ITX-i230D Form Factor Mini-ITX Mini-ITX Industrial Motherboard CPU Soldered onboard Intel Celeron J900 Processor Quick Installation Guide Version.0 Video HDMI/LVDS I/O SATA/ USB 2.0/ USB3.0/ COM LAN RTL8G-CG Gigabit Ethernet controller Audio Realtek ALC662 + ALC3, Mic-in/Line-out Technical Support If you have any technical difficulties, please consult the user s manual first at: ftp://ftp.arbor.com.tw/pub/manual Contact our customer service at the following addresses if your problem persists. http://www.arbor.com.tw E-mail: info@arbor.com.tw Declaration of Conformity FCC Class A This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions : () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Copyright All Rights Reserved. 40402300000P - -
Packing List Before you begin to install your single board, please make sure that the following materials have been shipped: x ITX-i230D Mini-ITX industrial motherboard x Driver CD x Quick Installation Guide x I/O bracket x DC 2.5 Jack to 7.4 Plug Cable If any of the above items is damaged or missing, contact your vendor immediately. Ordering Information ITX-i230D Intel Celeron Processor J900 Embedded Mini-ITX motherboard Optional Accessories CBK-07-230D-00 Cable Kit x Two Ports USB cable 3 x One Port USB cables x Two Ports SATA Power cable 2 x SATA cables - 2 -
The Installation Paths of CD Driver Windows 8 & 8. Driver Path CHIPSET \Chipset\SetupChipset_0.0.3_PC \Graphics\WIN8_32\5.33.22.362 GRAPHIC \Graphics\WIN8_64\5.33.22.64.362 ETHERNET \Ethernet\Realtek\Win8_8.\Install_Win8_8._803_0522204 \Audio\32bit_Win7_Win8_Win8_R275 AUDIO \Audio\64bit_Win7_Win8_Win8_R275 TXE \TXE\Installers SERIAL IO \Serial IO\SerialIO_Installer_Win8._64bit_WW23 Windows 7 Driver CHIPSET GRAPHIC ETHERNET AUDIO TXE USB3.0 SERIAL IO Path \Chipset\SetupChipset_0.0.3_PC \Graphics\WIN7_32\Intel_EMGD.WIN7_PC_Version_36_5_0_073 \Graphics\WIN7_64\Intel_EMGD.WIN7_PC_Version_37_5_0_073 \Ethernet\Realtek\Win7\Install_Win7_7085_0522204 \Audio\32bit_Win7_Win8_Win8_R275 \Audio\64bit_Win7_Win8_Win8_R275 \TXE\Installers (For 64-bit Windows only) \USB3.0\Intel(R) USB 3.0 extensible Host Controller_ Win7_32bit_64bit_R3.0.0.33 \Serial IO\Intel Processor IO Drivers_Win7_32bit_64bit_Gold_v2.0-3 -
Specifications Form Factor CPU System Memory Graphic Chipset Graphic Interface Serial Port Expansion Bus Ethernet BIOS Audio Serial ATA USB Power Requirement Operation Temp. Operating Humidity Mini-ITX industrial motherboard Soldered onboard Intel Celeron J900 quad-core Processor x 204-pin DDR3 SO-DIMM socket supporting 333/066 MHz SDRAM up to 8GB Integrated Intel Gen 7 Graphics x HDMI_OUT port x HDMI_IN port LCD: Dual-Channels 24-bit LVDS x RS-232 port (Optional) x Mini-card socket x Realtek RTL8G Gigabit Ethernet controllers AMI 64Mb SPI Flash BIOS Realtek ALC662 + ALC3, Mic-in/Line-out 2 x Serial ATA ports with 300MB/s HDD transfer rate 7 x USB 2.0 ports 2 x USB 3.0/2.0 ports 9V DC Jack 0 ~ 60 C (32 ~ 40 F) w/ cooling fan 0 ~ 60% @ 60 C (non-condensing) Dimension (L xw) 70 x 70 mm (6.7 x 6.7 ) - 4 -
