8502 Apple imac Stand for Winston Workstation Installation Instructions PAGE 1 OF 4 2015 Innovative Office Products, LLC P512127 REV A
8502 Apple imac Stand for Winston Workstation Parts List A Shelf Bracket 111604-124 D Shelf 111629-124 B Enclosure 111603-124 E Cover 111605-248 C #6 x 3/4" FHPhS 711880 PAGE 2 OF 4
1 2 Place the platform base on the work surface. Align the platform tabs at the back of the work surface as shown. A C B PAGE 3 OF 4
3 Choose from three height settings for your imac. D D OR OR D Note: In the lowest height setting, the shelf (item D) can be placed in one of the shelf positions, to be used at a later date, if desired. 4 i E PAGE 4 OF 4
WNST-APL-1 & WNST-APL-2 Winston Workstation for Apple imac Installation Instructions STEP 1 COLUMN...Page 3 STEP 2 MOUNT...Page 4 4 1 STEP 3 WORK SURFACE...Page 5 5 7 STEP 4 BEAM...Page 6 STEP 5 MONITOR TILTER...Page 7 STEP 6 MONITOR CUPS...Page 8 STEP 7 CABLE MANAGEMENT...Page 9 3 6 NOTE: Depending on your Winston Workstation configuration, you may not receive all the parts shown within this instruction booklet. 2 Installation may require two people. PAGE 1 OF 10 2015 Innovative Office Products, LLC P512137 REV A
Depending on your Winston Workstation configuration, you may not receive all parts shown below. WNST-APL-1 & WNST-APL-2 Winston Workstation for Apple imac Parts List A Work Surface 411469 E Cable Retainer 111735 I Utility Tray 111445 M Column Cap 111275-708 Q M4 x 12mm PhPHS 702096 B Column 411470-M F 3/8-16 x 1" FHSCS 701124 J Beam (10" or 30") 412036 or 412037 N 10-32 x 3/8" PhPHS 702281 R Dog Washer 111230-603 C Felt Pad 111464 G 10-32 x 1" FHSCS 711467 K 1/8" Allen Wrench 701312 O 75/100 mm VESA Adapter 105587 S 10-32 x 1/2" FHSCS 711240 D Freestanding Base 111248 H Column Clamp 111040 L 7/32" Allen Wrench 701127 P Standard Monitor Tilter 405397 T Column Cable Clip 111203-708 PAGE 2 OF 10
STEP 1 COLUMN IMPORTANT: Do not pull excessively on cable doing so may result in accidental actuation of column. B A 1 2 3 i Confirm cable is properly seated into position. L Use 7/32" Allen wrench to press cable firmly into place. PAGE 3 OF 10
STEP 2 MOUNT 1 2 3 Hang base plate over edge of work surface to allow access to countersunk holes. Side of base plate with felt pads should be face down. Place work surface on base plate to aid as a counterbalance. C D 4 5 E Note the orientation of column cable exit and base plate cable should exit in direction as shown. F 7/32" PAGE 4 OF 10
STEP 3 WORK SURFACE 1 2 Slide utility tray onto work surface. Utility tray simply rests on top of work surface. Two people may be required to install work surface to column. One to hold the work surface and the second person to secure the column clamp. H I 1/8" G A i 1 3 IMPORTANT: Tighten bolts evenly. Work surface clamp should sit flush against the column, ensure there are no gaps. Also, it is important the work surface clamp is level. 4 2 PAGE 5 OF 10
STEP 4 BEAM 1 2 H J 1/8" G 3 4 i IMPORTANT: Tighten bolts evenly. The beam should sit flush against the column, ensure there are no gaps. Also, it is important the work surface clamp is level. M 1 3 4 1/8" 2 K PAGE 6 OF 10
STEP 5 MONITOR TILTER 1 2 NOTE: Requires VESA compatible imac or Apple VESA adapter (not included). P O N Q PAGE 7 OF 10
STEP 6 1 MONITOR CUPS i 7/32" R 1/8" S PAGE 8 OF 10
STEP 7 CABLE MANAGEMENT 1 T PAGE 9 OF 10
HEIGHT ADJUSTMENT Press button and hold. Lift up/down. Release to lock in place. i Is your height adjust button not working? If so, make the adjustments below. 1 2 3 4 Slide workstation so that the work surface hangs over desk edge to allow access to underneath the work surface. Loosen the two screws as shown. Slide bracket in the direction shown and tighten screws. Test height adjust button readjust by repeating the steps above as necessary. PAGE 10 OF 10