REACH IP65 Product overview Motion Control products integrate 1.8 2-phase stepper motor, fully programmable motion controller, drive electronics and optional encoder. Products with encoders include stall detection, position maintenance, and find index mark. Programming for these stand-alone motion control solutions is via RS-422/485 interface with MCode software using simple 1 to 2 character instructions. ModbusTCP protocol is also available. system components eliminates multiple potential failure points, and lowers risk of electrical noise by eliminating cabling between motor and drive. These compact, powerful and cost effective motion control solutions deliver exceptional smoothness and performance that can reduce system cost, design and assembly time for a large range of 2- phase stepper motor applications. Application areas products deliver reliable performance for new and existing motion control applications. Satisfying the requirements for a wide range of machine builders. Simplify your machine design and reduce cabinet size by replacing multiple components with a single compact integrated motor. Fewer individual MDI 23 programmable Motion Control products: integrated NEMA23 motor and controls, IP65 & IP20-rated General features Compact integrated microstepping drive, programmable motion controller and NEMA23 1.8 2-phase stepper motor Advanced current control for exceptional performance and smoothness +12 to +75 VDC single supply 20 microstep resolutions up to 51,200 steps per rev including: Degrees, Metric, Arc Minutes Auxiliary logic power supply input 0 to 5 MHz step clock rate selectable in 0.59 Hz increments Up to 8 I/O lines One 10 bit selectable analog input Communication RS-422/485; ModbusTCP (1) Protection IP20, IP65 ratings Programmable Motor run / hold current Available options Motor stack lengths Long life linear actuators (2) Connector options Encoders Rear control knob for manual positioning Graphical user interface provided for quick and easy parameter setup (1) Only available for Plus 2 IP20 products. (2) Refer to MDrive Linear Actuator documentation. Official UK & Ireland Distributor Intelligent motion systems
Specifications Communication Protocol type RS-422/485 4.8 to 115.2 kbps baud rate ModbusTCP Only available with NEMA23 Plus 2 products Input power Voltage VDC +12...+75 for motor stack lengths: single, double, triple +12...+60 for motor stack length: quad Current maximum (1) Amp 2.0 for motor stack lengths: single, double, triple Motor Frame size NEMA 23 inches 2.3 mm 57 Holding torque oz-in 90...283 N-cm 64... 200 Length stack sizes 1, 2, 3 & 4 Thermal Operating temp Heat sink maximum 85 C non-condensing Motor maximum 100 C Protection Type IP rating IP20, IP65 I/O warnings 3.5 for motor stack length: quad Over temp, short circuit, transient, over voltage, inductive clamp Auxiliary logic input Voltage range +12 to + When input voltage is removed, maintains power only to control and feedback circuits. (2) Analog input Resolution 10 bit Voltage range General purpose I/O Output sinking current Up to 600 ma Plus products Number 4 Type 0 to +5 VDC, 0 to +10 VDC, 0-20 ma, 4-20 ma Sourcing or sinking inputs, or sinking outputs Logic range Inputs and outputs tolerant to +, inputs TTL level compatible Plus 2 products Number 8 or 4 (3) Type Sourcing or sinking outputs/inputs Logic range Sourcing outputs +12 to +, inputs and sinking outputs tolerant to +24 VDC, inputs TTL level compatible Motion Open loop configuration Number of