PL - W0420 Quick Start Guide EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. WiFi HD Wi-Fi camera with temperature & humidity detection
Basic introduction Structure: Connection diagram: Tip: open a router can be normally connected to internet. All devices can be connected to each other through this router. 3 Whenever and wherever possible through the platform to view video and management Ulife cloud services platform 1 2 3 6 7 8 9 Packing list: 5 4 1 Microphone 2 Photosensitive lamp 3 lens 4 Antenna 5 Temperature and humidity sensor 6 System indicator 7 Alarm indicator 8 WIFI indicator 9 Status indicator Power adapter LAN wire Bracket Wall plug Screws The pictures are for reference only, please refer to real subjects. Features: 1 Connect WiFi 1 download software LAN 2 Wireless AP Wired network WLAN INTERNET Built-in professional image sensor, 1.3mega pixel HD IP camera Temperature and humidity detection Powerful Ulife cloud platform for remote surveillance on multiple mobile platforms (iphone, ipad, Android and PC) 720P+VGA dual streaming and other 6 optional stream combinations Remote Pan/Tilt rotate (Horizontal: 270 O / Vertical: 60 O ) Infrared LED, digital smart zoom Support both WiFi AP mode and client mode, can be used for family monitoring with your smartphone Account and password access, privacy secured IR-cut filter embedded 01 02
Specification: Items Imaging Sensor Viewing Angle Night Vision Distance Minimum illumination Frame Rate Video Resolution Video Compression Format Audio Compression Format Power Supply Power Consumption Micro SD cord Remote Pan/Tilt rotate Temperature and Humidity measurement accuracy Operating Temperature Operating Humidity Dimensions( D x W x H ) Approx. Weight Parameter 1/4-inch color CMOS 53 o (Horizontal) 5m 2Lux; 0Lux (IR ON) 30fps (720P/D1) 1280 x 720 (720P); 640 x 480 (VGA) H.264 ACC DC 5V/2A 3.6W (Max.) Supports to 32GB Horizontal: 270 O / Vertical: 60 O +/-10% 0 o C~45 o C 20~80%RH 110 x 108 x 135(mm) 470g The PC Client Installation Steps: 1. Install the U-life software. Download U-life software from www.ulifecam.com. Double-click the software icon in PC, Open and run software. 2. Register a account. If the first use, Click New Wizard to register a account, If register is successful, It will appear below interface. As shown: The PC Client Installation Preparation: Users using this product must have access to internet. Otherwise, you can not use this product through Internet. PC can be normally connected to internet through router. Close the windows firewall in PC. Download the U-life software from www.ulifecam.com. Before using this product, you must register a U-life account first. Before registering an account, you must ensure that the PC can access to internet, otherwise you can not register successfully. 03 04
3. Installation camera. As below shown: 4. View video and operation. After installation successfully, the pop-up list, The new added camerawill display in the list. Click to view video. The network view, in the My s list, double-click the corresponding camera. You can view the image through the remote network monitoring platform. The local view, in the Local s list, double-click the corresponding camera. You can view the image through the local area network monitoring. 1. Use network cable to connect the camera to the router. Network cable Router 2. Connect the power adapter to the camera, and insert the power source. Pay attention to the camera reset before installation. Reset method: power-on state press and hold the RESET button for 6 seconds. Power adapter Power source Reset * Regarding the equipment video settings and other settings, the user can according to the actual environment make flexible use, this is no longer about, Specific reference to "the UlifeCam manual (the fifth part - Advanced settings and FAQ)". 3. Add a camera to the U-life platform (i.e. you registered account). The Intelligent Mobile Client Installation Preparation: Select the camera serial number from the list and enter. Note: 16 ID serial number may be found at the bottom of the camera. Users using this product must have access to internet. Otherwise, you can not use this product through Internet. Before using this product, you must register a U-life Pro account first. Before registering an account, you must ensure that the mobile can access to internet, otherwise you can not register successfully. For iphone/ipad users, please search U-life Pro keyword on Apple APP Store. For Android users, please search U-life Pro keyword on GOOGLE PLAY Store. Select a cable to router Note:when you are connected to the router through the WiFi, please select WiFi to the router. * The intelligent mobile device terminal of Android system is similar to the intelligent mobile device terminal of Apple ios system and the APP installation procedures. please follow the following procedures to install: Note: Waiting for about 2 minutes, when the status indicator light, is said to have been properly connected to the platform. 05 PL -W0420 06 PL -W0420
The iphone Client Installation Steps: 1. Download and install the U-life Pro software. Open the App Store in the iphone mobile, then search U-life Pro keyword and install the U-life Pro software. As shown below: 3. Installation camera. The camera has two modes to connect to the U-life Pro platform, The user can select any one mode connection. Installation method are introduced as follows: The first WiFi connection mode: 1) Connect the power adapter to the camera, and insert the power source. Pay attention to the camera reset before installation. Reset method: power-on state press and hold the RESET button for 6 seconds. Power adapter Power source Reset 2. Register a account. Open the U-life Pro software, Click Register, If register i successful, It will appear My list interface. As below shown: Note: Waiting for about 2 minutes, when the status indicator light, is said to have been properly connected to the platform. 2) Connect the iphone mobile to the camera. Select the wireless network of the camera ID and connect. Note: 16 ID serial number may be found at the bottom of the camera. 07 08
3) Add a camera in the "My list": The second network cable connection mode: 1. Use network cable to connect the camera to the router. And the mobile phone is also connected to wireless network of the router. Network cable Router Note: 16 ID serial number may be found at the bottom of the camera. 2. Connect the power adapter to the camera, and insert the power source. Pay attention to the camera reset before installation. Reset method: power-on state press and hold the RESET button for 6 seconds. Input SSID and password. Note: SSID is the router wireless network name. Power adapter Power source Reset Note: Waiting for about 2 minutes, when the status indicator light, is said to have been properly connected to the platform. 09 10
3. Add a camera in the "My list": Note: 16 ID serial number may be found at the bottom of the camera. 4. View video and operation. After installation successfully, return to My list. The new added camera will display in the list. Click to view video. 11