Blu-ray Disc /DVD Home Theatre System BDV-N9100WL BDV-N7100WL GB Start here Quick start guide BDV-N7100WL BDV-N9100WL
1 What s in the box/setting up the speakers BDV-N9100WL 2 Connecting your TV BDV-N7100WL 3 Connecting other devices Main unit Front speakers Surround speakers Center speaker 4 The on-screen Easy Setup Subwoofer Surround amplifier 5 Playback and using other functions
What s in the box Speaker cords (5) Screws (BDV-N9100WL (16) / BDV-N7100WL (4)) Remote R03 (size AAA) batteries (2) FM wire antenna (aerial) or Calibration mic Wireless transceivers (2) Screw covers (4) (BDV-N7100WL) 03
1 Start by positioning the speakers according to the labels on the rear panel. You can also set the speakers in ALL FRONT position. For further details, visit: http://support.sony-europe.com/ 04
Next, connect the speakers to the main unit and surround amplifier. Refer to the supplied Speaker Installation Guide for assembling the speakers. 05
1 Insert the wireless transceivers into the main unit and surround amplifier for a cable-free connection. 06
2 To enjoy high-quality video and audio, connect via a High Speed HDMI cable (not supplied). If your TV has no HDMI ARC jack, you also need an optical digital cord (not supplied) to enjoy TV sound through the system speakers. 07
3 To connect your set-top box, game console, or digital satellite receiver, simply connect with an HDMI cable (not supplied). For FM radio, connect the supplied wire antenna (aerial) and extend it for the best reception. or 08
You can connect to the Internet and home network via a wireless LAN or LAN cable (not supplied). Network settings can be found in the home menu (page 14). For further details, visit: http://support.sony-europe.com/ Connect the AC power cords (mains leads) of the main unit and surround amplifier to a wall outlet (mains). To a broadband router 09
4 Connect the calibration mic and place where you would normally sit. This will be used to optimize the speakers in the next section to give you the best possible surround sound experience. The mic can be fully removed once this process is complete. 10
Press / to turn the system on. SETUP appears in the front panel display. To ready the system for use, go through the on-screen Easy Initial Settings using the supplied remote. This should only take a few minutes. If the setup screen is not displayed, select the correct AV input in your TV. Once [Easy Initial Settings are complete.] appears on the screen, select [Finish] and the system is ready to use. / ///, 11
5 To play a disc, press to open the disc tray, snap the disc (with the label facing upwards) onto the spindle, then press to close the disc tray. The LINK/STANDBY indicator on the surround amplifier turns green. If playback does not start automatically, select in the [Video], [Music], or [Photo] category, and press. 12
You can enjoy music on your smartphone, etc., via Bluetooth communication from your system. You can pair/connect your Bluetooth device by either: pressing the BLUETOOTH button, or holding your device near to the N mark on the main unit (for NFC compatible devices only). In either case, operation on your device is also required. For further details, visit: http://support.sony-europe.com/ BLUETOOTH 13
To access more features, simply press HOME. Examples: Listen to the radio through the system s speakers Preset radio stations Access Internet content Play files on the connected USB device You can make network settings via this menu when the main unit is connected to a broadband router. HOME 14
Presetting radio stations 1 Press FUNCTION repeatedly until FM appears in the front panel display. 2 Press and hold TUNING +/ until auto scanning starts. 3 Press OPTIONS. 4 Press / to select [Preset Memory], then press. 5 Press / to select the preset number you want, then press. 6 Repeat Steps 2 to 5 to store other stations. Selecting a preset station 1 Press FUNCTION repeatedly until FM appears in the front panel display. 2 Press PRESET +/ repeatedly to select the preset station. ///, OPTIONS HOME TUNING +/ PRESET +/ 15
Troubleshooting If you experience any of the following difficulties while using the system, use this troubleshooting guide to help remedy the problem before requesting repairs. Also consult the Operating Instructions on the following website: http://support.sony-europe.com/ The power does not turn on. Check that the AC power cord (mains lead) is securely connected to the wall outlet (mains). The system does not work normally. Disconnect the AC power cord (mains lead) from the wall outlet (mains), then reconnect after several minutes. The system does not output sound of the TV program when connected to a set-top box. Check the connections. Select the correct input of the system to which the set-top box is connected. There is no sound or wireless transmission is not activated. Check the status of the LINK/STANDBY indicator on the surround amplifier. Turns off. ēēcheck that the AC power cord (mains lead) of the surround amplifier is connected securely. ˎˎ ēēturn the surround amplifier on by pressing / on the surround amplifier. Flashes green quickly. ēē Press / on the surround amplifier. Insert the wireless transceiver into the surround amplifier correctly. Press / on the surround amplifier. ˎˎ ˎˎ Flashes red. ēēpress / to turn off the surround amplifier, and check the following items. Are the + and speaker cords short-circuited? Is anything blocking the ventilation opening of the surround amplifier? After checking the above items and fixing any problems, turn on the surround amplifier. If the cause of the problem cannot be found even after checking all the above items, consult your nearest Sony dealer. Flashes green or orange slowly or turns red. ēēmake sure that the wireless transceiver is inserted correctly into the main unit. ˎˎ ēēsound transmission is poor. Move the surround amplifier so that the LINK/STANDBY indicator turns green or orange. ēēmove the system away from other wireless devices. ēēavoid using any other wireless devices. Turns green or orange. ēēcheck the speaker connections. ˎˎ There is no sound from surround speakers. Press OPTION and check that [Sound Mode] is set to [Auto]. A disc does not play. The region code of the disc does not match the system. Moisture has condensed on the lenses inside the main unit. Remove the disc and leave the main unit turned on for about half an hour. The disc is not correctly finalized. Reducing power usage to less than 0.3 W in Standby Mode Press HOME, and then press /// to select [Setup]. Check that the following settings are made: ˎˎ Select [System Settings] > [HDMI Settings] > [Control for HDMI], then set [Control for HDMI] to [Off]. ˎˎ Select [System Settings] > [Quick Start Mode], then set [Quick Start Mode] to [Off]. ˎˎ Select [Network Settings] > [Remote Start], then set [Remote Start] to [Off]. 16
This quick start guide saves paper To save natural resources, Sony has drastically reduced paper by no longer including full printed manuals. However, full operating instructions, and more, can be found online: http://support.sony-europe.com/ 4-458-324-12(1) 2013 Sony Corporation Printed in Malaysia (1)