MH-3621-U3 Clone
CONTENTS ABOUT THE DOCKING SYSTEM... 2 HARD DRIVE INSTALLATION GUIDE... 5 CLONE OPERATION GUIDE... 6 NOTE... 8 LIMITED WARRANTY... 10 1
Thank you for purchasing MH-3621-U3 from archgon. To ensure trouble-free use and prolong the life of your device, please read following instructions and note all precautions. About the Docking System Box Contents - MH-3621-U3 - USB 3.0 cable - AC Adaptor - User Manual Features USB 3.0 SuperSpeed transfer rate (backward compatible with USB 2.0) Compatible with 2.5 & 3.5 SATA HDD/SSD Enhanced Offline Clone Function LED power/activity indicator Plug & Play Tool free Specification Interface:SATA to USB 3.0 Material:Aluminum + Plastic Dimension:108 x 62 x 149 mm Weight:410 g OS Compatibility:Windows XP or above Mac OS 10.5 or above 2
Front View Blue: USB Link Orange: 0~24.99% clone completion Clone button Rear View Blue: Power Orange: 25~49.99% clone completion Red: standby Blue: HDD1 Orange: 50~74.99% clone completion Blue: HDD2 Orange: 75~100% clone completion Red: clone error USB3.0 DC IN Power Switch 3
Top View HDD 1 HDD 2 HDD Ejection Jacks for HDD1 and HDD2 4
Hard Drive Installation Guide STEP1: Target the correct location of SATA connector(s) STEP2: Install either 2.5 and/or 3.5 HDD/SSD(s) to the docking system and connect to the SATA connector(s) well. 5
Clone Operation Guide NOTE: All existed data on HDD2 will be deleted once clone operation starts. HDD combination can be of either or both 2.5 and/or 3.5 SATA HDDs, as long as the capacity of HDD2 is equal to or greater than HDD1. STEP 1: Install at least two HDDs into the docking system STEP 2: Make sure power is turned on and USB cable is NOT connected. 6
STEP 3: Press & hold the clone button for at least 5 seconds, then clone operation will start by indicating all 4 LEDs in orange. STEP 4: LEDs will then proceed to flash sequentially indicating the Clone is in progress. Each orange LED refers to every 25% of clone completion. It is only when every 25% of HDD1 is cloned to HDD2 that such LED will remain constantly on, leaving the other LED(s) in running stage. When Clone operation is fully completed, all LEDs will flash regularly in orange. NOTICE: Any time clone operation fails, LED on HDD2 flares in red, leaving the other LEDs off. Refer to Section 4.4 & 4.5 in Normal & Clone Mode Table Chart under Diagnosis of LED in below NOTE session for details. 7
