Lexium 05 motion control

Similar documents
LXM32AD18N4 motion servo drive - Lexium 32 - three-phase supply voltage 208/480V kw

SD328AU68S2 motion control stepper motor drive - SD328 - <= 6.8 A

LXM32SD18M2 motion servo drive - Lexium 32-single phase supply voltage 115/230V - 0.5/1.kW

LXM28AU07M3X motion servo drive - Lexium 28 - single and three phase V W

ATV61HU55M3 ATV61 5,5 kw 7,5HP 240V single phase EMC IP20

ATV61HC11N4 SPEED DRIVE 150 HP 460 V ATV61

ATV61HC31Y variable speed drive ATV61-310kW - 690V - without EMC filter

ATV930U30M3 variable speed drive - ATV930-3kW - 200/240Vwith braking unit - IP21

ATV71QC16N4 variable speed drive ATV71Q - 160kW / 250HP V - IP20

ATV61QC31N4 variable speed drive ATV61Q - 315kW / 500HP V - IP20

ATV320U04N4C variable speed drive ATV kW V - 3 phase - compact

ATV320D11N4B variable speed drive ATV320-11kW V - 3 phase - book

ATV320D15N4B variable speed drive ATV320-15kW V - 3 phase - book

ATV320D15N4B variable speed drive ATV320-15kW V - 3 phase - book

ATV320U30N4B variable speed drive ATV320-3kW V - 3 phase - book

ATV32HU11M2437 variable speed drive ATV32-1.1kW 200V - 1P - Bluetooth built-in - w heat sink

ATV71EXA2C71N4 enclosed variable speed drive ATV71 Plus kw - 400V - IP23

ATV320U07M2C variable speed drive ATV kW V - 1 phase - compact

ATV340D75N4E variable speed drive - 75kW- 400V - 3 phases - ATV340 Ethernet

ATV61HC31N4 variable speed drive ATV61-315kW 500HP - 500V - EMC filter - IP20

ATV630U15N4 variable speed drive ATV kW/2HP V - IP21/UL type 1

ATV61HD11Y variable speed drive ATV61-11kW / 690V - 10HP / 575V - IP20

ATV32HU75N4 variable speed drive ATV kw V - 3 phase - with heat sink

ATV340D18N4E variable speed drive - 18kW- 400V - 3 phases - ATV340 Ethernet

ATV61HC22N4 Altivar 61 drive 350hp 400/480 3ph

ATV930D22M3 variable speed drive - ATV930-22kW - 200/240V- with braking unit - IP21

ATV320U06N4C variable speed drive ATV kW V - 3 phase - compact

TM241C40U controller M IO transistor NPN

ATV650U30N4E variable speed drive ATV650-3kW V - IP55 - disconnect switch

TM241C24T controller M IO transistor PNP

Variable speed drives for asynchronous motors Altivar 61 Option: Controller Inside programmable card

ATV32H075M2 variable speed drive ATV32-0,75 kw V - 1 phase - with heat sink

ATV32HU30N4 variable speed drive ATV32-3 kw V - 3 phase - with heat sink

ATV12P037F1 variable speed drive ATV kW hp V - 1ph - on base plate

ATV12P075M3 variable speed drive ATV kW - 1hp V - 3ph - on base plate

ATV12H018M2 variable speed drive ATV kW hp V - 1ph

ATV32HD11N4 variable speed drive ATV32-11 kw V - 3 phase - with heat sink

TM221M16TG controller M IO transistor PNP spring

ATV32HD11N4 variable speed drive ATV32-11 kw V - 3 phase - with heat sink

TM241CE24U controller M IO transistor NPN Ethernet

TM241CE24T controller M IO transistor PNP Ethernet

ATV32H055N4 variable speed drive ATV kw V - 3 phase - with heat sink

ATV12HU22M3 variable speed drive ATV12-2.2kW - 3hp V - 3ph - with heat sink

ATV310H075N4E variable speed drive ATV kw - 1 hp V - 3 phase

ATV12H075M3 variable speed drive ATV kW - 1hp V - 3ph - with heat sink

TM241CE24T controller M IO transistor PNP Ethernet

TM241CE40T controller M IO transistor PNP Ethernet

ATV310HU30N4E variable speed drive ATV310-3 kw - 4 hp V - 3 phase

ATV212WU40N4 variable speed drive ATV212-4kW - 5hp - 480V - 3ph - EMC class C2 - IP55

