DP4 DOOR PHONE For Technical Assistance Please Phone: (07) 5596 5128
TABLE OF CONTENTS Description Page 3 Door Phone Dimensions Page 4 Description Continued Page 5 Door Phone Range Page 6 Door Phone Performance Page 7 Camera Power Page 8 Camera Wiring Page 9 Mounting the Door Phone Page 10 Operation Summary Page 11 Balance Pot Adjustment Pages 12-13 Wiring Diagrams Pages 14-15 Wiring Connection Pages 16-17 Surface Mounting Kits Page 18 Door Phone Covers Page 19 Specifications and Warranty Information Pages 20 Page 2 National Communications
DESCRIPTION Our Model DP4 Flush Mount Door Phones are specifically designed for connection to a Natcomm Door Station Controller (Models DS1-DS6). DP4 incorporates a Low Light, High Resolution CCD Colour Camera, fitted in a sealed plastic enclosure. The Camera Circuit uses a High Resolution SONY sensor, which is designed to operate to at low light levels, where moon light will provide good images. Resolution: 380 lines S/N Ratio: 46dB Image Sensor: 1/4" CCD Light Sensitivity: 2 Lux A/V Connectors: BNC The Camera is powered by the 4 wire connection to the Door Phone and separate power is not required unless the DP4 is to be located more than 70m away. If DP4 will be located more than 70m from the Door Phone controller, please advise Natcomm or your Dealer and a separate 12V regulated Power adaptor will be provided at no charge. (see page 8). DP4 has a BNC Video Output, suitable for direct connection to coaxial cable. Optional CAT5 Video Baluns are available at extra cost, should you wish to forward the video by 2 wires of a CAT5 cable. See page 9. The Camera Lens provides a viewing angle of 92 degrees, and is fitted behind a sealed 12mm transparent window. DP4 has a polymer coated 316 Marine Grade Stainless Steel fascia plate and can be mounted either horizontally or vertically. Please order your unit set up for Vertical or Horizontal orientation, so the Camera and the BELL of the Touch Sensitive switch are orientated appropriately. Fitting this unit in the alternative orientation will cause the Video image to be 90 degrees out. There are 2 Models of DP4 : DP4-V - Vertical Orientation DP4-H - Horizontal Orientation National Communications Page 3
MODEL DP4 DOOR PHONE Page 4 National Communications
DESCRIPTION continued Our DP4 Door Phones can operate at distances of up to 300 meters from the Controller, providing high quality cabling such as CAT5 is used. Note - When located more than 70m from the Door Phone controller, the Camera will need to use a separate power source by using the supplied 12V regulated Power adaptor. This additional Power Adaptor wil be supplied separately on request at no additional charge. All DP4 units are designed to be highly WEATHER RESISTANT and they have proven to be reliable over long periods of time, providing they are not exposed to direct rain. The Speaker is made of a plastic mylar material and great effort has been taken to maximise weather proofing all electronic components. Note - DP4 Door Phones are not WATER PROOF. Whenever your Door Phone is likely to be exposed to RAIN, an optional DOOR PHONE COVER or a SURFACE MOUNTING KIT with Rain Deflector should be used. They will ensure that rain water cannot gradually permeate through to the electronics of the Door Phone which can cause unreliable operation and premature failure of this device. See Pages 18-19. Up to two of our Door Phones can be connected to the one DOOR STATION (CONTROLLER). This allows for a Door Phone to be located at two different locations. In this situation, the Door Phone devices are connected in parallel (see wiring connection). Our DP4 s are designed for wall or pole mounting at a height of approximately 1.5 meters (5 feet). Visitors should stand within 0.5 meters (20 inches) of the Door Phone for best results. Our DP4 units incorporate a touch sensitive switch, in order to further improve it s long term reliability. This switch is activated by a brief touch. National Communications Page 5
DOOR PHONE RANGE A choice of Five Door Phones are provided for use with our range of Door Station Controller units : Model DP1 - SURFACE MOUNT Moulded plastic unit, designed for easy mounting direct onto your wall surface. Vertical orientation only. (100mm Wide, 133mm High, 32mm Depth). Model DP2 - FLUSH MOUNT Compact Size Marine Grade Stainless Steel face plate. Touch Switch operation. Night illumination. Available in Vertical or Horizontal orientation. Optional Surface Mounting Kit is available. (107mm Wide, 204mm High, 30mm Depth). Model DP3 - FLUSH MOUNT Standard Size Marine Grade Stainless Steel face plate. Touch Switch operation. Night illumination. Available in Vertical or Horizontal orientation. Has a 12 mm hole and threaded mounting studs to allow for a Digital Camera to be fitted. Optional Surface Mounting Kit is available. (130mm Wide, 264mm High, 30mm Depth). Model DP4 - FLUSH MOUNT Standard Size Fitted with a high resolution, low light Digital Colour Camera. Marine Grade Stainless Steel face plate. Touch Switch operation. Night illumination. Available in Vertical or Horizontal orientation. Optional Surface Mounting Kit is available. (130mm Wide, 264mm High, 37mm Depth). Model DP5 - FLUSH MOUNT Standard Size Fitted with an intelligent Pedestrian Access Keypad. Touch switch operation with 99 User Codes Marine Grade Stainless Steel face plate. Blue and White LED Night illumination. Available in Vertical or Horizontal orientation. Optional Surface Mounting Kit is available. (130mm Wide, 264mm High, 30mm Depth). Page 6 National Communications
