1
Main H/W Monitor Boot Security Exit System Overview System Time System Date BIOS Version Processor Type Processor Speed Microcode Update : 60FB1/0 L1 Cache Size : 256KB L2 Cache Size : 1024KB Total Memory DDRII1 DDRII2 DDRII3 DDRII4 [ 17:00:09] [Wed 11/14/2007] : ALiveNF5-VSTA BIOS P1.0 : AMD Athlon(tm) 64 X2 Dual Core Processor 3600+ (64bit) : 1900MHz : 512MB Single-Channel Memory Mode : 512MB/266MHz (DDRII533) :None :None :None Use [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system Time. +- Change Field Tab Select Field Main H/W Monitor Boot Security Exit Settings Options for CPU WARNING : Setting wrong values in below sections may cause system to malfunction. CPU Configuration Chipset Configuration ACPI Configuration IDE Configuration PCIPnP Configuration Floppy Configuration SuperIO Configuration USB Configuration Enter Go to Sub Screen 2
CPU Configuration AM2 Boost Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) Boot Failure Guard CPU/LDT Spread Spectrum PCIE Spread Spectrum SATA Spread Spectrum Cool'n'Quiet Secure Virtual Machine Enhanced Halt State Processor Maximum Frequency Processor Maximum Voltage Multiplier/Voltage Change Memory Clock Flexibility Option [200] [100] [0.75% Hershey] x9.5 1900 MHz 1.350 V If AUTO, multiplier and voltage will be left at the rated frequency/voltage. If Manual, multiplier and voltage will be set based on User Selection in Setup. F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 3
CPU Configuration AM2 Boost Overclock Mode CPU Frequency (MHz) PCIE Frequency (MHz) Boot Failure Guard CPU/LDT Spread Spectrum PCIE Spread Spectrum SATA Spread Spectrum Cool'n'Quiet Secure Virtual Machine Enhanced Halt State Processor Maximum Frequency Processor Maximum Voltage Multiplier/Voltage Change Processor Frequency Processor Voltage [200] [100] [0.75% Hershey] x9.5 1900 MHz 1.350 V [Manual] [x8] [1.500V] If AUTO, multiplier and voltage will be left at the rated frequency/voltage. If Manual, multiplier and voltage will be set based on User Selection in Setup. F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit 4
5
6
Chipset Settings To set DRAM Voltage. Onboard LAN Onboard HD Audio Front Panel ASRock WiFi Primary Graphics Adapter CPU-NB Link Speed CPU-NB Link Width DRAM Voltage [PCI] + - Change Option 7
ACPI Settings Suspend To RAM Repost Video on STR Resume Away Mode Support Restore on AC / Power Loss Ring-In Power On PCI Devices Power On PS / 2 Keyboard Power On RTC Alarm Power On ACPI HPET Table [No] [Power Off] Select auto-detect or disable the STR feature. 8
IDE Configuration OnBoard IDE Controller OnBoard SATA Controller SATA Operation Mode IDE1 Master IDE1 Slave SATAII_1 SATAII_2 SATAII_3 SATAII_4 [non-raid] [Hard Disk] [Not Detected] [Not Detected] [Not Detected] [Not Detected] [Not Detected] ENABLED: enables the integrated IDE Controller. DISABLED: disables the integrated IDE Controller. F1 General Help F9 Load Defaults F10 Save and Exit ESC Exit IDE Master Device Vendor Size LBA Mode Block Mode PIO Mode Async DMA Ultra DMA S.M.A.R.T. :Hard Disk :MAXTOR 6L080J4 :80.0 GB :Supported :16Sectors :4 :MultiWord DMA-2 :Ultra DMA-6 :Supported Type LBA/Large Mode Block (Multi-Sector Transfer) PIO Mode DMA Mode S.M.A.R.T. 32Bit Data Transfer Select the type of device connected to the system. 9
10
PCI / PnP Settings PCI Latency Timer PCI IDE BusMaster [32] ValueinunitsofPCI clocks for PCI device latency timer register. Floppy Configuration 1 Floppy A [1.44 MB 3 2 "] Select the type of floppy drive connected to the system. 11
Configure Super IO Chipset OnBoard Floppy Controller Serial Port Address Infrared Port Address Parallel Port Address Parallel Port Mode EPP Version ECP Mode DMA Channel Parallel Port IRQ [3F8 / IRQ4] [378] [ECP + EPP] [1.9] [DMA3] [IRQ7] Allow BIOS to Enable or Disable Floppy Controller. 12
USB Configuration USB Controller USB 2.0 Support Legacy USB Support To enable or disable the onboard USB controllers. 13
Main H/W Monitor Boot Security Exit Hardware Health Event Monitoring CPU Temperature M / B Temperature : 37C/98F : 31C/87F CPU Fan Speed Chassis Fan Speed : 2833 RPM :N/A Vcore + 3.30V + 5.00V + 12.00V CPU Quiet Fan : 1.532 V : 3.129 V : 4.877 V : 11.741 V F1 F9 F10 ESC General Help Load Defaults Save and Exit Exit Main H/W Monitor Boot Security Exit Boot Settings Boot Settings Configuration Configure Settings during System Boot. 1st Boot Device 2nd Boot Device 3rd Boot Device 4th Boot Device Hard Disk Drives Removable Drives CD/DVD Drives [1st Floppy Device] [HDD: PM-MAXTOR 6L08] [CD/DVD: SM-CD-ROM] [USB] Enter Go to Sub Screen 14
Boot Boot Settings Configuration Boot From Onboard LAN Bootup Num-Lock [On] To enable or disable the boot from network feature. + - Change Option Main H/W Monitor Boot Security Exit Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password Change User Password Install or Change the password. Enter Change 15
Main H/W Monitro Boot Security Exit Exit Options Save Changes and Exit Discard Changes and Exit Discard Changes Load Optimal Defaults Exit system setup after saving the changes. F10 key can be used for this operation. Enter Go to Sub Screen 16