ATV32HU30N4 variable speed drive ATV32-3 kw V - 3 phase

TM241C40R controller M IO relay

ATV930U07M3 variable speed drive - ATV930-0,75kW - 200/240V- with braking unit - IP21

ATV32HU40N4 variable speed drive ATV32-4 kw V - 3 phase - with heat sink

XPSMF35. Product data sheet Characteristics. Preventa safety PLC compact - Profibus DP protocol. Main. Complementary. Safety module name

TM221M32TK controller M IO transistor PNP

Variable speed drives Altivar 71

ATV32H018M2 variable speed drive ATV32-0,18 kw V - 1 phase - with heat sink

ATV630D15N4 variable speed drive ATV630-15kW/20HP V - IP21/UL type 1

ATV212WU55N4 variable speed drive ATV kW - 7.5hp - 480V - 3ph - EMC class C2 - IP55

ATV650D22N4 variable speed drive ATV650-22kW/30HP V - IP55

TM241CE40R controller M IO relay Ethernet

TM241CEC24R controller M IO relay Ethernet CAN master

ATV630D11N4 variable speed drive ATV630-11kW/15HP V - IP21/UL type 1

TM241CE40R controller M IO relay Ethernet

ATV212WD30N4 variable speed drive ATV212-30kW - 40hp - 480V - 3ph - EMC class C2 - IP55

HMISBC Rear Module controller panel - Dig 8 inputs/8 outputs +Ana 4 In/2 Out

ATV32HU30N4 variable speed drive ATV32-3 kw V - 3 phase - with heat sink

ATV630D90N4 variable speed drive ATV630-90kW/125HP V - IP21/UL type 1

TM241CE40R controller M IO relay Ethernet

ATV212HD18N4 variable speed drive ATV kW - 25hp - 480V - 3ph - EMC - IP21

TM241CEC24T. Main. 14 (remote I/O architecture) W with max number of I/O expansion module ma fast input. 2.

Zelio Control-modular measurement and control relays 1

ATV340U15N4 variable speed drive - 1.5kW- 400V - 3 phases - ATV340

Variable speed drives Altivar 71

ATV71HC40N4 variable speed drive ATV71-400kW-600HP - 480V - EMC filter-graphic terminal

OTB1S0DM9LP I/O distributed module OTB - Modbus non isolated serial link m

ACOPOSinverter P74. User's Manual. Version: 2.20 (August 2016) Model no.: Original instruction

ATV212HD11N4 variable speed drive ATV212-11kW - 15hp - 480V - 3ph - EMC - IP21

ATV320U04N4C variable speed drive ATV kW V - 3 phase - compact

TM241CE24T controller M IO transistor PNP Ethernet

ATV930U55N4 variable speed drive - ATV930-5,5kW - 400/480V - with braking unit - IP21

OTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP m

ATV71HC50Y variable speed drive ATV71-500kW - 690V

TM221ME16T controller M IO transistor PNP Ethernet

ATV212HD15N4 variable speed drive ATV212-15kW - 20hp - 480V - 3ph - EMC - IP21

TM221ME32TK controller M IO transistor PNP Ethernet

TM221CE40T controller M IO transistor PNP Ethernet

Variable speed drives Altivar 61

5 MICROMASTER 440 specifications

ATV212HU55N4 variable speed drive ATV kW - 7.5hp - 480V - 3ph - EMC - IP21

TM221CE24T controller M IO transistor PNP Ethernet

ATV61HC80Y variable speed drive ATV61-800kW / 690V - 800HP / 575V - IP20

ILBPB24DO32. Inline Block IO Module for PROFIBUS With 32 Digital Outputs. AUTOMATIONWORX Data Sheet 6889_en_04. Description

XPSMF40. Main. Safety module name. Monitoring safety detection discrete input Monitoring safety dialogue discrete output

HMISCU6B5 3 5 color touch controller panel - Dig 8 inputs/8 outputs +Ana 4 In/2 Out

600 hp at V 3 phases. 568 A for 480 V 3 phases 400 kw / 600 hp 637 A for 380 V 3 phases 355 kw 709 A for 380 V 3 phases 400 kw / 600 hp

ATV212HU55N4 variable speed drive ATV kW - 7.5hp - 480V - 3ph - EMC - IP21

ATS22D88S6U. ATS22D88S6U soft starter-ats22-control110v-power 208V(25hp)/230V(30hp)/460V(60hp)/575V(75hp) Product data sheet Characteristics.

