Rev. 053116 Installation Guide Versatile Access Power and Integration Enclosures Trove1C1 Trove2CV2 - Trove1 enclosure with - Trove2 enclosure with /CDVI backplane (TC1) /CDVI backplane (TCV2) TC1 TCV2 - /CDVI backplane only - /CDVI backplane only Overview: Trove1C1 and Trove2CV2 accommodate various combinations of CDVI boards with or without power supplies and accessories for access systems. Specifications: 19 Gauge grey enclosure with ample knockouts for convenient access. Trove1C1 - Trove1 enclosure with TC1 /CDVI backplane. Includes: tamper switch, cam lock, lock nuts and mounting hardware. Enclosure Dimensions (H x W x D): 18 x 14.5 x 4.6255 (457mm x 368mm x 118mm) TC1 - TC1 /CDVI backplane. 19 Gauge backplane. Includes mounting hardware. Dimensions (H x W x D): 16.625 x 12.5 x 0.3125 (422.275mm x 317.5mm x 7.9mm) TC1 Backplane accommodates a combination of the following: One (1) AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eflow4nb, eflow6nb, eflow102nb or eflow104nb. One (1) ACM4(CB), MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), VR6. Four (4) A22 modules. Trove2CV2 - Trove2 enclosure with TCV2 /CDVI backplane. Includes: tamper switch, cam lock, lock nuts and mounting hardware. Enclosure Dimensions (H x W x D): 27.25 x 21.75 x 6.5 (692.15mm x 552.45mm x 165.1mm) TCV2 - TCV2 /CDVI backplane. 19 Gauge backplane. Includes mounting hardware. Dimensions (H x W x D): 25.375 x 19.375 x 0.3125 (644.525mm x 492.125mm x 7.9mm) TCV2 Backplane accommodates a combination of the following: Two (2) AL400ULXB2, AL600ULXB, AL1012ULXB, AL1024ULXB2, eflow4nb, eflow6nb, eflow102nb or eflow104nb. One (1) ACM8(CB), or two (2) MOM5, PD4UL(CB), PD8UL(CB), PDS8(CB), VR6. Five (5) A22 modules. Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI - 1 -
Installation Instructions: Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction. Product is intended for indoor use only. 1. Remove backplane from enclosure. Do not discard hardware. 2. Trove1C1 (Fig. 5, pg. 5) Mark and predrill holes on the wall to line up with the top two keyholes in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure s upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure s upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws. Trove2CV2 (Fig. 9, pg. 8) Mark and predrill holes on the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure s upper keyholes over the three upper screws, level and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws. 3. Mount UL Listed tamper switch (Included) (Ademco model 112 or equivalent) in desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2 from the right side (Fig. 1, pg. 1). Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate alarm signal open the door of the enclosure. 4. Mount /CDVI modules to TC1 or TCV2 backplane, refer to pages 3 and 6. Mounting Hardware: Plastic Standoff Metal Standoff 3/8 Pan Head Screw Honeywell model # 112 Tamper Switch or equivalent (provided) Enclosure to Access Control Panel or U.L. Listed Reporting Device Fig. 1 Edge of Enclosure - 2 - Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI
