P4P800-X Motherboard
2 C1718
3
4
5
6
1 2 2 3 Jumper Mode Jumper Free (Default) 7
8
9
10
1-1
1-2
1-3
SB_PWR P4P800-X P4P800-X Onboard LED ON Standby Power OFF Powered Off 1-4
20.8cm (8.2in) CPU_FAN ATX12V SPDIF1 COM1 USB12 USBPW34 USBPW12 Socket 478 USB2.0 FP_AUDIO CD AUX CLRTC CHASSIS SPDIF_OUT SEC_IDE 30.5cm (12.0in) P4P800-X SATA2 SATA1 SB_PWR COM2 GAME CHA_FAN USBPW56 USBPW78 USB56 USB78 PANEL 1-5
1-6
P4P800-X P4P800-X CPU Socket 478 Gold Arrow 1-7
90-100 1-8
80 Pins P4P800-X 104 Pins P4P800-X 184-Pin DDR DIMM sockets DIMM_A1 DIMM_A2 DIMM_B1 DIMM_B2 1-9
1-10
1-11
1-12
A B C D E F G H 1-13
P4P800-X Keyed for 1.5v P4P800-X Accelerated Graphics Port (AGP) 1-14
CLRTC P4P800-X P4P800-X Clear RTC RAM 2 1 Normal (Default) 3 2 Clear CMOS 1-15
P4P800-X 2 1 USBPW12 USBPW34 3 2 +5V +5VSB (Default) USBPW56 USBPW78 1 2 2 3 P4P800-X USB device wake up +5V (Default) +5VSB 1-16
1 2 3 4 5 6 11 10 9 8 7 1-17
NOTE: P4P800-X P4P800-X IDE connectors PRI_IDE PIN 1 SEC_IDE PIN 1 FLOPPY P4P800-X PIN 1 P4P800-X Floppy disk drive connector Orient the red markings on the floppy ribbon cable to PIN 1. 1-18
SATA2 GND RSATA_RXP2 RSATA_RXN2 GND RSATA_TXN2 RSATA_TXP2 GND SATA1 P4P800-X GND RSATA_RXP1 RSATA_RXN1 GND RSATA_TXN1 RSATA_TXP1 GND P4P800-X SATA connectors 1-19
1-20
P4P800-X ATX12V +12V DC GND +12V DC GND Pin 1 +12.0VDC +5VSB PWR_OK COM +5.0VDC COM +5.0VDC COM +3.3VDC +3.3VDC ATXPWR +5.0VDC +5.0VDC -5.0VDC COM COM COM PS_ON# COM -12.0VDC +3.3VDC P4P800-X ATX power connectors P4P800-X CD (Black) AUX (White) Right Audio Channel Ground Ground Left Audio Channel Right Audio Channel Ground Ground Left Audio Channel P4P800-X Internal audio connectors 1-21
CPU_FAN Rotation +12V GND CHA_FAN P4P800-X GND +12V Rotation P4P800-X Fan connectors USB+5V USB_P6- USB_P6+ GND NC USB+5V USB_P8- USB_P8+ GND NC P4P800-X P4P800-X USB 2.0 connectors USB56 1 USB+5V USB_P5- USB_P5+ GND USB78 1 USB+5V USB_P7- USB_P7+ GND 1-22
P4P800-X FP_AUDIO MIC2 AGND MICPWR +5VA Line out_r BLINE_OUT_R NC Line out_l BLINE_OUT_L P4P800-X Front panel audio connector CHASSIS GND Chassis Signal (Default) P4P800-X +5VSB_MB P4P800-X Chassis intrusion connector 1-23
P4P800-X P4P800-X Game connector GAME +5V +5V J1B1 J2B1 J1CX J2CX GND MIDI_OUT GND J2CY J1CY J2B2 J1B2 MIDI_IN +5V GND SPDIFOUT SPDIF_OUT P4P800-X +5V P4P800-X Digital audio connector 1-24
COM2 PIN 1 P4P800-X P4P800-X Serial port connector PANEL Power LED +5 V PLED Speaker Connector +5V Ground Ground Speaker P4P800-X P4P800-X System panel connector HD_LED+ HD_LED- ExtSMI# Ground PWRBIN Ground Reset Ground Reset SW IDELED ATX Power SMI Lead Switch* * Requires an ATX power supply. 1-25
1-26
2-1
2-2
A:\>afudos /ip4p800x.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file... done Erasing flash... done Writing flash... 0x0008CC00 (9%) 2-3
A:\>afudos /ip4p800x.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file... done Erasing flash... done Writing flash... 0x0008CC00 (9%) Verifying flash.. done A:\> A:\>afudos /omybios03.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash... 0x0008CC00 (9%) 2-4
A:\>afudos /omybios03.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash... done A:\> User recovery requested. Starting BIOS recovery... Checking for floppy... 2-5
User recovery requested. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file P4P800X.ROM. Completed. Start flashing... Flashed successfully. Rebooting. Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... 2-6