DOOR PHONE PERFORMANCE This product is IDEAL for RESIDENTIAL USE or COMMERCIAL USE, where ROAD NOISE is NOT HIGH. It is not designed for INDUSTRIAL USE where ambient noise will be constantly high. The volume of the audio communication on the internal phones should be comfortably audible (a similar level to a telephone call) providing : The person at the Door Phone is talking directly towards the Door Phone and at a distance of no more than 1 to 2 feet away (max 500-600 mm). The Door Phone is mounted at a height of about 1.5 meters (5 feet). You can mount at a lower level to allow for very young children, but volume will suffer. No plates or other material are placed over the front face of the Door phone. Our Door Phone Cover accessory, or a properly designed Rain Hood will not affect performance. The volume of the audio communication at the Door Phone should be comfortably audible, providing : There is not excessive road noise or other noise near the Door Phone. This will affect the automatic gain circuit used in this device. That high quality ADSL FILTERING is fitted ahead of the DS CONTROL- LER where ADSL is used on the same line. If you do not do so, volume in both directions will be affected. Refer to your Door Station Controller User Guide for detailed information on the use of ADSL with this product. National Communications Page 7
CAMERA POWER The Integrated Camera is powered direct from the Door Phone, which receives it s power via the 4 wire connection from the DS Controller. However, the power consumption of the Camera is approximately 150 ma and this cannot be supported over distances greater than 70 meters. When operating the Camera at distances greater than 70m from the Door Phone controller, you will need to use a separate 12VDC regulated Power adaptor to separately power the Camera. This additional Power Adaptor wil be supplied separately on request at no additional charge. INSTRUCTIONS FOR USE OF THE SEPARATE CAMERA POWER SUPPLY 1. Remove the Power Cable connecting to the Camera assembly power socket. Seal the removed cable and plug with waterproof insulating tape to prevent future shorting. 2. Connect the Power Plug of the supplied 12V DC Regulated Power Supply to the power socket of the Camera assembly. Connect the supplied 12V DC Regulated Power Supply to a 240V Power Source. Camera Assembly Power Cable Video Cable Note - You must use the supplied 12VDC Regulated Power Adaptor or the Camera may be damaged. Page 8 National Communications
CAMERA WIRING DP4 provides a BNC output for Video, which can be connected to standard TV s, dedicated Video display units or both. If IP Video is required, the DP4 video output should be connected to an Analogue to Video IP Converter, such as the AXIS 241S. You can use either Coaxial cable or CAT5 cable to connect video to your Video display units. As only 4 wires of an 8 wire CAT5 cable are required for the Door Phone, 4 wires are unused, unless One or Two Door locks are used in conjunction with the Door Phone. If only One Door Lock is used, then 2 wires are still available for Video. If Two Door Locks are used, there will be no spare wires and a separate CAT5 cable or a Coaxial cable will be needed for Video. If you plan to use 2 wires of a CAT5 cable, then you will need to use a pair of CAT5 Video Baluns to transfer the video signal. One Balun will connect to the BNC output from the DP4 and the other will connect to your Video display device. A single pair of CAT5 cable is used between the Baluns. Good Quality Baluns, such as those provided by Natcomm (see below) will allow for good quality video over 100 s of meters of CAT5 cable. CAT5 Video Baluns National Communications Page 9
MOUNTING THE DOOR PHONE The DOOR PHONE should be mounted at the average face height of 1.5 meter (5 feet) for optimum performance. The main body of the DP4 unit is designed to be recessed into a wall surface. It can be fitted horizontally or vertically. To assist installation, a Galvanised Iron Wall Mount box (WMB) is supplied which should be fitted within the wall cavity is supplied. A recess area of : 255 mm, 93mm and 40mm (D) should be prepared for insertion of the Wall Mount Box. Alternatively, a brick can be removed. WMB is the same height and width of a standard brick. The Wall Mount Box should then be securely fixed within the recessed cavity using nails, dyna bolts or silicone. DP4 is then screwed onto the WMB by using 2 supplied stainless steel screws. SURFACE MOUNTING KITS Optional Stainless Steel Surface Mounting Kits are available for all Natcomm Door Phones, so that your Door Phone can be mounted ONTO a wall surface, rather than into it. See page 18 for further detail. Page 10 National Communications
