Analog Key features of the RE series include: 0 time ranges and 0 timing functions ime delays up to 600 hours Space-saving package High repeat accuracy of ± 0.% ON and timing LED indicators Standard 8- or -pin and -blade termination form C delayed output contacts 0A Rating Cert. No. E9950933336 (EMC, RE) cert. No. BL9608333355 (LVD, RE) UL Listed File No. E66043 eneral Specifications System Solid state CMOS Circuit ype Multi-Mode ime Range 0.sec to 600 hours Pollution Degree (IE60664-) Over voltage category III (IE60664-) AF0 00-40V AC(50/60Hz) Rated al AD4 4V AC(50/60Hz)/4V DC Voltage D V DC AF0 85-64V AC(50/60Hz) Voltage olerance AD4 0.4-6.4V AC(50/60Hz)/.6-6.4V DC D 0.8-3.V DC Input off Voltage Rated Voltage x0% minimum Ambient Operating emperature -0 to +65ºC (without freezing) Ambient Storage and ransport emperature -30 to +75ºC (without freezing) Relative Humidity 35 to 85%RH (without condensation) Atmospheric Pressure 80kPa to 0kPa (Operating), 70kPa to 0kPa (ransport) Reset ime 00msec maximum Repeat Error ±0.%, ±0msec* Voltage Error ±0.%, ±0msec* emperature Error ±0.5%, ±0msec* Setting Error ±0% maximum Insulation Resistance 00MΩ minimum (500V DC) Between power and output terminals: 000V AC, minute Dielectric Strength Between contacts of different poles: 000V AC, minute Between contacts of the same pole:000v AC, minute Vibration Resistance 0 to 55Hz amplitude 0.5mm hours in each of 3 axes Operating extremes: 98m/sec (0) Shock Resistance Damage limits: 490m/sec (50) 3 times in each of 3 axes Degree of Protection IP40 (enclosure) (IEC6059) YPE RE-P, -B RE-P, -B Consumption (Approx.) AF0 0V AC/60Hz 6.5VA 6.6VA 40V AC/60Hz.6VA.6VA 4V AC 60Hz/DC 3.4VA/.7W 3.5VA/.7W D.6W.6W Free Mounting Position RE-P, P 40Hx 36W x 77.9D mm Dimensions RE-B, B 40Hx 36W x 74.9D mm RE-P RE-P RE-B, -B Weight (Approx.) 87g 89g 85g *For the value of the error against a preset time, whichever the largest. Ratings Form C, DPD Configuration (Delay output) Allowable Voltage / 40V AC, 30V DC / 0A Allowable Current Maximum Permissible 800 cycles per hour Operating Frequency Rated Load Life Resistive Inductive Horse Rating Electrical Mechanical 0A 40V AC, 30V DC 7A 40V AC, 30V DC /6 HP 0V AC, /3 HP 40V AC 500,000 op. minimum (Resistive) 50,000,000 op. minimum RE able of Contents Specifications -8 Part Number uide -9 Part Number List -9 RE iming Diagrams -0 RE Accessories - Instructions: Setting imer - RE Dimensions -3 eneral iming Diagrams -4-8 www.idec.com USA: (800) 6-IDEC or (408) 747-0550, Canada: (888) 37-IDEC
Part Numbering uide RE series part numbers are composed of 4 part number codes. When ordering a RE series part, select one code from each category. Example: RE-PAF0 RE P AF0 ➀ Series ➁ erminal Style ➂ Function roup ➃ Input Voltage Part Numbers: Description Part Number Code Remarks ➀ Series RE series RE For internal circuits, see next page. ➁ erminal Style ➂ Function roup ➃ Input Voltage Pin Blade ON-delay, interval, cycle OFF, cycle ON ON-delay, cycle OFF, cycle ON, signal ON/OFF delay, OFF-delay, one-shot 00 to 40V AC(50/60Hz) AF0 4V AC(50/60Hz)/4V DC AD4 V DC D P B Select one only. Each function group has different timing functions. See page -4. Part Number List Part Numbers riggered Input riggered Voltage 8-Pin Blade -Pin Blade V DC RE-PD RE-BD RE-PD RE-BD 4V AC/DC RE-PAD4 RE-BAD4 RE-PAD4 RE-BAD4 00-40V AC RE-PAF0 RE-BAF0 RE-PAF0 RE-BAF0 ime Range able ime Range Determined by ime Range Selector & Dial Selector Dial 0-0 - 3 0-0 0-30 0-60 Second 0. sec - sec 0. sec - 3 sec 0. sec - 0 sec 0.6 sec - 30 sec. sec - 60 sec Range Minute. sec - min 3.6 sec - 3 min sec - 0 min 36 sec - 30 min. min - 60 min Hour. min - hr 3.6 min - 3 hr min - 0 hr 36 min - 30 hr. hr - 60 hr 0 Hours min - 0 hr 36 min - 30 hr hr - 00 hr 6 hr - 300 hr hr - 600 hr www.idec.com USA: (800) 6-IDEC or (408) 747-0550, Canada: (888) 37-IDEC -9