settings 20 Steps per revolution 200, 400, 800, 1000, 1600, 2000, 3200, 5000, 6400, 10000, 12800, 20000, 25000, 25600, 40000, 50000, 51200, 36000 (0.01 deg/µstep), 21600 (1 arc minute/µstep), 25400 (0.001mm/µstep) Counters Type Position, encoder / 32 bit Edge rate maximum 5 MHz Velocity Range +/ 5,000,000 steps per second Resolution 0.5961 steps per second Accel/Decel Range 1.5 to 10 9 steps per second 2 Resolution 90.9 steps per second 2 Position feedback Optional Encoder required Expanded motion Electronic gearing Range 0.001 to 2.000 Plus 2 products only external clock in (4) Resolution 32 bit Threshold TTL High speed I/O Position capture Input filter range 50 ns to 12.9 µs (10 MHz to 38.8 khz) Trip output Resolution 32 bit Speed 150 ns Resolution 32 bit Threshold TTL Position feedback Optional Remote encoder interface required Software Program storage Type/size Flash/6384 bytes User registers User program labels & variables 192 Math functions Branch functions Four 32 bit +., x,, >, <, <=, >=, AND, OR, XOR, NOT Branch and Call General purpose Inputs home, limit plus, limit minus, go, stop, pause, jog plus, jog minus, general purpose I/O functions Outputs moving, fault, stall, velocity change, general purpose Trip functions Party mode addresses 62 (2) Encoder functions (1) Actual power supply current will depend on voltage and load. (2) Not available with ModbusTCP products. (3) I/O is reduced from 8 to 4 for products with remote encoder option or ModbusTCP protocol. (4) Adjusting the microstep resolution can increase the range. See User Manual for complete details: www.motion.schneider-electric.com/manuals.html Trip on input, trip on position, trip on time, trip capture, trip on relative position Stall detection, position maintenance, find index 2 MDrive products assembled in USA
Dimensions MDI 23 NEMA23 motor, IP20-rated inches (mm) 1.90 0.81 ±0.02 (48.3) (20.6 ±0.5) P1 0.063 ±0.008 (1.6 ±0.2) 0.59 ±0.008 Length Motors: (15.0 ±0.2) Ø 0.2500 +0/-0.0005 (Ø 6.350 +0/-0.013) 2.02 (51.2) 1.63 (41.4) Ø 0.197 +0.012/- 0 (Ø 5.0 +0.3/-0) 2.96 Quad Length Motor: (75.2) Ø 0.315 +0/-0.0005 (Ø 8.0 +0/-0.013) Option P2 0.93 P2: RJ45 ( 23.6) Length Motors: 0.230 ±0.004 (5.8 ±0.1) Quad Length Motor: 0.86 1.34 0.189 ±0.012 0.2756 ±0.004 (21.8) (34.0) L MAX (4.8 ±0.3) (7.0 ±0.1) L MAX2 L MAX1 Motor stack length Lmax Lmax1 (1) Lmax2 Single 2.65 (67.31) 2.85 (72.39) 3.36 (85.34) Double 3.02 (76.71) 3.22 (81.79) 3.73 (94.74) Triple 3.88 (98.55) 4.08 (103.63) 4.59 (116.59) Quad 5.28 (134.15) 5.48 (139.19) 5.99 (152.19) 1.856 ±0.008 ( 47.1 ±0.2) 2.22 ( 56.4) Ø 1.500 ±0.002 (Ø 38.1 ±0.1) (1) Grounding screw is not present on all products. P1/P3 connector options P2 connector options Lmax2 option I/O & Power I/O & Power 0.44 12.00 (11.2) (304.8) I/O, Power & Remote encoder Plus2 products only 0.50 (12.7) 0.13 (3.3) RS-422/485 Communication RS-422/485 Communication ModbusTCP Communication P2 P2 P2 Ø 0.97 (Ø 24.6) P1 P1 0.38 P1/P3 (9.7) flying leads pluggable 7-pin 12.0" (305mm) non-locking spring clamp terminal strip wire crimp 14- & 2-pin locking IDC wire crimp RJ45 control knob 20 in-lb / 10-pin non-locking 10-pin friction lock 225 N-cm max torque MDI 23 NEMA23 motor, IP65-rated inches (mm) Communication L 2.02 MAX3 (51.2) 2.04 0.81 ±0.02 1.63 (51.9) 0.06 (20.6 ±0.5) (41.4) (1.5) Ø 0.53 0.59 ±0.008 Ø 0.197 +0.012/-0 (Ø 13.5) 2.96 (15.0 ±0.2) (Ø 5.0 +0.3/-0) 5-pin M12 (female) (75.2) P2 industrial connector I/O, Power & Remote encoder P1 Ø 0.87 1.033 Length Motors: (Ø 22.1) (26.2) 0.230 ±0.004 19-pin M23 (male) (5.8 ±0.1) industrial connector 1.856 ±0.008 ( 47.1 ±0.2) Length Motors: Ø 0.2500 +0/-0.0005 (Ø 6.350 +0/-0.013) 1.48 0.189 ±0.012 (37.6) L (4.8 ±0.3) 2.22 MAX ( 56.4) L MAX2 Motor stack length Lmax Lmax2 Lmax3 Single 2.82 (71.63) 3.48 (88.39) 3.42 (86.87) Double 3.16 (80.26) 3.82 (97.03) 3.76 (95.5) Triple 4.02 (102.11) 4.67 (118.62) 4.62 (117.35) Ø 1.500 ±0.002 (Ø 38.1 ±0.1) www.motion.schneider-electric.com 3