TC1: Configuration of Power Supply and/or Sub-Assembly Boards and CDVI Modules 1. Fasten standoffs (provided) to pems that match the hole pattern for Power Supply/Chargers or Sub-Assembly boards (Fig. 3, pg. 3). Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 3, pg. 3). 2. Mount boards to standoffs utilizing 5/16 pan head screws (provided) (Fig. 3, pg. 3). 3. Mount appropriate CDVI A22 modules into the correct positions (Fig. 3, pg. 3). by postioning standoffs over appropriate holes on the backplane and depress down on board to secure standoff to the backplane (Fig. 2, pg. 3). Note: CDVI A22 modules have one (1) RJ45 jack each. Please make sure that they are mounted correctly, as shown in Fig. 3 below. 4. Fasten TC1 backplane to Trove1 enclosure utilizing pan head screws (provided). Fig. 3 - Trove1C1/TC1 Configurations Plastic Stand Off pre-mounted into CDVI Atrium modules Insert into TC1/TCV2 backplane Fig. 2 Metal Standoff Placement Power Supply Sub- Assembly Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI - 3 -
Fig. 4 TC1 Dimensions 0.5 (12.7mm) 12.5 (321.31mm) 8.15 (207.01mm) 16.65 (422.9mm) 15.65 (397.5mm) 6.25 (158.75mm) 0.5 (12.7mm) - 4 - Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI
Fig. 5 Trove1C1 Enclosure Dimensions (H x W x D): 18 x 14.5 x 4.6255 (457mm x 368mm x 118mm) 7.25 (184.15mm) 14.5 (321.31mm) 1.45 (36.83mm) 1.948 (49.483mm) 4.5 (114.3mm) 13.0 (330.2mm) 1.5 (38.09mm) 0.5897 (14.98mm) 1.5 (38.09mm) 0.569 (14.52mm) 8.5 (215.9mm) 8.5 (215.9mm) 18.0 (457.2mm) 6.5 (165.1mm) 6.5 (165.1mm) 0.6012 (15.27mm) 1.0958 (27.83mm) 4.5 (114.3mm) 4.5 (114.3mm) 2.75 (69.85mm) 1.115 (28.32mm) 1.362 (34.59mm) Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI - 5 -
TCV2: Configuration of Power Supply and/or Sub-Assembly Boards and CDVI Modules 1. Fasten standoffs (provided) to pems that match the hole pattern for Power Supply/Chargers or Sub-Assembly boards (Fig. 7, pg. 6). Fasten metal standoffs in the correct locations to provide proper grounding, see below (Fig. 7, pg. 6). Note: sub-assembly position can accommodate either one (1) ACM8/ ACM8CB or two (2) PD4UL/PD4ULCB, PD8UL/PD8ULCB or MOM5. 2. Mount boards to standoffs utilizing 5/16 pan head screws (provided) (Fig. 7, pg. 6). 3. Mount appropriate CDVI A22 modules into the correct positions (Fig. 7, pg. 6). by postioning standoffs over appropriate holes on the backplane and depress down on board to secure standoff to the backplane (Fig. 6, pg. 6). Note: CDVI A22 modules have one (1) RJ45 jack each. Please make sure that they are mounted correctly, as shown in Fig. 7 below. 4. Fasten TCV2 backplane to Trove2 enclosure utilizing pan head screws (provided). Fig. 7 Plastic Stand Off pre-mounted into CDVI Atrium modules Insert into TC1/TCV2 backplane Fig. 6 Power Supply Metal Standoff Placement Power Supply or Sub-Assembly Metal Standoff Placement Sub-Assembly - 6 - Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI
Fig. 8 7.5 (190.5mm) TCV2 Dimensions 19.4 (492.76mm) 7.5 (190.5mm) 24.95 (633.73mm) 0.156 ( 3.96mm) 25.4 (645.16mm) 12.62 (320.55mm) 12.62 (320.55mm) 8.495 (215.77mm) 16.245 (412.62mm) 1.0 (25.4mm) 0.45 (11.43mm) 7.5 (190.5mm) 1.0 (25.4mm) 7.5 (190.5mm) 9.2 Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI - 7 -
Fig. 9 Trove2CV2 Enclosure Dimensions (H x W x D): 27.25 x 21.75 x 6.5 (692.15mm x 552.45mm x 165.1mm) 5.25 (133.35mm) 3.50 (88.9mm) 21.50 (546.1mm) 3.50 (88.9mm) 5.25 (133.35mm) 0.5625 (14.29mm) 2.415 (61.34mm) 1.77 (44.96mm) 0.685 (17.399mm) Knockouts 1.125 (28.32mm) 0.885 (22.479mm) 6.25 (158.75mm) 6.25 (158.75mm) 0.85 (21.59mm) 1.5 (38.1mm) 19.80 (502.92mm) 6.75 (171.45mm) G 27.00 (685.8mm) 8.25 (209.54mm) 8.00 (203.2mm) 0.85 (21.59mm) 1.00 (25.4mm) 5.25 (133.35mm) 7.00 (177.79mm) 5.25 (133.35mm) is not responsible for any typographical errors. Product specifications are subject to change without notice. 140 58th Street, Brooklyn New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail: info@altronix.com. Made in USA. IITrove1C1/Trove2CV2 - Rev. 05312016 F22P MEMBER - 8 - Trove1C1/TC1/Trove2CV2/TCV2 - /CDVI