Xitanium LED driver Datasheet Xitanium LED drivers Sensor Ready Simplifying connectivity solutions with sensors and controls Philips Sensor Ready drivers are ideal for use with sensors and building management systems. With its integrated power supply based on DALI 2.0 it is easy to power sensors and wireless modules directly from the driver. It also features integrated energy metering for use in building management systems from the SR ertified partner program. This program with key building management and sensor vendors ensures that certified sensors and controllers work seamlessly with the Xitanium SR driver. enefits Features Application Sensor Ready concept, ideal for use LED specs comparable to TD isolated drivers office with sensors & building management systems Integrated power supply over DALI 2.0 to power sensors and wireless radios directly from the driver, open spec for all OEMs, simplifying integration of sensors into the luminaire Integrated power metering for use in building management systems from certified partners ~15V DALI current source power supply, max 0.5 W for sensors and radios Highly accurate power metering, accessible over DALI
Electrical input data Rated input voltage range 220...240 Vac Rated input voltage 230 Vac Rated input frequency range 50...60 Hz Rated input current 0.2 A @ full output power @ rated input voltage Rated input power 42 W @ rated output power @ rated input voltage Power factor 0.9 Total harmonic distortion 20 @ rated output power @ rated input voltage Efficiency 87 @ full output power @ rated input voltage Rated input voltage D range 186...250 Vdc Rated input current D range 0.2 Adc Input voltage A range 202...254 Vac Operational range Input frequency A range 47.5...63 Hz Operational range Input voltage D range 168...275 Vdc Operational range Standby Power (TD) 0.5 W Isolation input to output @ rated output power @ rated input voltage Electrical output data Regulation method onstant urrent Output voltage 27...54 Vdc Output voltage max. 60 V Peak voltage at open load Output current 0.3...1 A Full output current setting Output current min prograable 300 ma Output current min diing 7 ma Output current tolerance ±5 Output current ripple LF 4 Output current ripple HF 4 Output power 10...36 W Full output ontrol method DALI Diing range 1...100 Absolute minimum diing current: 7mA Galvanic Isolation Double Ripple = peak / average Electrical data controls input Logistical data Product name Order code 871869656771500 Logistic code 12N 9290 015 16306 EAN3 8718696567722 Pieces per box 12 2/7
Wiring & onnections Input wire cross-section 0.5...1.5 2 16...20 AWG Input wire strip length 8...9 Output wire cross-section 0.5...1.5 2 16...20 AWG Output wire strip length 8...9 Maximum cable length 2000 Total length of wiring including LED module, one way Insulation Insulation input input output SR-input Housing Double output SR-input Double Housing Dimensions and weight Length (A1) 360 Width (1) 30 Height (1) 21 Fixing hole diameter (D1) 4.1 Fixing hole distance (A2) 350 Weight 260 gram 3/7
Operational temperatures and humidity Ambient temperature -25...+50 Higher ambient temperature allowed as long as Tcase-max is not Starting Ambient temperature -25...+50 Tcase-max 75 Maximum temperature measured at Tcase-point Tcase-life 75 Measured at Tcase-point Maximum housing temperature 110 In case of a failure Relative humidity 10...90 Non-condensing Ambient temperature -25...+85 Relative humidity 5...95 Non-condensing Driver lifetime 50,000 hours Measured temperature at Tcase-point is Tcase-life. exceeded. Storage temperature and humidity Lifetime Maximum failures = 10 Prograable features Remark Set output current (AO) LEDset, Manual, SimpleSet See Design-in guide. Default output current: 300 ma onstant Lumen Over Lifetime (LO) D emergency diing (DemDIM) orridor mode Energy metering Diagnostics 4/7 urrent output by default decreased to 15 See Design-in guide Default: T1=55s, T2=12s, T3=30min Accuracy = 4
Features Open load protection Remark Automatic recovering Short circuit protection Automatic recovering Over power protection Automatic recovering Hot wiring No Suitable for fixtures with protection class I and II per IE60598 ertificates and standards Approval marks / E / ENE Ingress Protection classification 20 Inrush current Inrush current Ipeak 26 A Input voltage 230V Inrush current Twidth 140 µs Input voltage 230V, measured at 50 Ipeak Drivers / M 16A type 24 pcs M Rating Relative number of LED drivers 10A 63 13A 81 16A 100 (stated in datasheet) 20A 125 25A 156 10A 104 13A 135 16A 170 20A 208 25A 260 Driver touch current / protective conductor current Typical touch current (ins. lass II) < 0.4 ma peak Acc. IE61347-1. LED module contribution not included Mains surge iunity (diff. mode) 1 Acc. IE61000-4-5. 2 Ohm, 1.2/50us, 8/20us Mains surge iunity (co. mode) 2 Acc. IE61000-4-5. 12 Ohm, 1.2/50us, 8/20us ontrol surge iunity (diff. mode) 1 Acc. IE61000-4-5. 2 Ohm, 1.2/50us, 8/20us ontrol surge iunity (co. mode) 2 Acc. IE61000-4-5. 12 Ohm, 1.2/50us, 8/20us Default setting Remark AO 300 ma Surge iunity Additional information 5/7
Graphs Operating window Power factor versus output power Efficiency versus output power 6/7
THD versus output power Notes This product includes software licensed under terms that require Philips Lighting Holding.V. to display the following notice: ASF: Release ASF-3.32 The Atmel Software Framework (ASF, www.atmel.com/asf) is a compilation of embedded software for Atmel flash MUs: megaavr, AVR XMEGA, AVR U3 and SAM devices. It has been designed to help develop and glue together the different components of a software design. It can easily integrate into an operating system (OS) or run as a stand-alone product. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of Atmel may not be used to endorse or promote products derived from this software without specific prior written permission. 4. This software may only be redistributed and used in connection with an Atmel microcontroller product. THIS SOFTWARE IS PROVIDED Y ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INLUDING, UT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERHANTAILITY, FITNESS FOR A PARTIULAR PURPOSE AND NON-INFRINGEMENT ARE EXPRESSLY AND SPEIFIALLY DISLAIMED. IN NO EVENT SHALL ATMEL E LIALE FOR ANY DIRET, INDIRET, INIDENTAL, SPEIAL, EXEMPLARY, OR ONSEQUENTIAL DAMAGES (INLUDING, UT NOT LIMITED TO, PROUREMENT OF SUSTITUTE GOODS OR SERVIES; LOSS OF USE, DATA, OR PROFITS; OR USINESS INTERRUPTION) HOWEVER AUSED AND ON ANY THEORY OF LIAILITY, WHETHER IN ONTRAT, STRIT LIAILITY, OR TORT (INLUDING NEGLIGENE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIILITY OF SUH DAMAGE. 2017 Philips Lighting Holding.V. All rights reserved. This document contains information relating to the Philips Lighting portfolio, intended for companies who may be interested in developing their product offering. Note that the information provided is subject to change. Philips Lighting does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any coercial offer and does not form part of any quotation or contract. Date of release: November 28, 2017 v1 www.philips.com/technology