TM221ME16T controller M IO transistor PNP Ethernet

OTB1S0DM9LP I/O distributed module OTB - Modbus non isolated serial link m

Transcription:

Characteristics Environmental characteristics Conformity to standards have been developed to conform to the strictest international standards and the recommendations relating to electrical industrial control equipment (IEC, EN), including: low voltage, IEC/EN 61800-5-1, IEC/EN 50178, IEC/EN 61800-3 (conducted and radiated EMC immunity and emissions). EMC immunity IEC/EN 61800-3, environments 1 and 2 IEC/EN 61000-4-2 level 3 IEC/EN 61000-4-3 level 3 IEC/EN 61000-4-4 level 4 IEC/EN 61000-4-5 level 3 Conducted and radiated EMC emissions for servo drives IEC/EN 61800-3, environments 1 and 2, categories C2, C3 EN 55011 class A group 2, IEC/EN 61800-3 category C3 With additional EMC fi lter (1): b EN 55011 class A group 1, IEC/EN 61800-3 category C2 b EN 55011 class A group 2, IEC/EN 61800-3 category C3 With additional EMC fi lter (1): b EN 55011 class A group 1, IEC/EN 61800-3 category C2 b EN 55011 class A group 2, IEC/EN 61800-3 category C3 e marking Product certification The servo drives are e marked in accordance with the European low voltage (2006/95/EC) and EMC (89/336/EEC) directives. UL (USA), cul (Canada) Degree of protection IEC/EN 61800-5-1, IEC/EN 60529 Vibration resistance Shock resistance Maximum ambient pollution Environmental conditions Relative humidity Ambient air temperature around the device of cooling IP 41 on the upper part with protective cover in place IP 20 after removal of the protective cover, see page 61070-EN/2 According to IEC/EN 60068-2-6: 1.5 mm peak to peak from 3 Hz to 13 Hz 1 gn from 13 Hz to 150 Hz According to IEC/EN 61131 paragraph 6.3.5.2 15 gn for 11 ms conforming to IEC/EN 60028-2-27 Degree 2 conforming to IEC/EN 61800-5-1 IEC 60721-3-3 category 3C1 According to IEC 60721-3-3, category 3K3, 5% to 93%, without condensation Operation C 0 + 50 Temperature derating and limitations: see mounting recommendations page 61070- EN/2 Storage C - 25 + 70 LXM 05pD10F1 LXM 05CU70M2, pd10m2 LXM 05pD10M3X LXM 05pD17F1, pd28f1 LXM 05pD17M2, pd28m2 LXM 05pD17M3X, pd42m3x Natural convection Maximum operating altitude m 1000 without derating Up to 2000 under the following conditions: b Temperature 40 C max. b Mounting distance between servo drives > 50 mm b Protective cover removed Operating position Maximum permanent angle in relation to the normal vertical mounting position 10 10 Fan (1) See table on page 61065-EN/3 to check permitted cable lengths. 2 version: 2.1 61062-EN.indd

Drive characteristics Switching frequency khz 4 or 8 depending on rating and associated servo motor. See pages 61841-EN/2 and 61851-EN/2 Electrical power characteristics Power supply Voltages V 100-15%...120 + 10% single-phase for 200-15%...240 + 10% single-phase for 200-15%...240 + 10% three-phase for 380-15%...480 + 10% three-phase for Frequency Hz 50-5%...60 + 5% Transient overvoltage Overvoltage category III Inrush current A < 60 Leakage current ma < 30 External 24 V c power supply (not provided) (1) Signalling Output voltage Electrical isolation Input voltage V 24 (-15/+20%) Input current (no-load) A 1 Ripple y 5% 1 red LED: LED lit indicates the presence of servo drive voltage Maximum three-phase voltage equal to line supply voltage Between power and control (inputs, outputs, power supplies) Connection cable characteristics Recommended cable type for mounting in an enclosure Single-strand IEC cable, ambient temperature 45 C, copper 90 C XLPE/EPR or copper 70 C PVC Connection characteristics (terminals for the power supply, the DC bus, and the servo motor) Servo drive terminals R/L1, S/L2, T/L3 (power supply) PA/+, PBI, PBe (external braking resistor) U/T1, V/T2, W/T3 (servo motor) Maximum wire size and tightening torque for the power supply, braking resistor, DC bus and servo motor. LXM 05pD10F1 LXM 05CU70M2, pd10m2 LXM 05pD10M3X LXM 05pD17F1, pd28f1 LXM 05pD17M2, pd28m2 LXM 05pD17M3X, pd42m3x LXM 05pD14N4, pd34n4 2.5 mm 2 (AWG 14) 0.8 Nm 6.0 mm 2 (AWG 10) 1.2 Nm LXM 05pD57N4 16.0 mm 2 (AWG 6) 2.2 Nm 2.5 mm 2 (AWG 14) 0.8 Nm 6.0 mm 2 (AWG 10) 1.2 Nm 16.0 mm 2 (AWG 6) 2.2 Nm See characteristics of VW3 M5 10p Rppp and VW3 M5 30p Rpppp cables on pages 61841- EN/18 and 61851-EN/27 (1) Please consult our specialist catalogue "Phaseo power supplies and transformers". 61062-EN.indd version: 2.1 3