iming Diagrams RE-P 3 4 5 8 6 7 external control RE-P 3 start 4 8 9 0 RE-B 7 8 A 3 5 6 9 B external control RE-B A start 3 4 5 6 7 8 RE-P, -B A: ON-Delay (power start) B: Interval (power start) Set timer for desired delay, apply power to coil. s transfer after preset time Set timer for desired delay, apply power to coil. s transfer immediately, and has elapsed, and remain in transferred position until timer is reset. Reset occurs return to original position after preset time has elapsed. Reset occurs with removal with removal of power. of power. ()-7 ()A-B ()-4,5-8 ()-7,3-9 (NC) ()-3,6-8 ()4-7,6-9 (NO) 9 B ()-7 ()A-B ()-4,5-8 ()-7,3-9 (NC) ()-3,6-8 ()4-7,6-9 (NO). RE-P: Do not apply voltage to terminals #5, #6 & #7.. RE-B, -B: Do not apply voltage to terminals #, #5 & #8. 3. IDEC sockets are as follows: RE-P: SRP-06* pin type socket, RE-P: SR3P-05* pin type socket, RE-B, -B: SR3B-05* blade type socket, (*-may be followed by suffix letter A,B,C or U). C: Cycle (power start, OFF first) Set timer for desired delay, apply power to coil. First transfer of contacts occurs after preset delay has elapsed, after the next elapse of preset delay contacts return to original position. he timer now cycles between on and off as long as power is applied (duty ratio :). ()-7 ()A-B ()-4,5-8 ()-7,3-9 (NC) ()-3,6-8 ()4-7,6-9 (NO) A: ON-Delay (signal start) When a preset time has elapsed after the start input turned on while power is on, the NO output contact goes on. (A)-0 (B)-5 (A)-4,8- (B)-7,3-9 (NC) (A)-3,9- D: Cycle 3 (power start, ON first) Functions in same manner as Mode C, with the exception that first transfer of contacts occurs as soon as power is applied. he ratio is :. ime On = ime Off ()-7 ()A-B ()-4,5-8 ()-7,3-9 (NC) ()-3,6-8 ()4-7,6-9 (NO) RE-P, -B B: Cycle (signal start, OFF first) When the start input turns on while power is on, the output oscillates at a preset cycle (duty ratio :), starting while the NO contact off. (A)-0 (B)-5 (A)-4,8- (B)-7,3-9 (NC) (A)-3,9- C: Cycle 4 (signal start, ON first) When the start input turns on while power is on, the NO contact goes on. he output oscillates at a preset cycle (duty ratio :). (A)-0 (B)-5 (A)-4,8- (B)-7,3-9 (NC) (A)-3,9- E: Signal OFF-Delay When power is turned on while the start input is on, the NO output contact goes on. When a preset time has elapsed after the start input turned off, the NO output contact goes off. (A)-0 (B)-5 (A)-4,8- (B)-7,3-9 (NC) (A)-3,9- a F: One-Shot (signal start) When the start input turns on while power is on, the NO output contact goes on. When a preset time has elapsed, the NO output contact goes off. (A)-0 (B)-5 (A)-4,8- (B)-7,3-9 (NC) (A)-3,9- D: Signal ON/OFF-Delay When the start input turns on while power is on, the NO output contact goes on. When a preset time has elapsed while the start input remains on, the output contact goes off. When the start input turns off, the NO contact goes on again. When a preset time has elapsed after the start input turned off, the NO contact goes off. (A)-0 (B)-5 (A)-4,8- (B)-7,3-9 (NC) (A)-3,9- a a a a a a Note : =, a=shorter than set time, (): RE-P, (): RE-B, (A): RE-P, (B): RE-B -0 www.idec.com USA: (800) 6-IDEC or (408) 747-0550, Canada: (888) 37-IDEC
emperature Derating Curves Mounting A Allowable Current 0A 7A Mounting B Allowable Current Mounting A Mounting B Derating Curve Derating Curve 50ºC 65ºC 50ºC 65ºC Ambient emperature Ambient emperature 7A 5A Instructions ypes RE-PAF0 Connection type P: Pin B: Blade Mode : No Control Signal A: ON-Delay B: Interval C: Cycle D: Cycle 3 Installation of Hold-Down Springs DIN Rail Mount Socket Insert the springs into the outer slots with the projections facing inside. Voltage AF0: 00 to 40V AC(50/60Hz) AD4: 4V AC(50/60Hz)/4V DC D: V DC : Control Signal A: ON-Delay B: Cycle C: Cycle 4 D: Signal ON/OFF-Delay E: Signal OFF-Delay F: One-Shot Insert the springs into the slots. Switch Settings 3 Mode Selector Scale Selector 3 ime Range Selector. urn the selectors securely using a flat screwdriver 4mm wide (maximum). Note that incorrect setting may