Note Clone Function All data on HDD2 will be deleted once clone operation starts. The capacity of HDD2 must be equal to or greater than HDD1. If the capacity of HDD2 is greater than HDD1, the remained capacity in HDD2 upon clone completion can be formulated to a new partition. Power synchronization feature This device detects PC power status and turn on & off itself automatically. When PC is off or hibernates, HDD(s) spin down and all LEDs off, except that Power LED remains constantly on in red until main power is shut down. a. In some OS, when system reaches sleep mode, only monitor and peripheral are turned off while motherboard is powered on. In this case, HDD and LED will be still on. b. To enhance smart power synchronization, do not turn off main power of this device. Use this device Upon PC connection, this device operates by Normal mode (port multiplier). 2 separate volumes will be recognized. Either 1 or 2 HDDs can be used at the same time. To operate Clone function, 2 HDD/SSDs are required. Removing HDD during clone operation is forbidden. This will result in failure and stoppage of the operation. HDD Support Installing HDD(s) with more than 2TB is possible. However, make sure to run this device under Vista, Win7 & 8 OS and activate GPT mode when formatting this device to have it work correctly. The motor of hard drive will not immediately stop running after power being turned off. Therefore, it is highly recommended that to turn off the power first and then wait for 20 seconds before hard drive removal. It is safer operational procedure. USB Connectivity The equipped USB3.0 port is downward compatible with USB2.0 PC/notebook by simply plug and play. 8
SATA Connectivity This device supports HDD hot swapping. The following procedure must be fully acknowledged before practice. a. Hot swapping during HDD(s) operation may result in wreckage of such HDD. (e.g. disk plate scratched, leading to HDD malfunctioning.) b. Removing any HDD will result in re-detection of both or connected HDD by OS. In the meantime, file transferring in progress will be forced to stop, leading to file(s) corruption. In conclusion, to prevent the above damage, it is strongly recommended that the device must be power off and HDD(s) have come to a full stop before removing. Diagnosis of LEDs This device consists of 4 LEDs The chart below describes LED activity under various conditions. R: Read W: Write S3: PC into sleep mode S4: PC into hibernation mode Normal & Clone Mode Table Chart Configurations Operation O operation PWR USB HDD1 HDD2 PC Clone button