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file P4P800X.ROM. Completed. Start flashing... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM... CD-ROM found. Reading file P4P800X.ROM. Completed. Start flashing... 2-7
2-8
System Time [11:10:19] System Date [Thu 03/27/2003] Legacy Diskette A [1.44M, 3.5 in] Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Select Screen Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit 2-9
System Time [11:10:19] System Date [Thu 03/27/2003] Legacy Diskette A [1.44M, 3.5 in] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] Use [+] or [-] to configure system time. Select Screen Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit Advanced Chipset settings WARNING: Setting wrong values in the sections below may cause system to malfunction. Configure DRAM Timing by SPD Memory Acceleration Mode DRAM Idle Timer DRAm Refresh Rate [Enabled] [Auto] [Auto] [Auto] Graphic Adapter Priority [AGP/PCI] Graphics Aperture Size [ 64 MB] Spread Spectrum [Enabled] ICH Delayed Transaction [Enabled] MPS Revision [1.4] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 2-10
System Time [11:10:19] System Date [Thu 03/27/2003] Legacy Diskette A [1.44M, 3.5 in] Primary IDE Master Primary IDE Slave Secondary IDE Master Secondary IDE Slave Third IDE Master Fourth IDE Master IDE Configuration System Information :[ST320413A] :[ASUS CD-S340] :[Not Detected] :[Not Detected] :[Not Detected] :[Not Detected] Use [ENTER], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time. Select Screen Select Item +- Change Field Tab Select Field F1 General Help F10 Save and Exit ESC Exit 2-11
Primary IDE Master Device : Hard Disk Vendor : ST320413A Size : 20.0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode : Supported Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported Type LBA/Large Mode Block (Multi-sector Transfer) PIO Mode DMA Mode Smart Monitoring 32Bit Data Transfer [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Disabled] Select the type of device connected to the system. Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 2-12
IDE Configuration Onboard PCI IDE Operate Mode [Enhanced Mode] Enhanced Mode Support On [S-ATA] IDE Detect Time Out (Sec) [35] 2-13
AMIBIOS Version : 08.00.09 Build Date : 04/05/04 Processor Type : Intel(R) Pentium(R) 4 Family CPU 1.73G Speed : 1733MHz Count : 1 System Memory Size : 512MB 2-14
JumperFree Configuration CPU Configuration Chipset Onboard Devices Configuration PCIPnP USB Configuration Adjust system frequency/voltage Configure System Frequency/Voltage AI Overclock Tuner CPU VCore Voltage [Standard] [Auto] 2-15
Configure System Frequency/Voltage AI Overclock Tuner [Manual] CPU Frequency [133] DRAM Frequency [Auto] AGP/PCI Frequency [Auto] CPU VCore Voltage DDR Reference Voltage [Auto] [Auto] 2-16
Configure advanced CPU settings Manufacturer: Intel Brand String: Intel(R) Pentium(R) 4 Family CPU 2.40G Frequency : 2399 MHz FSB Speed : 533 MHz This should be enabled inorder to boot legacy OSes that cannot support CPUs with extended CPUID functions. Cache L1 Cache L2 Cache L3 : 8 KB : 512 KB : 0 KB Ratio Status: Locked Ratio Actual Value: 18 Max CPUID Value Limit: [Disabled] 2-17
Advanced Chipset settings WARNING: Setting wrong values in the sections below may cause system to malfunction. Configure DRAM Timing by SPD [Enabled] Memory Acceleration Mode [Auto] DRAM Idle Timer [Auto] DRAm Refresh Rate [Auto] Graphic Adapter Priority [AGP/PCI] Graphics Aperture Size [ 64 MB] Spread Spectrum [Enabled] ICH Delayed Transaction [Enabled] MPS Revision [1.4] Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit 2-18
