Description The is low capacitance transient voltage suppressor array for high speed data interface that designed to protect sensitive electronics from damage or latch-up due to ESD lightning, and other voltage induced transient events. All pins are rated to withstand 16kV ESD pulses using the IEC 61-4-2 air discharge method, which can meet the requirement of level 4. S Feature Applications 1 9 8 7 1 2 3 4 6 5 11W peak pulse power (t P = 8/2μs) DFN-1 Package Working voltage: 3.3V Low clamping voltage Low capacitance RoHS compliant Transient protection for data lines to IEC 61-4-2(ESD) ±16KV(air), ±16KV(contact); IEC 61-4-4 (EFT) 4A (5/5ns) IEC 61-4-5 (Lightning) 5A (8/2us) USB 2.,3. Power & Data Line Protection DVI & HDMI Port Protection Serial ATA Port Protection Mobile Handsets Digital Cameras and camcorders PDA & MP3 Players Digital TV and Set-top Boxes Other Portable Electronic Components Mechanical Characteristics Lead finish:1% matte Sn(Tin) Mounting position: Any Qualified max reflow temperature:26 Device meets MSL 1 requirements Pure tin plating: 7 ~ 17 um Pin flatness: 3mil Electronics Parameter Symbol V RWM Parameter Peak Reverse Working Voltage I I R V BR I T Reverse Leakage Current @ V RWM Breakdown Voltage @ I T Test Current I F I PP Maximum Reverse Peak Pulse Current V C V BR V RWM V V C P PP C I F Clamping Voltage @ I PP Peak Pulse Power Junction Capacitance Forward Current I R V F I T I PP V F Forward Voltage @ I F Rev.6.1 1 www.prisemi.com
Electrical characteristics per line@( unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Units Peak Reverse Working Voltage V RWM 3.3 V Breakdown Voltage V BR I t = 1mA 5.6 7. V Reverse Leakage Current I R V RWM =3.3V, T=25 1. μa Clamping Voltage V C I PP = 1A, t P = 8/2μs 8. 9. V Clamping Voltage V C I PP=5A, t P = 8/2μs 11 12.5 V Clamping Voltage V C I PP=7.5A, t P = 8/2μs 14 16 V Junction Capacitance(IO-IO) C J V R=V, f = 1MHz.3.4 pf Junction Capacitance(IO-GND) C J V R=V, f = 1MHz.6.8 pf Absolute maximum rating@25 Rating Symbol Value Units Peak Pulse Power (t p=8/2μs) P pp 11 W Operating Temperature T J -55 to +15 Storage Temperature T STG -55 to +15 Typical Characteristics IPP Peak Pulse Current - % of IPP 1 8 6 4 2 t f=8μs t P =2μs(I PP /2) Test Waveform Parameters t f=8us t p=2us % Of Rated Power 1 8 6 4 2 5 1 15 2 25 3 t - Time -μs 25 5 75 1 125 15 T L Lead Temperature - Fig 1.Pulse Waveform Fig 2.Power Derating Curve Rev.6.1 2 www.prisemi.com
VC - Clamping voltage (V) 14 12 1 8 Pulse waveform : =8/2µs CJ - Junction capacitance (pf).65.6.55.5.45.4 Any I/O pin to GND Between any I/O pin f=1mhz 6 2 4 6 8 IPP - Peak pulse current (A) Fig 3. Clamping voltage vs. Peak pulse current.35 1 2 3 4 5 VR - Reverse voltage (V) Fig 4. Capacitance vs. Reveres voltage 1 3 24 Peak Pulse Power (W) 1 1 TLP Current (A) 18 12 RD=.48Ω 6 1 1 1 1 1 Pulse Duration(us) Fig 5.Non Repetitive Peak Pulse Power vs. Pulse time 5 1 15 2 25 TLP Voltage (V) Fig 6. TLP Measurement Solder Reflow Recommendation Peak Temp=257, Ramp Rate=.82deg. /sec 28 24 2 16 12 8 4 3 6 9 12 15 18 21 24 27 3 33 36 39 42 45 48 Rev.6.1 3 Time (sec) www.prisemi.com
PCB Design For TVS diodes a low-ohmic and low-inductive path to chassis earth is absolutely mandatory in order to achieve good ESD protection. Novices in the area of ESD protection should take following suggestions to heart: Do not use stubs, but place the cathode of the TVS diode directly on the signal trace. Do not make false economies and save copper for the ground connection. Place via holes to ground as close as possible to the anode of the TVS diode. Use as many via holes as possible for the ground connection. Keep the length of via holes in mind! The longer the more inductance they will have. Product dimension (DFN-1) A B C D E H F G 1 R:.125 1 J L K Rev.6.1 4 www.prisemi.com
Dim Millimeters Inches MIN MAX MIN MAX A 2.4 2.6.94.12 B.9 1.1.35.43 C.13.5 D..5..2 E.5.65.2.26 F.45.55.17.22 G.3.425.12.17 H.35.45.14.18 J.5 BSC.2 BSC K 1.2 1.3.47.56 L.15.25.6.1.2.4.6.2.6.5.5 Unit:mm Marking information.324 Ordering information Device Package Reel Shipping DFN-1 (Pb-Free) 7" 3 / Tape & Reel Rev.6.1 5 www.prisemi.com
IMPORTANT NOTICE and are registered trademarks of Prisemi Electronics Co., Ltd (Prisemi),Prisemi reserves the right to make changes without further notice to any products herein. Prisemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Prisemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in Prisemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. Prisemi does not convey any license under its patent rights nor the rights of others. The products listed in this document are designed to be used with ordinary electronic equipment or devices, Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. Website: http://www.prisemi.com For additional information, please contact your local Sales Representative. Copyright 29, Prisemi Electronics is a registered trademark of Prisemi Electronics. All rights are reserved. Rev.6.1 6 www.prisemi.com