HDD status Activities LED Status HDD1 HDD2 Link Power HDD1 HDD2 1 Power OFF 2 Power ON Red 3 Normal mode No USB cable connected 3.1 3.2 3.3 No USB connected HDD1 inserted No USB connected HDD2 inserted No USB connected Both HDDs inserted OFF Red OFF Red OFF OFF Red 4 Clone operation-no USB cable connected 4.1 4.2 4.3 4.4 4.5 Both HDDs inserted Clone started Clone Operation In progress Clone Operation Complete Clone Operation Cannot start Or HDD1 > HDD2 ON ON 25% 50% 75% 100% Orange Orange Orange Orange R W ON ON Orange running back & forth OFF OFF OFF OFF Orange flash Orange flash Orange flash Orange Clone Operation Failed OFF OFF Red flash Red flash 9
5 Normal mode- USB cable connected 5.1 USB connected No HDD Blue Blue 5.2 USB connected HDD1 inserted R/W ON Blue Blue Blue flash 5.3 USB connected HDD2 inserted R/W ON Blue Blue Blue flash 5.4 USB connected Both HDDs inserted R/W R/W ON ON Blue Blue Blue flash Blue flash 6 Power synchronization mode -Power saving 6.1 PC enters Standby, Hibernate mode S3,S4 OFF OFF Red 6.2 PC Power OFF OFF OFF OFF Red 6.3 USB Cable Removed OFF OFF Red Limited Warranty Archgon warrants MH-3621-U3 is free from defects in materials or workmanship under normal use for a period of one (1) year from the date of original purchase. The limited warranty does not cover upon occurrence of the following events 1. Damages from misuse, accident or any man-caused damages 2. The disassembly or the re-equipping causes the damage arbitrarily. 3. Improper maintenance, leading to product failure or damage 4. Unsuitable physical or operating environment beyond product specification, leading to product failure or damage. * For further questions, please write an e-mail to archgon@archgon.com 10
內容 關於產品... 12 硬碟安裝說明... 15 CLONE 操作說明... 16 注意事項... 18 有限保固... 20 11
感謝您購買亞齊慷雙插槽 SATA 硬碟外接座 MH-3621-U3 為確保產品使用流暢並延長 裝置的使用壽命, 請您使用前詳細閱讀以下說明並留意注意事項 關於產品 包裝內容物 - MH-3621-U3 雙插槽 SATA 硬碟外接座 - USB 3.0 傳輸線 - AC 電源轉接器 - 說明書 產品特色 USB 3.0 高速傳輸效率 ( 向下支援 USB 2.0) 支援 2.5 吋 & 3.5 吋 SATA 硬碟 支援硬碟 Clone 功能 LED 電源 / 狀態指示燈 即插即用 免工具安裝 產品規格 產品介面 :SATA to USB 3.0 材質 : 陽極鋁合金 + 塑膠尺寸 :108 x 62 x 149 mm 重量 :410 g 作業系統 :Windows XP 或以上 Mac OS 10.5 或以上 12
正面 藍燈 : USB Link 橘燈 : 0~24.99% clone 複製完成 Clone 按鍵 背面 藍燈 : Power 橘燈 : 25~49.99% clone 複製完成紅燈 : 待機 藍燈 : HDD1 橘燈 : 50~74.99% clone 複製完成 藍燈 : HDD2 橘燈 : 75~100% clone 複製完成紅燈 : clone 複製失敗 USB3.0 DC 輸入 電源開關 13
上面 HDD 1 HDD 1 & HDD 2 移除硬碟按鍵 HDD 2 14
硬碟安裝說明 STEP1: 確認 SATA 介面的正確位置 STEP2: 裝入 2.5 吋或 3.5 吋硬碟, 並確認硬碟有穩固安裝於外接座上 15
