USER MANUAL MH-B33 P l e a s e R e a d O v e r T h i s M a n u a l B e f o r e O p e r a t i n g T h e L i g h t F i x t u r e
ABLE OF CONTENTS TPART PRODUCT SPECIFICATIONS....--PRODUCT SPECIFICATIONS....--DIMENSIONS....3--PRODUCT FEATURES....4-- SAFETY WARNING...3. PART INSTALLATION...4..--MOUNTING...4..--SETTING UP....3--FUSE REPLACEMENT... PART 3 DISPLAY PANEL OPERATION... 3.--BASIC... 3.--MENU... 3.3--INTRO... 3.4--INVERT... 3.--RANGE... 3.--SPECIAL.... 3.--EDIT... 3.--EXTRA... 3.--CALIB.... 3.0--DEFAULT.... PART 4 USING DMX CONTROLLER...3. 4.--CHANNEL ASSIGNMENT... 3. PRODUCT SPECIFICATIONS. PRODUCT SPECIFICATIONS Electrical Voltage:AC00~40V,0/0Hz Rated Power:0W LED LED:3PC(3R+G+B) Cooling:Forced air convection Function Color mixing / Custom programs / Strobe / White balance / RGB calibration / Dim 4 / Fan speed Operation Control mode:master-slave/auto/custom/ Sound LCD display DMX Chs:CHS/ CHS Pan/Tilt Pan 40 Tilt 0 Pan/Tilt speed r-selectable Pan/Tilt ranges Size:400x30x0mm Weight:.kg PART APPENDIX.....--MAINTENANCE...
. DIMENSIONS. SAFETY WARNING 3. IMPORTANT 0 ALWAYS READ THE USER MANUAL BEFORE OPERATION. PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA. This product must be installed by a qualified professional. Always operate the equipment as described in the user manual. A minimum distance of 0.m must be maintained between the equipment and combustible surface. The product must always be placed in a well ventilated area. Always make sure that the equipment is installed securely. DO NOT stand close to the equipment and stare directly into the LED light source. Always disconnect the power supply before attempting and maintenance. Always make sure that the supporting structure is solid and can support the combined weight of the products. The earth wire must always be connected to the ground. Do not touch the power cables if your hands are wet.. 344 4. ATTENTION.3 PRODUCT FEATURES This product left the place of manufacture in perfect condition. In order to maintain this condition and for safe operation, the user must always follow the instructions and safety warnings described in this user manual. Avoid shaking or strong impacts to any part of the equipment. Make sure that all parts of the equipment are kept clean and free of dust. Always make sure that the power connections are connected correct and secure. If there is any malfunction of the equipment, contact your distributor immediately. When transferring the product, it is advisable to use the original packaging in which the product left the factory. Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent that their effectiveness is impaired. The lamp (LED) shall be changed if it has become damaged or thermally deformed. ITEM Head Side arm 3 Menu 4 Enter Down Up Switch Power input Fuse 0 DMX 3-PIN signal output DMX 3-PIN signal input 3 4 0 3
INSTALLATION. MOUNTING The LED fixture can be operated in any position at any angle. When mounted on a flat surface, the surface must be strong enough to support 0 times the weight of the fixture and stable so that the will be no damage caused to the fixture or surrounding people or objects because of movements of the fixture on the surface.. SETTING UP (STAND ALONE) The LED fixture can be used as a stand alone unit. The stand alone functions AUTO, AUTO and CUSTOM can be activated without the need to connect to any controller or connecting to any other equipment. Simply, access the <operation> menu from the DISPLAY and select the target program to activate. When the unit is mounted in a hanging position, the fixture is attached using the mounting brackets and a standard truss clamp or other clamping device. The mounting brackets supplied are mounted using quick-release locks allowing simple mounting or removal. Clamp Safety cable Quick-release lock.3 FUSE REPLACEMENT UPRIGHT HANGING Remove the safety cap by a screwdriver. Fetch the old fuse from safety cap. Install a new fuse. Install the safety cap. IMPORTANT SAFETY NOTE!! Always use a safety cable when installing this unit!! Be sure that the safety cable is connected to a solid load-bearing structure. Safety Cap Fuse 4