OPERATION After initial Power Up, the Door Phone will take up to 5 seconds to initialise. To commence a Door Phone call, you should press the BELL on the Door Phone briefly. The LED will then turn OFF and you will hear a RING TONE until the call is answered. This Door Phone will trigger a Door Station Controller that will either RING all the telephones connected to your telephone line or it will operate with a PABX system. As soon as the call is answered, you will be able to communicate with loud and clear call quality. If this Door Phone is connected to a Model DS6 Controller, you will also have the ability to connect to an external telephone number, or cell phone whenever the site is unattended. Our Door Phones use an intelligent, fast switching half duplex communication method, as this provides for highest volume levels and eliminates feedback in areas with low to moderate background noise levels. This method is not suitable for areas where high background noise levels are prsent.. After your Door Phone call is completed, there will be a delay of approximately 5 seconds before the unit has reset and is ready for the next call. For maximum clarity, it may be necessary to adjust the Balance Pot (see page 12-13). IMPORTANT NOTE WHEN TESTING YOUR DOOR PHONE DO NOT USE A TELEPHONE IN CLOSE PROXIMITY AS FEEDBACK WILL CAUSE LOSS OF VOLUME. National Communications Page 11
BALANCE POT ADJUSTMENT Balance Pot is located under this sealing plug. You will need to use a small standard blade screwdriver. Page 12 National Communications
BALANCE POT ADJUSTMENT Your DOOR PHONE is preset at the factory for maximum performance. Our sophisticated circuitry is designed to measure the background noise present at your site and then apply maximum gain. In most cases you SHOULD NOT NEED TO MAKE ANY ADJUSTMENTS. If you are using Two Door Phones, it is possible that you will need to adjust the POT of one or both Door Phones to suit your specific site conditions. The balance POT is provided in case you experience one of the following : Audio is distorted. Audio (speech) can only be heard in 1 direction. Should you encounter one of these problems, you will need to make slow careful adjustments in one direction or the other until speech can be heard in both directions and without distortion. The balance POT is located on the back of DOOR PHONE under a small 3mm removable black plastic plug. It should be adjusted using a small flat blade screwdriver. IMPORTANT NOTES 1) You will require TWO PEOPLE to adjust your Door Phone. 2) Wait 10 seconds after answering before adjusting the Pot. 3) DO NOT USE A TELEPHONE IN CLOSE PROXIMITY TO THE DOOR PHONE, as feedback interference will affect the Balance Pot settings. 4) The Balance POT does not increase volume. Moving it when unnecessary may cause a deterioration in audio quality or a loss of audio in 1 direction. National Communications Page 13
CONTROLLER WIRING SUPPLIED CABLE BLUE LOCK 2 ORANGE LOCK 1 BLACK POWER RED AUDIO LOCK 2 WHITE LOCK 1 BROWN POWER YELLOW AUDIO GREEN CAT5 CABLE or SOLID CORE CABLE The colours used are those of the wires in the supplied Interface box. Page 14 National Communications
DOOR PHONE WIRING BLACK POWER RED AUDIO POWER YELLOW AUDIO GREEN CAT5 CABLE or SOLID CORE CABLE The colours used are those of the wires in the supplied Interface box. National Communications Page 15
WIRING CONNECTION Solid core cable such as CAT5 should be used to connect between the DS Controller unit and the Door Phone unit. The DS Controller unit has a standard 8 wire RJ45 connector. The Door Phone uses a 4 position Phoenix Style plug. Four wires are used to connect the Door Phone to the DS Controller unit. Two wires are required for each internal relay used for Lock control. A maximum of 8 wires is required for installation, so a CAT5 cable is ideal An external connection box with 8 screw terminals is supplied with your DS Controller unit. The connection box provides a convenient means of connecting the 2 or 4 wires used for 1 or 2 Gate or Door locks to the internal relays of the DS Controller. The connection box connects to the DS Controller unit via the supplied short RJ45 cable. If Lock control is not required, you will not need to use this box. Where LOCK CONTROL is not required, you can bypass the connection box and connect your CAT5 cable direct to the DS Controller. For details see page 17. There is a 4 position Phoenix Style press in connector socket on the rear of the Door Phone, to which you connect the Audio and Power wires. Two wires are required for the AUDIO SIGNAL and Two wires are used to provide POWER to the unit. The Audio signal connects to the middle Two positions of the socket. The Power input connects to the outside Two positions of the socket. Note : The polarity of the Audio signal and power connections is not important and can be reversed. Page 16 National Communications