A Board Dimensions 59,84 54,94 22,86 0 0,6 63,83 57,48 52,6 30,04 0,3 92,96 74,9 58,47 26,48 4,7 0 6,7 57,48 0 59,84 54,94 53 BJ 8 (0,0) 58,47 74,9 92,97 0,49 30,05 4,7 26,49 6,7,67 52,6 Unit:mm - 5 -
Jumpers/Connectors Quick Reference Jumpers Label ❶ CLR_CMOS ❷ TXE_UNLOCK ❸ LCD_SEL Function Clear CMOS Setting TXE Unlock LCD Resolution Selection Connectors Label Function Label Function SYS_FAN 2COM Fan Power Connector Onboard serial port header (optional) 20 2SATA/2 22SATA_PWR Serial ATA 3.0 Gb/s connectors SATA power connector 3MINI_PCIE 4CPU_FAN 5SPEAKER 6DMIC 7F_AUDIO 8MIC 9LINE_OUT Mini PCI Express x slot (supports half-card) CPU Fan Power Connector Speaker Connector Digital Microphone header Front panel audio header Microphone Connector Line out Connector 23F_PANEL 24LVDS 25LVDS_BRT 26DIMM 27CIR Front panel switch/led header LVDS connector Display brightness header 204-pin DDR3 SDRAM SO-DIMM Consumer Infrared header (optional) 0DC_IN DC IN Power Connectors LAN Ethernet Connectors 2USB3_0 USB 3.0 Connector 3USB2_0 USB 2.0 Connector 4HDMI_OUT HDMI Output Connector 5HDMI_IN HDMI Input Connector 678 TC/CM/CR 5-pin USB 2.0 header supports one USB 2.0 Device 9F_USB Front panel USB 2.0 header - 6 -
Jumpers & Connectors Locations ➌LCD_SEL 24 LVDS 25 LVDS_BRT 26 DIMM 27 CIR ➊CLR_CMOS SYS_FAN 2COM 23 F_PANEL ➋TXE_UNLOCK 22 SATA_PWR 2SATA2 20SATA 3MINI_PCIE 4CPU-FAN 9F_USB 5SPEAKER 8CR 7CM 6TC 6DMIC 7F_AUDIO 5HDMI_IN 3USB2_0 0DC_IN 8MIC 4HDMI_OUT 2USB3_0 LAN 9LINE_OUT - 7 -
Jumpers Jumper Settings The jumper is short (closed) when the jumper cap is placed on pins. If not, that means the jumper is open. Connectors SYS_FAN: Fan Power Connector Connector Type: 2.54mm pitch x4-pin headers. Pin Description Pin open Pin short (closed) Pin 2-3 short (closed) ❶CLR_CMOS: Clear CMOS Setting Connector type: 2.54mm pitch x3-pin headers. Pin -2 short (closed) GND 2 +2V 3 FAN_Detect 4 Control 4 Pin Mode -2 Keep CMOS (Default) 2-3 Clear CMOS 3 2 3 2 ❷TXE_UNLOCK: TXE Unlock (Optional) Connector type: 2.54mm pitch x3-pin headers. Pin Mode -2 Normal (Default) 2-3 Override 2 3 2 3 2COM: Onboard serial port header (Optional) Connect a serial port extension bracket to this header to add a serial port to your system. Connector Type: 2.54mm pitch 2x5-pin headers. Pin Desc. Pin Desc. DCD 2 SIN 3 SOUT 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 2 0 9 RI 0 N/C ❸LCD_SEL: LCD Resolution Selection When your panel connects to LVDS, please check LCD Select header setting first. Connector type: 2.54mm pitch 2x4-pin headers. 3MINI_PCIE: Mini PCI Express x slot Connector type: Onboard 0.8mm-pitch 52-pin edge card connector Pin Voltage 2 2-2 5-6 600 x 900 7 8 7 5 6 8 2-2 3-4 920 x 080 (Default) 7 8 5 52-8 -