3 DISPLAY PANEL OPERATION 3. BASIC MENU UP Special Blackd Reset Power Color DMX System rmal High Off Rgbtow MENU Scroll through the main menu or exit from the current sub-menu ENTER Enter the currently selected menu or confirm the current function value DOWN Scroll 'DOWN' through the menu list or decrease the value of the current function UP Scroll 'UP' through the menu list or increase the value of the Current function 3. MENU MENU GENERAL Reset Fans Run Keylock Info Tilt.ReV Dimmer.Rev (00~) High rmal Low Auto DMX Auto Auto Sound Sound Custom Slave Test Basic Main 0 close Always Speed4 Speed3 Speed Speed Off Edition Invert Pan.Rev rmal rmal rmal PT.Range P/Begin (000~) P/End T/Begin T/End ENTER ADD.DMX Person LCD.Disp Dimspeed (000~) (000~) (000~) DOWN Extra 3.3 INTRO Dimmer Strobe Red Green Blue Pan Tilt Speed Time Password (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) Password Calib White MENU Fan Dmxerror Edit Step (000~) White RBG-W Default DMX System Save Black Default General Add.DMX Reset Fans (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (00~) High rmal Low Auto
Run Person LCD.DISP Keylock DMX Auto Auto Custom Slave Test Basic Main 0 close Bright Dimspeed Speed 4 Speed 3 Speed Speed Info Sound sound Speed 0 Edition 3.4 INVERT Invert Pan.Rev rmal Tilt.Rev Dimmer.Rev rmal rmal Invert Select Pan.Rev / Tilt.Rev / Dimmer.Rev to set rmal or Enter and set to run the new setting Address Enter Add.DMX to set the DMX Address, which is from (00-) Reset In order to rest custom modest to default, select Reset Fans Enter Fans to select the working mode of fan: High is for fast; rmal is for normal; Low is for slow ; Auto is for Auto Run Enter Run to select the operation mode: DMAX ; Auto ; Auto ; sound ; sound : Custom ; Test ; Slave PERSON Enter PERSON to select the DMX channel modes: Basic ; MAIN Display Enter Display to select the lighting time of the LCD display panel. Keylock Enter the Keylock mode to select whether the access password is on or off. DimSpeed Enter DimSpeed to select dimmer mode and dimmer speed. When DIMMER is set to Off, then RGBW and MASTER DIMMER are linear. The Dim //3/4 are speed modes of the non linear dimmer, SPEED is the faster, while SPEED4 is the slowest. The factory default setting is SPEED4. Enter Info to see the version of the software.
3. PT.RANGE 3. SPECIAL Range P/Begin (000~) Special P/End T/Begin T/End P/Begin Set pan start value 000~ P/End Set pan finish value 000~ T/Begin Set Tilt start value 000~ T/End Set Tilt finish value 000~ BlackD Reset Power Color Fan (000~) (000~) (000~) Enter and select to open the operation of X/Y angle Dmxerror DMX System rmal High Uc Rgbtow Off DMX System Save Black Edit 3. EXTRA Extra Time Password (000~) Enter the Edit mode to edit the custom programs by adjusting the value of Step, Pan, Tilt, Speed, Blue, Zoom, Green, Red, Dimmer, Strobe, Time Enter and select to run the steps user need. te: if user want to circulate the created steps, please set the last step s T ime as 0 For example, there are 3 steps, the setting should be like belowed: Step T ime = 4 = Step T ime = = Step 3 T ime = 0 = 0000 BlackD Enter BlackD to choose without delay or 3seconds delay Reset Enter Reset to choose DMX DMX control reset or System DMX cannot control reset Power Enter Power to