4415-E524 S26361-F4415-E525 H Fujitsu Technology Solutions x86 PRIMERGY Server 12 of 14
H System configurator and order-information guide Section XIV irmc S2, Graphics Graphic Controller is part of the onboard Management Controller irmc S2. Other graphics are not possible. The irmc S2 advanced pack is included in the system delivery. A corresponding license order is not necessary. Section XV Mezzanine cards for Dual Socket Server Blade The Dual Server Blade supports the following optional mezzanine cards. A Fibre Channel Switch / Pass-Thru blade, an Ethernet LAN Switch / Pass-Thru blade, SAS Switch respectively an InfiniBand switch is required in the system unit for this functionality. SAS Mezz Cards require an SAS switch for each SAS link SAS Mezz Cards has to be installed in Mezz Card slot 2 on Server Blade 1x S26361-F4481-E1 S26361-F4480-E1 PY SAS RAID Mezz Card 6Gb PY SAS HBA Mezz Card 6Gb MegaRAID HBA SAS 2.0 SAS 2.0 pluggable on the main board pluggable on the main board PCIe Gen2 interface PCIe Gen2 interface 4x SAS links to midplane 4x SAS links to midplane 2x SAS links to internal HDD's max. 1x per Server Blade max. 1x per Server Blade S26361-F4481-E10 RAID Mezz ibbu Upgrade ibbu08 Li-Ion max. 1x per Mezz Card Requires an Ethernet LAN Requires a Fibre Channel Requires an InfiniBand Switch, IBP or Pass-Thru Switch for each channel. Switch for each Mezz Card. Blade for each channel. S26361-F3331-E1 S26361-F3874-E1 S26361-F3992-E2 PY Eth Mezz Card 1Gb 4 Port PY FC Mezz Card 8Gb 2 Port PY IB CX2 Mezz Card 40Gb 2 Port 2x Intel Zoar controller Emulex LPe12002 compatible Interface to midplane: 4x 10/100/1000 Mbit/s. pluggable on the main board, 2x 10Gb/s(SDR), 2x 20Gb/s(DDR) pluggable on the main board, MC-FC82E 2x 40Gb/s(QDR) Four channel 1Gbit/s Dual channel 8Gbit/s each Dual channel 40Gbit/s each PCIe x4 Interface PCIe x8 interface PCIe x8 interface max. 2x per Server Blade max. 2x per Server Blade max. 2x per Server Blade S26361-F3997-E1 PY Eth Mezz Card 10Gb 2 Port Intel 82599EB LAN Controller 2x 10Gbit/s. 0-2x pluggable on the main board, Dual channel 10Gbit/s PCIe x8 Interface iscsi boot planned max. 2x per Server Blade S26361-F3592-E502 PY CNA Mezz Card 10Gb 2 Port Emulex OCe10102 compatible 2x 10Gbit/s DCB/FCoE pluggable on the main board, Dual channel 10Gbit/s PCIe x8 Interface max. 2x per Server Blade R S T U V R: see separate BX900 System Unit configurator, sheet "1 GB Ethernet" S: see separate BX900 System Unit configurator, sheet "10 GB Ethernet" T: see separate BX900 System Unit configurator, sheet "Fibre Channel" U: see separate BX900 System Unit configurator, sheet "InfiniBand" V: see separate BX900 System Unit configurator, sheet "SAS" https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/pages/default.aspx Fujitsu Technology Solutions x86 PRIMERGY Server 13 of 14
Change Report Date Order number Changes S26361-F5123-E*00 New order for SATA SSD s will not be released 2012-02-29 S26361-F4492-E516 corrected Speed to 1333 2011-11-12 S26361-F3604-E517 corrected 32 GB DIMM Number 12.10.2011 added 32 GB DIMM 2010-01-10 S26361-F4514-E160 Westmere-EP Refresh CPUs added 2010-12-16 Updated USB section 2010-12-09 Added 16 GB DR DIMMs as special release 2010-12-03 Removed HDD support - HDD on special release only 2010-11-19 Added HDD support 2010-09-30 S26361-F3592-E502 Added new CNA Mezz Card - as soon as available 2010-09-07 S26361-F4478-L1 Added Frontside Kabel 2010-06-01 First release Fujitsu Technology Solutions x86 PRIMERGY Server 14 of 14