1
Main H/W Monitor Boot Security Exit System Overview System Time System Date BIOS Version Processor Type Processor Speed : 3400MHz Microcode Update : F64/4 Cache Size : 2048KB Total Memory DDRII 1 DDRII 2 DDRII 3 DDRII 4 [ 14:00:09] [Tue 10/17/2007] : 4Core1333-GLAN P1.00 : Intel (R) CPU 3.40GHz (64bit) : 1024MB : 1024MB/333MHz (DDRII667) :None :None :None Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. +- Change Field Tab Select Field Main H/W Monitor Boot Security Exit Settings Configure CPU WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration Enter Go to Sub Screen 2
CPU Configuration Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) Boot Failure Guard Spread Spectrum [200] [100] Ratio Status Unlocked (Max:17, Min:12) Ratio Actual Value 17 Enhanced Halt State Max CPUID Value Limit CPU Thermal Throttling No-Excute Memory Protection Hyper Threading Technology Intel (R) SpeedStep (tm) tech. Select the over clock mode. +- Change Option F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 3
4
Chipset Configuration OnBoard HD Audio Front Panel OnBoard Lan DRAM Voltage NB Core Voltage VTT Voltage Memory Remap Feature DRAM Frequency Flexibility Option DRAM CAS# Latency DRAM RAS# to CAS# Delay DRAM RAS# Precharge DRAM RAS# Activate to Precha Primary Graphics Adapter [PCI] ENABLE: Allow remapping of overlapped PCI memory above the total physical memory. DISABLE: Do not allow remapping of memory. + - Change Option 5
6
ACPI Configuration Suspend To RAM Repost Video on STR Resume Restore on AC/Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On ACPI HPET Table [No] [Power Off] Select auto-detect or disable the STR feature. +- Change Option 7
IDE Configuration ATA/IDE Configuration SATAII 1 SATAII 2 SATAII 3 SATAII 4 IDE1 Master IDE2 Slave [Enhanced] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] Set [Compatible] when Legacy OS (MS-DOS, Win NT) is used. Set [Enhanced] when Native OS (Win 2000/XP) is used. +- Change Option F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit v02.54 (C) Copyright 1985-2003, American Megatrends, Inc. [SATA 1, SATA 2, [SATA 1, SATA 3, [IDE 1, SATA 2, SATA 3, SATA 4] IDE 1] SATA 4] SATAII_1 (Port0), SATAII_2 (Port1) SATAII_3 (Port2), SATAII_4 (Port3) SATAII_1 (Port0) SATAII_3 (Port2) SATAII_2 (Port1) SATAII_4 (Port3) 8
Primary IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer :Hard Disk :ST340014A :40.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-5 :Supported Select the type of device connected to the system. +- Change Option TAII_2 (Port1) TAII_4 (Port3) 9
10
PCI / PnP Settings PCI Latency Timer PCI IDE BusMaster [32] ValueinunitsofPCI clocks for PCI device latency timer register. +- Change Option Floppy Configuration 1 Floppy A [1.44 MB 3 2 "] Select the type of floppy drive connected to the system. +- Change Option 11
Configure Win627EHF Super IO Chipset OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ [3F8 / IRQ4] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] Allow BIOS to Enable or Disable Floppy Controller. +- Change Option 12
USB Configuration USB Controller USB 2.0 Support Legacy USB Support To enable or disable the onboard USB controllers. +- Change Option 13
Main H/W Monitor Boot Security Exit Hardware Health Event Monitoring CPU Temperature M / B Temperature : 37C/98F : 31C/87F Enable/Disable CPU Quiet Fan Function. CPU Fan Speed Chassis Fan Speed : 3400 RPM :N/A Vcore + 3.30V + 5.00V + 12.00V CPU Quiet Fan : 1.629V : 3.306V : 5.067V : 11.890V F1 F9 F10 ESC General Help Load Defaults Save and Exit Exit v02.54 (C) Copyright 1985-2003, American Megatrends, Inc. 14
Main H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration Configure Settings during System Boot. 1st Boot Device 2nd Boot Device 3rd Boot Device 4th Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM - HDS722580VL] [CD / DVD: 3S - CD - ROM C] [USB] Enter Go to Sub Screen Boot Boot Settings Configuration Boot From Onboard LAN Bootup Num-Lock [On] To enable or disable the boot from onboard LAN feature. + - Change Option 15
Main H/W Monitor Boot Security Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Install or Change the password. Enter Change 16
Main H/W Monitro Boot Security Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Enter Go to Sub Screen 17