Control signal characteristics of servo drive LXM 05Apppppp LXM 05Bpppppp LXM 05Cppppp Protection Inputs Against reverse polarity Outputs Against short circuits Electrical link Presence of an electrical link on the 0 V c 24 V c I/O logic Positive logic (Sink input/source output) or negative logic (Source input/sink output). Positive logic is default setting. Logic inputs 24 V c logic inputs with positive (Sink) or negative (Source) logic Number 6, of which 3 are reassignable, see page 61068-EN/14 Power supply V c 24 4 6, of which 5 are reassignable, see page 61068-EN/16 Sampling period ms 0.25 Debounce filtering ms 1 Positive logic (Sink) Negative logic (Source) Safety inputs State 0 if < 5 V or input not wired, state 1 if > 15 V Logic inputs conforming to standard IEC/EN 61131-2 type 1 State 0 if > 19 V or input not wired, state 1 if < 9 V Inputs for the Power Removal safety function Number 2 (PWRR_A, PWRR_B) Power supply V c 24 Input filtering ms 1 Response time ms y 10 Positive logic (Sink) Logic outputs State 0 if < 5 V or input not wired, state 1 if > 15 V Logic inputs conforming to standard IEC/EN 61131-2 type 1 24 V c logic outputs with positive (Source) or negative (Sink) logic. Number 2, reassignable, see page 61068-EN/14 Output voltage V y 30, conforming to standard IEC/EN 61131-2 Sampling period ms 1 2 3, reassignable, see page 61068-EN/16 Max. breaking current ma 50 Voltage drop V 1 (at 50 ma load) Analog inputs ±10 V differential analog inputs Resolution bit 14 Number 2 (ANA 1+/ANA 1, ANA 2+/ANA 2 ) Input resistance kω u 10 1 (ANA 1+/ANA 1 ) Sampling period μs 250 Absolute error Less than ±1% at 25 C, less than ±2% over the operating temperature range Linearity Less than ±0.5% 4 version: 2.1 61062-EN.indd

Control signal characteristics (continued) of servo drive LXM 05Apppppp LXM 05Bpppppp LXM 05Cppppp Pulse/direction (P/D), A/B, CW/CCW signals RS 422 link Number 1 interface for P/D, A/B, CW/CCW signals Common mode range V - 7 + 12 1 interface for P/D, A/B signals 2 interfaces for P/D, A/B, CW/CCW signals Input resistance kω 5 Signal input frequency Pulse/direction (P/D) khz y 400 A/B khz y 400 CW/CCW khz y 400 y 400 ESIM (Encoder SIMulation) output signals Logic level RS 422 link Output frequency khz y 400 Servo motor encoder feedback signals Voltages Encoder power supply V + 10/100 ma SinCos input signals V 1 V SS with 2.5 V offset 0.5 V SS at 100 khz Input resistance Ω 120 Operational safety characteristics of servo drive LXM 05Apppppp LXM 05Bpppppp LXM 05Cppppp Protection Of the machine Power Removal (PWR) safety function which forces stopping and/or prevents unintended restarting of the servo motor, conforming to standard ISO 13849-1, performance level d (PL d), and standard IEC/EN 61800-5-2 Of the system process Power Removal (PWR) safety function which forces stopping and/or prevents unintended restarting of the servo motor, conforming to standard IEC/EN 61508 level SIL2 and standard IEC/EN 61800-5-2 61062-EN.indd version: 2.1 5