2-19
Onboard AC 97 Audio Onboard LAN Onboard LAN Boot ROM Serial Port1 Address Parallel Port Address Parallel Port Mode Parallel Port IRQ OnBoard Game/MIDI Port [Auto] [Enabled] [Disabled] [3F8/IRQ4] [Disabled] [Normal] [IRQ7] [Disabled] [Enter] to select 2-20
Advanced PCI/PnP Settings WARNING: Setting wrong values in below sections may cause system to malfunction. Plug And Play O/S [No] PCI Lantency Timer [64] Allocate IRQ to PCI VGA [Yes] Palette Snooping [Disabled] PCI IDE BusMaster [Enabled] IRQ3 [Available] IRQ4 [Available] IRQ5 [Available] IRQ7 [Available] IRQ9 [Available] IRQ10 [Available] IRQ11 [Available] IRQ14 [Available] IRQ15 [Available] NO: Lets the BIOS configure all the devices in the system. YES: Lets the operating system configure Plug and Play (PnP) devices not required for boot if your system has a Plug and Play operating system. 2-21
USB Configuration Module Version : 2.22.4-5.3 USB Devices Enabled: None Enables USB host controllers. USB Function Legacy USB Support USB 2.0 Controller USB 2.0 Controller Mode [Enabled] [Auto] [Enabled] [FullSpeed] USB Mass Storage Device Configuration 2-22
USB Mass Storage Device Configuration USB Mass Storage Reset Delay [20 Sec] No USB Mass Storage device detected 2-23
Suspend Mode Repost Video on S3 Resume ACPI 2.0 Support ACPI APIC Support BIOS -> AML ACPI table APM Configuration Hardware Monitor [Auto] [No] [No] [Enabled] [Enabled] Configure Select the CPU. ACPI state used for System Suspend. Select Screen Select Item Enter Go to Sub-screen F1 General Help F10 Save and Exit ESC Exit 2-24
Power Management/APM [Enabled] Video Power Down Mode [Disabled] Hard Disk Power Down Mode [Disabled] Suspend Time Out [Disabled] Throttle Slow Clock Ratio [50%] Enable or disable APM. Power Button Mode Restore on AC Power Loss Power On By RTC Alarm Power On By External Modems Power On By PCI Devices Power On By PS/2 Keyboard Power On By PS/2 Mouse [On/Off] [Power Off] [Disabled] [Disabled] [Disabled] [Disabled] [Disabled] 2-25
2-26
Hardware Monitor CPU Temperature CPU Temperature MB Temperature CPU Fan Speed Chassis Fan Speed [40.5ºC/102.5ºF] [33ªC/91ºF] [3260RPM] [N/A] VCORE Voltage [ 1.504V] 3.3V Voltage [ 3.360V] 5V Voltage [ 5.160V] 12V Voltage [11.328V] 2-27
Boot Settings Boot Device Priority Specifies the Boot Device Priority sequence. Boot Settings Configuration Security Boot Device Priority 1st Boot Device 2nd Boot Device 3rd Boot Device [1st FLOPPY DRIVE] [PM-ST320413A] [SM-ASUS CD-S360] Boot Settings Configuration Quick Boot Full Screen Logo AddOn ROM Display Mode Bootup Num-Lock Typematic Rate Boot to OS/2 Wait for F1 If Error Hit DEL Message Display Interrupt 19 Capture [Enabled] [Enabled] [Force BIOS] [On] [Fast] [No] [Enabled] [Enabled] [Disabled] Allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system. 2-28
2-29
Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Clear User Password <Enter> to change password. <Enter> again to disable password. Boot Sector Virus Protection [Disabled] Security Settings Supervisor Password : Installed User Password : Not Installed <Enter> to change password. <Enter> again to disabled password. Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection [Full Access] [Setup] [Disabled] 2-30
2-31
Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults Exit system setup after saving the changes. F10 key can be used for this operation. 2-32
3-1
3-2
3-3
3-4