Blue ID Power injection module Legend A B LED for status of module LED for system power LED for status of module The LED shows the status of the module. The LED is on continuously when the module is working correctly. If not, and in special circumstances, the LED flashes. LED for system power An LED indicates the status of the system power. The LED is on if the power supply is working correctly. A Blue ID Power injection module is used to power a new, fused power supply segment. Characteristics voltage monitoring transferring communications signals 24 V system power supply monitoring wiring uses spring terminals New power supply segment The I/O modules in Blue ID are powered by the system power supply (24 VDC). This system power is connected via the controller and then distributed via the base of the I/O modules. If the I/O modules demand more power than can be supplied via the controller, a Blue ID Power injection module must be used. TC Engineer calculates this for you. Clear indication On the PI module the system power present (A) is interrupted and re-established (B). This creates a new power supply segment (C). To do this both A and B should be present therefore. The internal communication signals (D) are transferred as normal. This module may not be removed or installed while the power is connected. 1
Connections Legend A B C + - FE release mechanism for module cover, fuse can be accessed by removing cover glass fuse LED for system power +24 VDC (SP) 0 (SG) functional earth 2
Specifications PI module General Article description Article number Dimensions (XYZ) Weight Power consumption MTBF¹ Installation Material Connector type for power supply Permitted core cross section area Blue ID Power injection module 5050010 161.5 x 40 x 58 mm (6.36 x 1.57 x 2.28 inch) 150 grams 2.3 W 4,380,000 hours clicks onto DIN rail mixture of polycarbonate and ABS terminal block solid: 0.2 mm² 4 mm² flexible: 2.5 mm² flexible with ferrule connector: 0.25 mm² 1.5 mm² Indication green LED for status of module green LED for system power ¹ The MTBF is calculated according to the Telcordia SR-332 standard Issue 2 under the following conditions: - ambient temperature: 35 50 C - supply voltage: 24 VDC - time in operation per day: 24 hours - reliability level: 60 % 3
Electrical Input voltage Maximum input current Minimum switch off voltage Maximum switch off voltage Maximum voltage between: FE and SP FE and SG Capacity between: FE and SP FE and SG Resistance between FE and SG Protection Glass fuse Accuracy of internal temperature measurement Power supply The system power supply must comply with the following requirements. 21.6 VDC - 26.4 VDC (24 VDC ± 10 %) 2.5 A 21.1 VDC 26.9 VDC ± 43 V peak 1nF nominal 1 MΩ nominal input is protected against incorrect connection of ± 30 VDC and 30 VAC 2.5 AT ± 2 C Requirements output voltage: 21.6 26.4 VDC double insulation between input and output "limited-energy circuit" in accordance with IEC 61010-1 (maximum output current in normal operation or "single fault condition": 8 A) or maximum 4 AT external fuse between the power supply and the power supply input General specifications for controller, modules and bases Housing IP code Flammability class Recycle code Colour IP30 (NEN-EN-IEC 60529) FV-0 7 release surfaces of module and DIN rail release: blue (RAL5013) other parts: white (RAL9003) Mounting and connection Installation in control cabinet, accessible to authorised personnel only open device, to be used in an environment with a permitted pollution factor of 2 can be clicked onto mounting plate on horizontally or vertically positioned DIN rail Maximum width of I/O modules, bus extension modules and controller Environment Permitted temperature inside control cabinet during normal operation Permitted temperature inside control cabinet during transport and storage Permitted relative ambient humidity Shock and vibration resistance Installation category Permitted ambient pollution Note: The controller, SC module and SN module may only be mounted horizontally. 20 m 0 50 ºC 0 70 ºC 10 % - 95 % (non-condensing) IEC61131-2 II pollution degree 2 Legislation and standards Canada / USA CSA/UL approved, in compliance with: UL 61010-1:2004 (measurement and control equipment) CSA C22.2 No 61010-1-04 (measurement and control equipment) ICES-003 Issue 4 Class B 4
Legislation and standards Europe CE mark, in compliance with: Low voltage directive 2006/95/CE EMC directive 2004/108/EC RoHS directive 2011/65/EU in compliance with harmonised standard IEC 61010-1:2010 (3rd Edition) in compliance with WEEE Directive 2002/96/EC International The Blue ID S10 Controller is BTL registered at BACnet International. The Blue ID S10 Controller is BACnet certified in accordance with ISO 16484-5/6. Priva is a member of the BACnet Interest Group Europe. 5
Europe Office: UK Office: Canada Office: Your Priva partner: Priva Zijlweg 3 P.O. Box 18 2678 ZG De Lier The Netherlands T +31 174 522 600 F +31 174 522 700 www.priva.nl sales.building@priva.nl Priva Zijlweg 3 PO Box 18 2678 ZG De Lier The Netherlands T +44 (0)1923 813 480 F +44 (0)1923 813 499 www.priva.co.uk sales@priva.co.uk Priva North America Inc. 3468 South Service Road Vineland Station Ontario LOR 2E0 Canada T +1(905) 562-7351 F +1(905) 562-7717 www.priva.ca contact.priva@priva.ca 5201110_01.004_07-2013