The RED WIRE of the connection box, carries one leg of the Audio Signal. It must connect to EITHER centre position (pin 2 or 3) of the supplied Phoenix plug. Note - Polarity is not important. The GREEN WIRE of the connection box, carries the other leg of the Audio Signal. It must connect to EITHER centre position (pin 2 or 3) of the supplied Phoenix plug. Note - Polarity is not important. The BLACK WIRE of the connection box, carries one leg of the 12V Power input. It must connect to EITHER outer position (pin 1 or 4) of the Phoenix plug. Note - Polarity is not important. The YELLOW WIRE of the connection box, carries one leg of the 12V Power input. It must connect to EITHER outer position (1 or 4) of the Phoenix plug. Note - Polarity is not important. Where Two Door Phones are to be used, they should both connect to the same contacts of the interface box (ie: parallel connection). The ORANGE and BROWN WIRES of the connection box connect to the Internal Relay used for Lock 1. Connect ONE leg of the 12V power for Lock 1 to these terminals, by cutting the wire in half and fit one part to the screw terminal connecting to the Orange wire and the other to the screw terminal connected to the Brown wire. Polarity is not important. The BLUE and WHITE WIRES of the connection box connect to the Internal Relay used for Lock 2. Connect ONE leg of the 12V power for Lock 2 to these terminals, by cutting the wire in half and fit one part to the screw terminal connecting to the Blue wire and the other half to the screw terminal connected to the White wire. Polarity is not important. BYPASS CONNECTION BOX If you don t plan to use the connection box, then you can connect the CAT5 cable direct to the DS Control unit and Door Phone, as follows : AUDIO CONNECTION (polarity is not important) The centre 2 pins of the DS Controller RJ socket need to connect to the centre 2 positions of the DP2 Phoenix socket. POWER CONNECTION (polarity is not important) The 2 pins either side of the centre 2 pins of the DS Controller socket connect to the 2 outer positions of the 4 pin Phoenix socket. National Communications Page 17
SURFACE MOUNTING KITS Stainless Steel Surface Mounting Kits are available for all Door Phones, so that your Door Phone can be mounted ONTO a wall surface, rather than into it. 4 separate surface mounting kits are available, to cater for the two different sized Door Phones (DP2-DP5) that can be mounted vertically or horizontally. All kits have an integrated Rain Deflector. Model SMK2-V for DP2 units mounted vertically Model SMK2-H for DP2 units mounted horizontally Model SMK3-V for DP3, DP4, DP5 mounted vertically Model SMK3-H for DP3, DP4, DP5 mounted horizontally Page 18 National Communications
DOOR PHONE COVER If your Door Phone is not under cover, a strong transparent DOOR PHONE COVER is essential to ensure that water from rain cannot gradually permeate through to the electronics of the Door Phone which can cause unreliable operation and can eventually lead to permanent failure of this device. COVERS FOR VERTICAL MOUNTED DOOR PHONES Model DPC1-V : for Model DP1 Door Phone Model DPC2-V : for Model DP2 Door Phone Model DPC3-V : for Models DP3, DP4, DP5 COVERS FOR HORIZONTAL MOUNTED DOOR PHONES Model DPC2-H : for Model DP2 Door Phone Model DPC3-H : for Models DP3, DP4, DP5 National Communications Page 19
SPECIFICATIONS Dimensions(all in mm) : 204 mm x 107 mm x 43 (D) Weight : 540g Communications Connector : Phoenix 4 pin Video Connector : BNC ACMA COMPLIANT : Supplier Number N 782 WARRANTY This device is guaranteed against defects from workmanship for a period of two years (24 months) from the date of purchase. In the event of failure, you should return the product, along with proof of purchase date, and a written statement about the nature of the problem. This Warranty shall not apply to any unit which has been subject to alteration, modification, abuse, negligence, accident, external voltage/ lightning surge or used in any manner contrary to these instructions. The obligation is solely to repair or replace the product. The warrantor is not liable for any incidental or consequential damages due to such defects. The user is responsible for freight costs to the repair point. The warrantor will be responsible for freight costs in returning this unit back to the user. Damage caused to this device or attached equipment, by lightning strikes or over voltage surge is not covered under this warranty. CASE SEALED AT FACTORY OPENING THE CASE VOIDS THE WARRANTY Page 20 National Communications