Clone 操作說明 注意 : 一旦 Clone 複製作業開始, 所有在 HDD2 的資料將被刪除 請確認 HDD2 內無重要資料或已妥善備份 執行 Clone 作業的硬碟組合可以是 2.5 吋或 3.5 吋硬碟, 但 HDD2 的硬碟容量 ( 目的地硬碟 ) 必須大於或等於 HDD1 硬碟容量 ( 來源硬碟 ) STEP 1: 裝入至少兩顆硬碟, 並確認硬碟有穩固安裝於外接座上 STEP 2: 確認裝置電源在開啟狀態, 並確認 USB 傳輸線已移除 16
STEP 3: 按住 Clone 按鍵不放約 5 秒, 當 4 個 LED 燈亮橘燈即表示 clone 複製作業即 將開始 STEP 4: Clone 複製期間,LED 燈會持續依跑馬燈形式來回亮起 每一個橘色 LED 燈代表 25% clone 複製作業完成, 只有在 HDD1 每完成 25% 硬碟複製到 HDD2 的作業時, 代表的 LED 燈才會維持燈亮狀態, 其餘的 LED 燈仍維持跑馬燈來回亮燈的形式 當 clone 複製作業完成, 所有 LED 燈會一起呈現規律地閃爍狀態 注意 : 在操作期間若 clone 複製作業失敗,HDD2 的 LED 燈會亮起紅燈, 其他的 LED 燈 會熄滅, 請參照注意事項底下 LED 參考表格第 4.4 & 4.5 說明 17
注意事項 Clone 硬碟複製功能 一旦 Clone 複製作業開始, 所有在 HDD2 的資料將被刪除 請確認 HDD2 內無重要資料或已妥善備份 執行 Clone 作業的硬碟組合可以是 2.5 吋或 3.5 吋硬碟, 但 HDD2 的硬碟容量 ( 目的地硬碟 ) 必須大於或等於 HDD1 硬碟容量 ( 來源硬碟 ) 若 HDD2 硬碟容量大於 HDD1, 在 clone 作業完成後, 剩餘的硬碟容量可格式化為一個新的磁區 省電模式 此裝置會偵測電腦電源自動進入省電模式 當電腦關機或進入休眠狀態, 硬碟會怠速且只有 power 指示燈會亮紅燈, 其他 LED 燈會熄滅 a. 在某些作業系統, 當系統進入休眠狀態時, 僅有螢幕會關閉, 主機板仍在運作狀態, 在這種情形下, 裝置的 LED 燈並不會熄滅 b. 為執行智慧型省電模式, 請勿關閉此裝置的主要電源 裝置使用 若裝置與電腦連接, 即與一般外接座無異, 硬碟作為外接式硬碟使用 若同時安裝 2 顆硬碟則視為 2 個獨立的儲存裝置 若要執行 clone 硬碟複製作業, 必需安裝兩顆硬碟 在 clone 複製作業期間請勿移除任何硬碟, 否則會造成硬碟複製作業失敗, 也有可能造成資料上的遺失 支援硬碟 本裝置支援容量 2TB 以上之硬碟, 但請確保電腦系統為 Vista, Win7 & 8 OS 以上且利用 GPT 模式格式化硬碟, 以確保硬碟操作正常 硬碟馬達在關閉裝置電源後並不會立即停止運作, 強烈建議在關閉裝置電源後, 在移除硬碟前靜待約 20 秒, 待硬碟馬達完全停止運作後再安全移除硬碟 18
連接 SATA 介面 此裝置支援硬碟熱插拔, 但在執行硬碟熱插拔前, 請確認以下需知 a. 若在硬碟操作期間拔除硬碟可能會導致硬碟損壞 ( 例如 : 硬碟磁盤刮傷導致硬碟 機能失常故障 ) b. 拔除硬碟會使系統重新辨識此裝置, 所以若安裝 2 顆硬碟, 在其中一顆硬碟執行 任務時拔除另一顆硬碟也會導致系統重新辨識外接式裝置, 會導致硬碟執行任務 強迫終止並有可能導致資料損毀 為避免以上情形發生, 強烈建議請務必確認裝置電源關閉且硬碟運作完全停止後, 再 進行拔除硬碟的動作 LED 狀態顯示 本裝置裝配 4 個 LED 燈 以下表格顯示 LED 燈在不同作業底下所顯示的狀態 R: 硬碟讀取資料 W: 硬碟寫入資料 S: 電腦進入休眠模式 一般使用模式 & 硬碟複製模式 LED 狀態表 操作 1 電源關閉 配置 操作 電源 USB HDD1 HDD2 動作 PC Clone 硬碟狀態 LED 狀態按鍵 HDD1 HDD2 Link Power HDD1 HDD2 2 電源開啟 紅燈 3 一般模式 移除 USB 傳輸線 3.1 安裝 HDD1 OFF 紅燈 3.2 安裝 HDD2 OFF 紅燈 3.3 安裝雙硬碟 OFF OFF 紅燈 4 硬碟複製模式 移除 USB 傳輸線 4.1 安裝雙硬碟硬碟複製開始 ON ON 25% 50% 75% 100% 橘燈 橘燈 橘燈 橘燈 4.2 硬碟複製中 R W ON ON 橘燈以跑馬燈形式來回閃爍 4.3 硬碟複製完成 OFF OFF 橘燈閃爍 橘燈閃爍 橘燈閃爍 橘燈閃爍 19
4.4 硬碟複製程序無法開始或 HDD1 > HDD2 OFF OFF 紅燈閃爍 4.5 硬碟複製失敗 OFF OFF 紅燈 5 一般模式 連結 USB 傳輸線 5.1 無安裝硬碟 藍燈藍燈 5.2 安裝 HDD1 R/W ON 藍燈藍燈 藍燈閃爍 5.3 安裝 HDD2 R/W ON 藍燈 藍燈 5.4 安裝雙硬碟 R/W R/W ON ON 藍燈 藍燈 6 省電模式 6.1 電腦待機休眠 S OFF OFF 紅燈 6.2 電腦關機 OFF OFF OFF 紅燈 藍燈閃爍 藍燈閃爍 藍燈閃爍 6.3 移除 USB 傳輸線 OFF OFF 紅燈 有限保固 亞齊慷對全系列產品自原購買日起一年內 ( 若無購買證明則以本公司產品出廠序號日期為 準 ), 針對非人為因素所導致之故障瑕疵提供檢測維修服務 以下情形, 恕無法提供保固服務 a. 因濫用 意外或任何人為因素造成的產品損壞 b. 因天災等不可抗力之因素所造成的產品損壞 c. 因自行拆卸或改裝產品所造成的產品損壞 d. 因不當使用 不當維護或不當保養所造成的產品損壞 e. 超過產品容許範圍外的不良使用環境所導致的產品損壞 f. 產品序號汙損 標籤損毀 脫落或篡改 若您對亞齊慷產品有任何疑問, 請來信 product@archgon.com 20
www.archgon.com 21