Chapter1: Overview 1.1 Product Description Thanks for choosing the 2LAN+1POTS+WiFi Home Gateway Unit. The terminal devices are designed for fulfilling FTTH and triple play service demand of fixed network operators or cable operators. These boxes are based on the mature GPON and Gigabit EPON technology, which have high ratio of performance to price, and the technology of 802.11n WiFi (2T2R), Layer 2/3, and high quality VoIP as well. They are highly reliable and easy to maintain, with guaranteed QoS for different service. And they are fully compliant with GPON and EPON technical regulations such as ITU-T G.984.x, IEEE802.3ah and technical requirement of EPON Equipment from Telecom. Dual mode HGU can detect and exchange PON mode automatically. 1.2Application Chart Figure 1 2LAN+1POTS+WiFi Dual Mode HGU Figure 2 Application Chart
1.3Technical parameters Technical items PON interface Wavelength Optical interface LAN interface POTS interface Indicators DC power supply Power consumption Operating condition Storing condition Dimension Net weight 2LAN+1POTS+WiFi Dual Mode HGU 1 GPON/EPON interface, SC single-mode/single-fiber. GPON: uplink 1.25Gbps, downlink 2.5Gbps; EPON: symmetric 1.25Gbps Tx 1310nm, Rx 1490nm SC/PC 2*10/100Mbps or 1*10/100Mbps and 1*10/100/1000Mbps Auto adaptive Ethernet interfaces, Full/Half Duplex, RJ45 connectors 1 FXS, RJ11 connectors 8 indicators +12V /1A, external AC-DC power adaptor 6W Operating temp: -5 ~ +55 Operating humidity: 10~90% (non-condensing) Storing temp: -30 ~ +60 Storing humidity:10~90%(non-condensing) 185mm*120mm*34mm(length*width*height) 0.24kg Table 1 Technical parameters 1.4Equipment List Contents Quantity Contents Quantity HGU 1 pcs Power adapter 1 pcs User manual 1 pcs Table 2 Equipment List
2.1Installation Requirements Chapter2: Installation Installation Environment Requirements HGU equipment must be installed in the interior, and to ensure the following conditions: Confirmation at the HGU installation at sufficient space to facilitate cooling machine. HGU suitable operating temperature of -5 ~ 55,humidity10% to 90%. Device workplace should avoid radio transmitters,radar stations, and high-frequency interference from power equipment. Equipment Installation 1. installed on the desktop Place the machine on a clean bench, this installation is relatively simple, you can observe the following operation: Ensure the smoothworkbench. Around the device enough space for heat dissipation. 2. mounted on the wall Observation HGU equipment chassis two cruciform recess, in accordance with the position ofthe groove, installed two screwsin the wall. The original selected two mounting screws gently snap into recesses aligned. Slowly let go,so that the device under the supportof the screw hanging on the wall. 2.2Panel Figure 3 Panel lights LED Mark Status Description Power POWER On The device is powered up. The device is powered down. On The device is registered to PON system. Registration PON Device is not registered to PON system. Blink Deviceis registering. Optical signal LOS Blink Device does not receive optical signals.
Device has receivedoptical signal. Ethernet LAN1 LAN2 On Blink Port is connectedproperly. Portconnection exceptionor not connected. Port issending or/and receiving data. Pots PHONE On Device has registered to the soft-switch, but without ongoing data transmission Device is power off or not registered to the soft-switch Blink The port is with ongoing data transmission On WPS client is connected. ( LED turn off after 5 minutes of successful connection) Pair Pair Does not use WPS or WPS client is connected.( LED turn off after 5 minutes of successful connection) Blink WPS client is connecting. On WiFi turned on. Wireless WiFi Device is power off or WiFi turned off. Blink WiFi turn on and with ongoing data transmission. Table3 Panel lights Figure 4 Back panel Name PON FXS1 LAN1/2 Pair WiFi Function Connect PON port with internet by SC type, single mode optical fiber cable. Connect the telephone with FXS port by telephone wire. If you only have one telephone, you should use FXS1 port. Connect PC with HGU Ethernet port by RJ-45 Cat5 cable. Press down WiFi pair button to begin pairing. Press down WiFi turn on/off button to enable/disable WiFi function.
RST PWR 1. Press RST button over 10 seconds, onu can restore factory defaults and reboot. 2. Press RST button quickly, onu reboot. Connect with power adapter. Table 4 Back panel Chapter3: Web Management 2LAN+1POTS+WiFi dual mode HGU provides simple Web management function. 3.1Default configuration The following is the default device configuration information. Local (LAN access) Username: user, Password: user LAN port management IP address: 192.168.1.1/24 3.2Basic Configuration Figure 5 web Login Web logindefault username: user password: user
Figure 6 Status WAN Info display the status of all WAN connections and the network information. Figure 7 LAN setting IP Address and Subnet Mask:LAN port IP address and mask. DHCP option:enable or disable DHCP server and configure IP address pool, DNS, etc. Note: DHCP server changes take effect afterthe device is restarted.
Figure 8 WLAN settings WLAN Basic displays the current configuration information. Modify these parameters to change WiFi basic features. Security is used to set up encryption for SSID Figure 9 User ManageSettings
Figure 6User ManageSettings User Manage just for Access Control. Modify password of user. User Manage modify the password of ordinary user account of user. 1. After power all the lights are lit? 1) Power connection errors; 2) Power is not normal. 1) Check that the power cable is connected; 2) The rear panel of the power supply is turned on. Chapter4: Troubleshooting 2. GE / FE led does not light? 1) Network cable is damaged or loose connection; 2) Cable type error; 3) Long lines outside the allowable range. 1) Replace the network cable, and pay attention to the standard Ethernet cable must be parallel or crossing lines. 3. After working for some time to stop working? 1) Power supply is not working properly;
2) The equipment from overheating. 1) Check if there is contact with abnormal voltage is too high or too low; 2) Check the ambient conditions, vents are normal ventilation. 4. LOS led flashes? 1) Fiber failure; 2) Central office equipment failure. 1) Inspect fiber is connected properly, is connected to the correct connector, optical power is normal; 2) Contact your operator. 5. PON led flashes? 1) Fiber optic connector is loose; 2) Central office equipment failure; 3) Fiber optic connectors are dust. 1) Inspect fiber is connected properly; 2) Cotton ball with alcohol swabbing fiber optic connectors; 3) Contact your operator.