Communication port characteristics CANopen and CANopen Motionbus protocols (only applies to LXM 05Apppppp servo drives) Protocol type CANopen CANopen Motionbus Structure Connectors RJ45 (labelled CN4) or spring terminals (labelled CN1) Network management Transmission speed Address (Node ID) Polarization Slave Transmission speed depends on the length of the bus: b 50 kbps for bus lengths of up to 1000 m b 125 kbps for bus lengths of up to 500 m b 250 kbps for bus lengths of up to 250 m b 500 kbps for bus lengths of up to 100 m b 1 Mbps for bus lengths of up to 4 m, where no segment is no longer than 0.3 m 1 to 127, confi gurable via the display terminal or the PowerSuite software workshop Line termination impedances are integrated in the servo drive and are switchable. Service PDO (Process Data Objects) Implicit exchange of PDO: b 3 PDO conforming to DSP 402 modes (position control and speed profi le modes) b 1 confi gurable mapping PDO PDO modes Event-triggered, Time-triggered, Remotelyrequested, Sync (cyclic) Sync (cyclic), Sync (acyclic) PDO mapping 1 confi gurable PDO Implicit exchange of PDO: b 2 PDO conforming to DSP 402 (position control mode) Number of SDO (Service Data Objects) Emergency Explicit exchange of SDO: b 2 receive SDO b 2 transmit SDO Yes Explicit exchange of SDO: b 1 receive SDO b 1 transmit SDO Profi le Communication monitoring CiA DSP 402: CANopen Device Profile Drives and Motion Control Position control and speed profi le modes Position control mode Node guarding, heartbeat Diagnostics Using LEDs 2 LEDs: RUN and ERROR on integrated 7-segment display terminal Display of faults Full diagnostics with the PowerSuite software workshop Description file Modbus protocol (LXM 05Apppppp, LXM 05Bpppppp, LXM 05Cppppp servo drives) Structure Connector RJ45 (labelled CN4) A single eds file for the whole range is supplied on the documentation CD-ROM. This fi le contains the description of the servo drive parameters Physical interface Transmission mode Transmission speed Format Polarization Number of servo drives Address 2-wire RS 485 multidrop RTU Confi gurable via the display terminal or the PowerSuite software workshop: 9600 bps, 19.2 kbps or 38.4 kbps for serial links of up to 400 m Confi gurable via the display terminal or the PowerSuite software workshop: b 8 bits, odd parity, 1 stop b 8 bits, even parity, 1 stop b 8 bits, no parity, 1 stop b 8 bits, no parity, 2 stop No polarization impedances These must be provided by the wiring system (for example, in the master) 31 maximum 1 to 247, confi gurable via the display terminal or the PowerSuite software workshop Services Messaging Read Holding Registers (03) 63 words maximum Write Single Register (06) Write Multiple Registers (16) 61 words maximum Read/Write Multiple Registers (23) 63/59 words maximum Read Device Identifi cation (43) Diagnostics (08) Communication monitoring Monitoring function (node guarding) can be activated Time out can be set between 0.1 s and 10 s Diagnostics Display of faults on integrated 7-segment display terminal 6 version: 2.1 61062-EN.indd

Communication port characteristics (continued) PROFIBUS DP protocol (only applies to LXM 05Bpppppp servo drives) Structure Connector Spring terminals (labelled CN1) Physical interface 2-wire RS 485 multidrop Transmission speed Transmission speed depends on the length of the bus: b 9.6 kbps, 19.2 kbps, 45.45 kbps, 93.75 kbps for bus lengths of up to 1200 m b 187.5 kbps for bus lengths of up to 1000 m b 500 kbps for bus lengths of up to 400 m b 1.5 Mbps for bus lengths of up to 200 m b 3 Mbps, 6 Mbps, 12 Mbps for bus lengths of up to 100 m Address 1 to 126, configurable via the integrated 7-segment display terminal or the PowerSuite software workshop Services Periodic variables PPO type 2 8 PKW bytes 12 Process Data bytes Communication monitoring Can be inhibited Time out can be set via the PROFIBUS DP bus confi gurator Diagnostics Description file Two LEDs: RUN and ERR Display of faults on integrated 7-segment display terminal Full diagnostics with the PowerSuite software workshop A single gsd fi le for the whole range is supplied on the documentation CD-ROM. This fi le does not contain the description of the servo drive parameters 61062-EN.indd version: 2.1 7