cause malfunction. Do not turn the selectors beyond their limits.. Since changing the setting during timer operation may cause malfunction, turn power off before changing. Socket SRP-06 Hold-down Spring (sold separately) SFA-0 (use two springs) Socket SR3P-05 Hold-down Spring (sold separately) SFA-03 (use two springs) Safety Precautions Special expertise is required to use Electronic. All Electronic are manufactured under IDEC's rigorous quality control system, but users must add a backup or fail safe provision to the control system when using the Electronic imer in applications where heavy damage or personal injury may occur should the Electronic imer fail. Install the Electronic imer according to instructions described in this catalog. Make sure that the operating conditions are as described in the specifications. If you are uncertain about the specifications, contact IDEC in advance. In these directions, safety precautions are categorized in order of importance under Warning and Caution. Warnings Warning notices are used to emphasize that improper operation may cause severe personal injury or death. urn power off to the Electronic timer before starting installation, removal, wiring, maintenance, and inspection on the Electronic imer. Failure to turn power off may cause electrical shocks or fire hazard. Do not use the Electronic imer for an emergency stop circuit or interlocking circuit. If the Electronic imer should fail, a machine malfunction, breakdown, or accident may occur. Caution Caution notices are used where inattention might cause personal injury or damage to equipment. he Electronic imer is designed for installation in equipment. Do not install the Electronic imer outside equipment. Install the Electronic imer in environments described in the specifications. If the Electronic imer is used in places where it will be subjected to high-temperature, high-humidity, condensation, corrosive gases, excessive vibrations, or excessive shocks, then electrical shocks, fire hazard, or malfunction could result. Use an IEC607-approved fuse and circuit breaker on the power and output line outside the Electronic imer. Do not disassemble, repair, or modify the Electronic imer. When disposing of the Electronic imer, do so as industrial waste. www.idec.com USA: (800) 6-IDEC or (408) 747-0550, Canada: (888) 37-IDEC -
DIN Rail Mounting Accessories Part Numbers: DIN Rail/Surface Mount Sockets and Hold-Down Springs DIN Rail Mount Socket Applicable Hold-Down Springs Style Appearance Use with Part No. Appearance Part No. -Pin Screw erminal (dual tier) RE-P SR3P-05 SFA-03 -Pin FingerSafe Socket RE-P SR3P-05C 8-Pin Screw erminal RE-P SRP-06 SFA-0 -Blade Screw erminal RE-B RE-B SR3B-05 DIN Mounting Rail Length 000mm BNDN000 Panel Mounting Accessories Part Numbers: Flush Panel Mount Adapter and Sockets that use an Adapter Accessory Description Appearance Use with Part No. Panel Mount Adapter Adaptor for flush panel mounting RE timers All RE timers RB-0 8-pin screw terminal (Shown: RE-P SR6P-M08 SR6P-M08 Wiring Socket Adapter) -pin screw terminal RE-P SR6P-M Sockets for use with Panel Mount Adapter 8-pin solder terminal RE-P SR6P-S08 -pin solder terminal RE-P SR6P-S No hold down clips are available for flush panel mounting applications. - www.idec.com USA: (800) 6-IDEC or (408) 747-0550, Canada: (888) 37-IDEC
Dimensions 36.0 3.7 77.9 3.0 40.0 RE-P (8 pin) erminal Style RE-P ( pin)erminal Style 7.3 RE-B/RE-B ( blade) erminal Style Panel Mount Adapter RE imer, 8-Pin and -Pin with SR6P-S08 or SR6P-S 98 maximum Panel hickness 0.8 to 5mm 48.7 4.5 48 6. Back Wiring Socket RE imer, 8-Pin with SR6P-M08 Panel hickness 0.8 to 5mm 8-M3.5 erminal Screw 44.6 3.5 max. 5.6 min. 3 4 5 6 ø3.6 min. 44.6 30.4 8 7 6.9 max. 7 80.5 9.8 3 RE imer, -Pin with SR6P-M -M3.5 eminal Screws 45 6.7 7 6 5 3.5 max. 5.8 min. ø3.6 min. 45 34 6.9 max. 4 3 8 9 0 30.5 7 9 8.5 4 www.idec.com USA: (800) 6-IDEC or (408) 747-0550, Canada: (888) 37-IDEC -3