choose the power as NORMAL or HIGH. Color COLOR is for activate/unactivate the color calibration functions. Fan C hoose DMX DMX to control fan or System DMX cannot control fan Dmxerror C hoose Save After loss of DMX Save, Black After loss of DMX black 3. EDIT Edit Step (000~) Pan (000~) Tilt (000~) Speed (000~) Red (000~) Green (000~) Blue (000~) Time (000~) Dimmer (000~) Strobe (000~) Zoom (000~) (000~) 0 When the user enter password and input the correct password, the 3. CALIB hidden menu Cablid, default will appear on display panel, and the user is able to reset the DEFAULT values of all functions. The default access code is UP + DOWN + UP + DOWN.. Calib 300K 3400K 400K 400K 00K (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~)
00K... (000~) (000~) (000~) 00K (000~) (000~) (000~) 4 USING A DMX CONTROLLER 00K (000~) (000~) (000~) 4. CHANNEL ASSIGNMENT te: This product have two DMX channel configuration: MAIN and BASIC. 000K (000~) (000~) (000~) MAIN Calib 3.0 DEFAULT Default 00K 0000K RBG-W Default Default (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) (000~) Enter the Calib to select white color of different color temperature. There are pre-programmed White colors plus RGB TO WHITE and can be edited by using Red, Green & Blue. This functions will reset all setting to the original factory setting CHANNEL VALUE FUNCTION 3 4 000~ DIMMER 000~00 00~ 000~00 00~00 0~030 03~00 0~00 0~00 0~0 ~30 3~0 ~0 ~00 0~0 0~0 ~ ~0 ~ ~30 3~3 3~40 4~4 4~0 ~ 000~ STROBE NO function ~0Hz COLOR/WHITE MACRO NO FUCNTION FULL POWER 00% / UP / 0% DOWN / 00% / 0% 0% / 00% / UP 0% / DOWN / 00% UP / 0% / 00% 00% / 0% / DOWN 00% / UP / UP DOWN / DOWN / 00% 00% / 00% / 00% /WHITE 00% WHITE:300K WHITE:3400K WHITE3:400K WHITE4:400K WHITE:00K WHITE:00K WHITE:00K WHITE:00K WHITE:000K WHITE0:00K WHITE:0000K 000~ 000~ 000~ PAN Clockwise rotate 0~ 40 3
CHANNEL VALUE FUNCTION BASIC 000~ PAN FINE Fine control of pan movement 0~3 CHANNEL VALUE FUNCTION 000~ TILT Anti-clockwise rotate 0~0 000~ DIMMER 0 000~ TILT FINE Fine control of tilt movement 0~3 000~00 00~ STROBE NO function ~0Hz 000~ 000~0 00~03 040~0 00~0 00~0 00~ 0~3 40~4 0~ 0~ 0~ 0~ 00~ 0~ PAN/TILT SPEED From fast to slow CONTROL PAN/TILT BLACK ACTIVATED PAN/TILT BLACK DEACTIVATED FAN AUTO FAN SLOW FAN NORMAL FAN FAST AUTO (ACTIVATED AFTER 3 SECS) AUTO (ACTIVATED AFTER 3 SECS) TEST (ACTIVATED AFTER 3 SECS) CUSTOM (ACTIVATED AFTER 3 SECS) RESET (ACTIVATED AFTER 3 SECS) 3 000~00 00~00 0~030 03~00 0~00 0~00 0~0 ~30 3~0 ~0 ~00 0~0 0~0 ~ ~0 ~ ~30 3~3 3~40 4~4 4~0 ~ COLOR/WHITE MACRO NO FUCNTION FULL POWER 00% / UP / 0% DOWN / 00% / 0% 0% / 00% / UP 0% / DOWN / 00% UP / 0% / 00% 00% / 0% / DOWN 00% / UP / UP DOWN / DOWN / 00% 00% / 00% / 00% /WHITE 00% WHITE:300K WHITE:3400K WHITE3:400K WHITE4:400K WHITE:00K WHITE:00K WHITE:00K WHITE:00K WHITE:000K WHITE0:00K WHITE:0000K 4 000~ 000~ 000~ 000~ PAN Clockwise rotate 0~ 40 4
CHANNEL VALUE 000~ FUNCTION TILT Anti-clockwise rotate 0~0 APPENDIX. MAINTENANCE 000~0 00~03 040~0 00~0 00~0 00~ 0~3 40~4 0~ 0~ 0~ 0~ 00~ 0~ CONTROL PAN/TILT BLACK ACTIVATED PAN/TILT BLACK DEACTIVATED FAN AUTO FAN SLOW FAN NORMAL FAN FAST AUTO (ACTIVATED AFTER 3 SECS) AUTO (ACTIVATED AFTER 3 SECS) TEST (ACTIVATED AFTER 3 SECS) CUSTOM (ACTIVATED AFTER 3 SECS) RESET (ACTIVATED AFTER 3 SECS) ITEM ITEM ITEM Head front cover Lead aperture 3 4 Arm board Base cover 3 lens IEC power socket 4 Capture lens plate DMX connection board Base cover 30 0 LED support Fan plate Fan Head back cover Motor driver PCB Motor Optical wheel Y-small gear 0 3 4 Fan Pan belt Power supply Display PCB Display support U-frame Y-motor support 3 3 Y-large gear Pan belt Driver PCB Head structure LED PCB Capture lens Capture lens plate Capture lens plate