Safety Precautions Thank you for purchasing MD100G Series Extension I/O. SAFETY PRECAUTIONS Always follow safety instructions to prevent accidents and potential hazards from occurring. Safety precautions are classified into WARNING and CAUTION and their meanings are as follows: WARNING Improper operation may result in serious personal injury or death. CAUTION Improper operation may result in slight to medium personal injury or property damage The indicated illustrations on the product and in the manual have the following meanings. Danger may be present. Read the message and follow the instructions carefully. Particular attention should be paid because danger of an electric shock may be present. Keep operating instructions handy for quick reference. Read the operating instructions carefully to fully understand the functions of the MD100G series and to use it properly. CAUTION Be cautious, when handling the CMOS components of the communication module. Static may lead to malfunctioning of the product. Turn off the inverter power, when changing the communication cable. Otherwise, you may damage the module or a communication error may occur. Make sure to insert the Option board connector to the inverter precisely. Otherwise, you may damage the module or a communication error may occur. Check the parameter unit before setting up the parameter. Otherwise, a communication error may occur. I
Table of Contents Table of Contents... 1... 1... 1... 2... 2... 3... 4... 4... 6... 8... 11... 11... 11... 11... 17... 18... 18... 20... 20... 23... 24... 25... 28... 29... 30 A terminal setting (On)... 30... 32... 32... 33... 37... 40... 45... 49... 53... 57... 61... 63... 65... 70... 72... 74... 90... 90... 91 ii
Chapter 1. Basic Information & Precautions 1
Chapter 2. Specifications 2
Chapter 2. Specifications 3
Chapter 3. Installation In case of. (2) (1) (3) (4) (5) 4
Chapter 3. Installation (7) (6) (8) (9) (10) (11) 5
Chapter 3. Installation 6
Chapter 3. Installation NPN Mode (Sink) 7
Chapter 3. Installation PNP Mode (Source) 8
Chapter 3. Installation Preinsulated Crimp Terminal Connectors (Bootlace Ferrule). 9
Chapter 3. Installation Note 10
Chapter 4. Basic Features 11
Chapter 4. Basic Features Set the Frq (Frequency reference source) code in the Operation group to 13 (V3), and then set code 02 (V3 Polarity) to 0 (unipolar) in the AO group. Use a voltage output from an external source or use the voltage output from the VR terminal(standard I/O) to provide inputs to V3. Refer to the diagrams below for the wiring required for each application. 010000 0.0010.00 0.00100.00 0.00 12.00 12
Chapter 4. Basic Features 13
Chapter 4. Basic Features 14
Chapter 4. Basic Features 15
Chapter 4. Basic Features 16
Chapter 4. Basic Features 17
Chapter 4. Basic Features 18
Chapter 4. Basic Features 19
Chapter 4. Basic Features 20
Chapter 4. Basic Features 21
Chapter 4. Basic Features 22
Chapter 4. Basic Features 23
Chapter 4. Basic Features * Displayed as on keypad. On the 7-seg screen of multi-function output contact parameter, clicking of left/right key switches between extension I/O and built-in I/O 7-seg screen. is extension I/O 7-seg screen. 24
Chapter 4. Basic Features Multi-step operations can be carried out by assigning different speeds (or frequencies) to the Px terminals. Step 0 uses the frequency reference source set with the Frq code in the Operation group. Px terminal parameter values 7 (Speed-L), 8 (Speed-M) and 9 (Speed-H) are recognized as binary commands and work in combination with Fx or Rx run commands. The inverter operates according to the frequencies set with St.13 (multi-step frequency 13), ba.5356 (multi-step frequency 47) and the binary command combinations. 25
Chapter 4. Basic Features Configure multi-step frequency 47. 26
Chapter 4. Basic Features 27
Chapter 4. Basic Features 28
Chapter 4. Basic Features 29
Chapter 4. Basic Features * Displayed as on the keypad. On the 7-seg screen of multi-function input state/contact parameter, clicking of left/right key switches between extension I/O and built-in I/O 7-seg screen. is extension I/O 7-seg screen. 30
Chapter 4. Basic Features 31
32
33
34
4 35
36
37
38
10 39
40
15 Displayed when Ad. 08 is set to 1 (DC-Brake). 41
42
43
0h1350 0h1351 0h1352 22 44
23 24 45
46
47
31 48
49
50
51
SW1(NPN/PNP) SW2(V1/V2[I2]) status 52
53
54
55
56
42 57
58
59
60
61
62
코드통신번지명칭표시설정범위초기값속성참조 63
코드통신번지명칭표시설정범위초기값속성참조 50 0을설정하면 Quantizing 사용하지않습니다. 51 0을설정하면 Quantizing 사용하지않습니다. 64
코드통신번지명칭표시설정범위초기값속성참조 65
66
67
CAP mode diagnosis 55 68
56 69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
단자대 90
91
92
93
Warranty Warranty Maker Model No. Customer Information Sales Office (Distributor) Regal Australia MD100G Extension I/O Name Address Tel. Name Address Tel. Installation Date Warranty Period Warranty period is 12 months from date of sale, subject to Regal Australia standard terms and conditions of sale. IN-WARRANTY service information If the defective part has been identified under normal and proper use within the guarantee term, contact your local authorized MD distributor or MD Service center. OUT-OF WARRANTY service information The guarantee will not apply in the following cases, even if the guarantee term has not expired. Damage was caused by misuse, negligence or accident. Damage was caused by abnormal voltage and peripheral devices malfunction (failure). Damage was caused by an earthquake, fire, flooding, lightning, or other natural calamities. When MD nameplate is not attached. When the warranty period has expired. A
IOM_MarathonDrive_MD100G_ExtensionI/OOptionManual_0415