INSTRUCTION MANUAL * Design and Specifications are subject to change without notice. ver. 1.0 PRINTED IN KOREA
INSTRUCTION MANUAL Thank you for purchasing this product. For proper usage and application, please read this instruction manual thoroughly. CM-42A TILT CAMERA FOR VEHICLES
CONTENT TILT CAMERA FOR VEHICLES SAFEGUARD INSTRUCTIONS... 3 FEATURES...4 BOX CONTENT INSTALLATION CONNECTION... 4... 5... 6 CLEANING and GENERAL MAINTENANCE... 7 SPECIFICATIONS... 8
SAFEGUARD INSTRUCTIONS TILT CAMERA FOR VEHICLES Please pay attention to the warnings and cautions below in order to prevent potential risks. WARNING and CAUTION symbols are divided according to the different risk levels. WARNING CAUTION May cause bodily harm or even death if the user ignores the warnings in the safety rules. May cause damage or shorten usage time of the product if the user ignores the cautions in the safety rules. WARNING In case that the power cable cord touches a metal case, cover it with a friction tape. - Short circuit or disconnection of wire may cause a fire or accident. Do not use bolts or nuts from parts of the vehicle. - Using bolt or nuts from steering column or break may cause an accident. Let professional engineers or the sale store install the camera. - It requires the experience and skills of professional engineers for proper installation and wiring. After installing the camera, check if the break lamp, head lamp and wipe work properly. The camera has to be installed with DC 12V to the vehicle. CAUTION Do not disassemble the device. - It may cause a fire or malfunction of the device. Do not install the camera with big distance the vehicle. - It may harm the pedestrians. Do not let the extension cable pass through the seat rail. Wire the cables properly. - It may cause a fire or an accident. Do not install the camera bracket on glass surface. - Use screws for the installation of the camera bracket.
FEATURE 1 TILT CAMERA FOR VEHICLES 1/3 SONY COLOR CCD image sensor 6 pcs of IR LEDs for night view Built-in microphone Built-in heating function Waterproof (IP-67) Aluminum die-casting housing Night vision using the CdS sensor. Automaticall tilt camera lens Normal Driving Rear view angle 0 degree Backing the car Rear view angle turned to the floor about 35 degree BOX CONTENT 2 TILT CAMERA FOR VEHICLES Tilt Camera Sun Visor Camera Bracket Instruction Manual CM-112AHT Accessory Pack Extension Cable (70ft) Instruction Manual
INSTALLATION 3 TILT CAMERA FOR VEHICLES 1. Determine a position and a direction of installation so that the back area of your vehicle can be effectively seen on the monitor screen. 2. Fix the camera bracket to the vehicle using the provided adhesive tape and the tapping screws with the spring washers. 3. Fix the camera between the camera bracket and sun visor by using machine screws. Adjust the angle of the camera and fasten the screws firmly. 4. Run the cable from the monitor to the camera. CM-112AHT Camera Connector 1. CAMERA B+ (DC +12V) 2. HEATING B+ (DC +12V) 3. STAND BY 4. VIDEO OUT 5. AUDIO OUT 6. N.C 7. GND Fix the camera bracket to the vehicle using the provided adhesive tape and the tapping screws with the spring washers. A TAPPING SCREW TH M4x10 SPRING WASHER M4 FLAT WASHER M4 B SEM S MACHINE SCREW M3x7 C MACHINE SCREW PHW M3x5 Installation example Fix the camera between the bracket and sun visor by using machine screws. Adjust the angle of the camera and fasten the screws firmly.
CONNECTION 4 TILT CAMERA FOR VEHICLES Insulation Tape Tilt Camera Monitor (Option) Extension Cable (70ft) Before making the connection, disconnect the ground terminal of the car battery to avoid short circuiting. Before inserting a plug, the pin specifications need to be checked and the plug should be firmly inserted to the jack or connector. If it has been inserted in the wrong direction, it may cause malfunction. After the extension cable has been connected, it needs to be turned in the right direction as described on the illustration above. 6
CLEANING and GENERAL MAINTENANCE 5 TILT CAMERA FOR VEHICLES Clean the unit with a slightly damp soft cloth. Use a mild household detergent. Never use strong solvents such as thinner or benzine as they might damage the finish of the unit. CLEANING Unplug or power off the device before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. OBJECT and LIQUID ENTRY Never push objects of any kind into the camera through holes as they may touch dangerous voltage points or short-out parts that could result in a fire resulting from an electric shock. Never spill any kind of liquid on the product. SERVICING Do not attempt to service this system by yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personal. SPECIFICATIONS 6 TILT CAMERA FOR VEHICLES Pick-up device View of angle Minimum illumination Input voltage Operating temperature Dimensions Weight Accessories NTSC PAL 1/3 250,000 pixels COLOR CCD 1/3 290,000 pixels COLOR CCD 95 (H) / 70 (V) / 120 (D) 0.1 lux DC 12V / 200mA Max. -15 C ~ 65 C (5 F ~ 149 F) 78.4(W) x 52.0(H) x 56.5(D) mm / 3.09(W) x 2.04(H) x 2.22(D) (Camera Only) 0.4kg / 0.88lbs (including bracket and sunvisor) Adhesive tape... 1 Screws set... 9 Insulation tape... 1 7