Accessories non-locking IDC mating connector MD-CC400-001 in-line converter USB connector description length part number feet (m) QuickStart Kit For rapid design verification, all-inclusive QuickStart Kits includes prototype development cables and a communication converter for initial functional setup and system testing. For all MDrive23 programmable Motion Control products add "K" to part number 10-pin friction lock mating connector in-line converter USB connector Communication converter Electrically isolated, in-line converter pre-wired with mating connector to conveniently set/program communication parameters for a single via a PC's USB port. MD-CC402-001 5-pin M12 mating industrial connector 5-pin M12 (male) MD-CC401-001 PD10-1434-FL3 friction lock mating connector in-line converter USB connector Mates to 10-pin non-locking IDC connector Mates to 10-pin friction lock wire crimp connector Mates to 5-pin female M12 industrial connector Prototype development cable Speed test/development with pre-wired mating connector with other cable end open. Mates to 10-pin locking wire crimp connector for I/O and remote encoder option Mates to 14-pin locking wire crimp connector for I/O and remote encoder option Mates to 2-pin locking wire crimp connector for power Mates to 19-pin male M23 industrial connector with straight termination for I/O, power and remote encoder option Mates to 19-pin male M23 industrial connector with right angle termination for I/O, power and remote encoder option 12.0 (3.6) MD-CC400-001 12.0 (3.6) MD-CC402-001 12.0 (3.6) MD-CC401-001 10.0 (3.0) PD10-1434-FL3 10.0 (3.0) PD14-2334-FL3 10.0 (3.0) PD02-2300-FL3 13.0 (4.0) MD-CS100-000 13.0 (4.0) MD-CS101-000 locking mating connector PD14-2334-FL3 locking mating connector PD02-2300-FL3 Mating connector kits Connectors for assembly of cables, cable material not supplied. Sold in lots of 5. Manufacturer's crimp tool recommended for crimp connectors. 10-pin friction lock wire crimp connector for communication CK-02 10-pin non-locking IDC connector for communication CK-01 14-pin locking wire crimp connector for I/O and remote CK-09 encoder option 2-pin locking wire crimp connector for power CK-04 19-pin M23 (female) industrial mating connector 2.8 / 71.5 mm MD-CS100-000 Drive protection module Limits surge current and voltage to a safe level when DC input power is switched on-and-off to an. For all MDrive23 programmable Motion Control products DPM75 4 MDrive products assembled in USA
Part numbers MDrive 23 Plus IP20 MDrive 23 Plus 2 IP20 MDrive 23 Plus 2 IP65 with industrial connectors P1: I/O & Power F = 12" flying leads P = non-locking spring clamp terminal strip P2: Communication D = RS-422/485 with 10-pin IDC non-locking connector L = RS-422/485 with 10-pin friction lock wire crimp connector P1: I/O, and optional remote encoder C = 14-pin locking wire crimp connector P3: Power 2-pin locking wire crimp connector P2: Communication D = RS-422/485 with 10-pin IDC non-locking connector L = RS-422/485 with 10-pin friction lock wire crimp connector