4CPU_FAN: CPU Cooling FAN Connector Connector Type: 2.54mm pitch x4-pin headers. Pin GND 2 +2V Description 3 FAN_Detect 4 Control 4 89MIC&LINE_OUT: Microphone&Line-out LINEOUT 0DC_IN: DC jack Connector type: DC Φ7.4 Male connector MIC 5SPEAKER: Internal Speaker Header Connector Type: 2.00mm pitch x4-pin headers. Pin Description L_Channel- 2 L_Channel+ 3 R_Channel+ 4 R_Channel- 6DMIC: Digital MIC Header Connector Type: 2.54mm pitch x5-pin headers. 4 Inner Shell :9V DC Outer Shell :GND LAN: Ethernet Connectors 8 Pin Description +3.3V 2 DMIC DATA 3 GND 4 DMIC Clock 5 N/C 5 3USB3_0: USB 3.0 Connector 7F_AUDIO: Front Panel Audio Header The front panel audio header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. This header supports HD audio by default. Connector Type: 2.54mm pitch 2x5-pin headers. Pin Desc. Pin Desc. 3USB2_0: USB 2.0 Connector FP_MIC_in 2 Analog_GND 3 MIC_Power 4 Presence# 5 FP_Right 6 Sense_Return 7 Sense_Send 8 N/C 9 FP_Left 0 Sense2_Return 9 2 0-9 -
4HDMI_OUT: HDMI Output Connector Connect the display device to the HDMI_OUT port 20 2SATA&2: Serial ATA Connectors 9 8 2 5HDMI_IN: HDMI Input Connector Connect other HDMI source to the HDMI_IN port 678TC/CM/CR: 5-pin USB 2.0 header Connector Type: 2.54mm pitch x5-pin headers. Pin Description +5V 2 USB- 3 USB+ 4 GND 5 N/C 9F_USB: 0-pin USB 2.0 header supports card reader and camera or other USB 2.0 devices Connector Type: 2.54mm pitch 2x5-pin headers. Pin Description Pin Description +5V 2 +5V 2 3 USB Port A (-) 4 USB Port B (-) 5 USB Port A (+) 6 USB Port B (+) 7 GND 8 GND 9 0 9 N/C 0 N/C 9 8 2 5 22SATA_PWR: Serial ATA Power Connector 23F_PANEL:Front panel switch/led header A standard set of switch and LED headers for ATX or Micro ATX cases Connector Type: 2.54mm pitch 2x5-pin headers. Pin Description PinDescription HD LED(+) 2 MSG LED (+) 3 HD LED(-) 4 MSG LED (-) 5 Reset Switch (-) 6 Power Switch (+) 7 Reset Switch (+) 8 Power Switch (-) 9 Reserved 0 N/C 9 2 0-0 -
24LVDS:LVDS Connector (40-Pin) Connector Type: 0.5mm pitch 40-pin coaxial connector Pin Assignment Pin Assignment ODD Lane3 + 2 NC 2 ODD Lane3-22 Power +3.3V 3 ODD Lane2 + 23 GND 4 ODD Lane2-24 GND 5 ODD Lane + 25 GND 40 6 ODD Lane - 26 ODD_Clock + 7 ODD Lane0 + 27 ODD_Clock - 8 ODD Lane0-28 GND 9 EVEN Lane3 + 29 GND 0 EVEN Lane3-30 GND EVEN Lane2 + 3 EDlD Clock 2 EVEN Lane2-32 LCD Backlight ON/OFF 3 EVEN Lane + 33 LCD Backlight adjustment 4 EVEN Lane - 34 EVEN Clock + 5 EVEN Lane0 + 35 EVEN Clock - 6 EVEN Lane0-36 LCD Backlight power +9V 7 GND 37 LCD Backlight power +9V 8 Power +5V 38 LCD Backlight power +9V 9 Power +5V 39 NC 20 Power +5V 40 EDlD Data - -
25LVDS_BRT:Display brightness header Connector Type: 2.00mm pitch x8-pin box headers. Pin Description LCD BKL ON/OFF 2 LCD BKL adjustment 3 LCD BKL Power +9V 4 LCD BKL Power +9V 5 GND 6 GND 8 7 LCD BKL Increase 8 LCD BKL decrease 26DIMM: SO-DIMM Connector 27CIR: Consumer Infrared Header Connector Type: 2.54mm pitch 2x4-pin headers. Pin Desc. Pin Desc. GND 2 N/C 3 N/C 4 N/C 5 PWR +5V 6 PWR +5V 7 CIR RX 8 N/C 7 2 8-2 -