R = ModbusTCP with RJ45 locking connector P2: Communication Q = RS-422/485 with 5-pin M12 female industrial connector P1: I/O & Power, and optional remote encoder M = 19-pin M23 male industrial connector IP20-rated products example part number K M D I 1 F R D 2 3 A 7 N QuickStart Kit K M D I 1 F R D 2 3 A 7 N K = kit option, omit from part number if unwanted MDrivePlus version K M D I 1 F R D 2 3 A 7 N MDI = Intelligent programmable Motion Control Input K M D I 1 F R D 2 3 A 7 N 1 = Plus version with standard features 3 = Plus 2 version with expanded features P1 connector K M D I 1 F R D 2 3 A 7 N F = flying leads P = pluggable C = wire crimp (1) Communication type K M D I 1 F R D 2 3 A 7 N R = RS-422/485 E = ModbusTCP (1) P2 connector K M D I 1 F R D 2 3 A 7 N D = IDC L = wire crimp R = RJ45 (2) Motor size K M D I 1 F R D 2 3 A 7 N 23 = NEMA 23 2.3" / 57mm Motor length K M D I 1 F R D 2 3 A 7 N A = single stack B = double stack C = triple stack D = quad stack Drive voltage (3) K M D I 1 F R D 2 3 A 7 N 7 = +12 to +75 VDC 6 = +12 to +60 VDC Options omit from part number if unwanted N N = rear control knob for manual positioning EQ = internal 512-line magnetic encoder w/ index mark EE (1) = remote differential encoder interface; encoder not supplied (1) Only available with Plus 2 products. (2) Only available with ModbusTCP products. (3) Only quad stack motors have +12 to +60 VDC drives, all other motors have +12 to +75 VDC drives. IP65-rated products example part number K M D I 4 M R Q 2 3 A 7 EQ QuickStart Kit K M D I 4 M R Q 2 3 A 7 EQ K = kit option, omit from part number if unwanted MDrivePlus version K M D I 4 M R Q 2 3 A 7 EQ MDI = Intelligent programmable Motion Control Input K M D I 4 M R Q 2 3 A 7 EQ 4 = Plus 2 version with expanded features P1 connector K M D I 4 M R Q 2 3 A 7 EQ M = M23 industrial connectors Communication type K M D I 4 M R Q 2 3 A 7 EQ R = RS-422/485 P2 connector K M D I 4 M R Q 2 3 A 7 EQ Q = M12 industrial connector Motor size K M D I 4 M R Q 2 3 A 7 EQ 23 = NEMA 23 2.3" / 57mm Motor length A = single stack B = double stack C = triple stack Drive voltage 7 = +12 to +75 VDC Options omit from part number if unwanted EQ = internal 512-line magnetic encoder w/ index mark EE = remote differential encoder interface; encoder not supplied K M D I 4 M R Q 2 3 A 7 EQ K M D I 4 M R Q 2 3 A 7 EQ EQ Validatewww.motionpart.schneidernumberswith-electricMDRIVE.com PART BUILDER, an easy-to-use online tool at: motion.schneider-electric.com/mdrive_part_builder/ 5
Motor performance MD 23 NEMA 23 motor specifications Motor Stack length Single Double Triple Quad Holding torque oz-in 90 144 239 283 N-cm 64 102 169 200 Detent torque oz-in 3.9 5.6 9.7 14.2 N-cm 2.7 3.9 6.9 10.0 Rotor inertia oz-in-sec 2 0.0025 0.0037 0.0065 0.0108 kg-cm 2 0.18 0.26 0.46 0.76 Weight (motor+driver) oz 21.6 26.4 39.2 62 g 612 748 1111 1746 MD 23 NEMA 23 speed torque (1) Single stack length Double stack length 75 VDC 75 VDC Triple stack length Quad stack length 75 VDC 60 VDC (1) Test conditions: 100% current with damper simulating load. Schneider Electric Motion USA 370 North Main Street Marlborough, CT 06447 www.motion.schneider-electric.com UK & Ireland Distributor: Motion Control Products Ltd. 11-15 Francis Avenue, Bournemouth, Dorset, UK BH11 8NX Tel.: +44 (0)1202 599922 Fax: +44 (0)1202 599955 www.motioncontrolproducts.com Intelligent motion systems Schneider Schneider Electric Motion USA Product Disclaimer and most recent product information online. June 2016