echnical data sheet Damper actuator for Modbus for adjusting air dampers in ventilation and air conditioning systems in buildings orque 5 Nm Nominal voltage AC/DC 4V Communication via Modbus RU (RS-485) Conversion of sensor signals LM4A-MOD with cable LM4A-MOD-J6 with socket LM4A-MOD LM4A-MOD-J6 echnical data Electrical data Nominal voltage AC 4V, 50/60 Hz / DC 4V Nominal voltage range AC 9.... 8.8V / DC.6... 8.8V Power consumption In operation W @ nominal torque At rest. W For wire sizing.5 VA Connection LM4A-MOD LM4A-MOD-J6 Data for Modbus Protocol Number of nodes ransmission formats Baud rates Scheduling Parameterisation Cable m, 6 x 0.75 mm RJ socket Modbus RU (RS-485), not galvanically isolated Max. (without repeater) -8-N-, -8-N-, -8-E-, -8-O- Default: -8-N- (start bits, data bits, parity, stop bits) 9 600, 9 00, 8 400, 76 800, 5 00 Bd Default: 8 400 Bd 0, can be switched With the service tool ZH-GEN, push-button-operated fast addressing... 6 possible Functional data Factory settings Variable Setting orque (nominal torque) Min. 5 Nm @ nominal voltage 5%, 50%, 75% reduced... Position accuracy ±5% Direction of rotation As an option with switch 0 / Direction of motion at Y = 0% At switch position 0 or Electronically reversible... Manual override Gearing latch disengaged with push-button, can be locked Angle of rotation Max. 95, can be limited at both ends with adjustable mechanical end stops Running time 50 s / 90 5... 50 s... Automatic adjustment of running time, control and feedback to match the mechanical angle of rotation Override controls, controllable via Modbus Manual triggering of the adaption by pressing the «Adaption» button or with the PC tool MAX (maximum position) = 00% MIN (minimum position) = 0% Automatic adaption whenever the supply voltage is switched on, or manual triggering... MAX = (MIN 0 )... 00% MIN = 0%... (MAX 0 )... Sound power level max. 5 db(a) With a running time of 5 s = 45 db(a) 50 s = 5 db(a) Position indication mechanical, pluggable Safety Protection class Degree of protection EMC III Safety extra-low voltage IP54 in any mounting position (for LM4A-MOD-J6 only with extra protective sleeve) CE according to 004/08/EC. www.belimo.com - en v. 08.0 Subject to changes / 8
echnical data Safety notes (continued) Principle of operation ype (according to EN 6070-) Rated current voltage 0.8 kv (according to EN 6070-) Control pollution degree (according to EN 6070-) Ambient temperature 0... 50 C Non-operating temperature 40... 80 C Ambient humidity 95% r.h., non-condensing (according to EN 6070-) Maintenance Maintenance-free Dimensions / Weight Dimensions See «Dimensions» on page 8 Weight Approx. 560 g! he actuator must not be used outside the specified field of application, especially in aircraft or in any other airborne means of transport. It may only be installed by suitably trained personnel. Any legal regulations or regulations issued by authorities must be observed during installation. he device may only be opened at the manufacturer's site. It does not contain any parts that can be replaced or repaired by the user. he cable must not be removed from the device. When calculating the required torque, the specifications supplied by the damper manufacturers (cross-section, design, installation site), and the air flow conditions must be observed. he device contains electrical and electronic components and is not permitted to be disposed of as household refuse. All locally valid regulations and requirements must be observed. Product features Principle of operation Converter for sensors Parameterisable actuators Simple direct mounting Manual override Adjustable angle of rotation High operational reliability Home position he actuator is fitted with an integrated interface for Modbus RU, receives its digital positioning signal from the superordinate Modbus-Master and returns the current status. Connection option for a sensor (passive or active sensor or switching contact). In this way, the analogue sensor signal can be easily digitised and transferred to Modbus. he factory settings cover the most common applications. As desired, individual parameters can be adapted for specific systems or servicing with a service tool (e.g. ZH-GEN). he Modbus communication parameters (address, baud rate, ) are set with the ZH-GEN. Pressing push-button while connecting the supply voltage resets the communication parameters to the factory setting. Quick addressing: he Modbus address can alternatively be set using push-buttons from to 6. he value selected is added to the «Basic address» parameter and results in the effective Modbus address. For example, with a basic address of 40, Modbus addresses between 4 and 56 can be parameterised using quick addressing. Simple direct mounting on the damper spindle with a universal spindle clamp, supplied with an anti-rotation strap to prevent the actuator from rotating. Manual override with push-button possible (the gear is disengaged for as long as the button is pressed or remains locked). Adjustable angle of rotation with mechanical end stops. he actuator is overload-proof, requires no limit switches and automatically stops when the end stop is reached. When the supply voltage is switched on for the first time, i.e. at commissioning or after pressing the «gear disengagement» switch, the actuator travels to the home position. Pos. direction of rotation switch Home position 0 Y = 0 ccw Left stop Y = 0 cw Right stop he actuator then moves into the position defined by Modbus-Master. / 8 - en v. 08.0 Subject to changes www.belimo.com
Modbus overview Register No. Adr Register 0 Setpoint [%] Override control Command 4 Actuator type 5 4 Relative position [%] 6 5 Absolute position [ ] [mm] 7 6 Relative volumetric flow [%] (only for VAV/EPIV) 8 7 Absolute volumetric flow (pressure) [m /h] [l/min] [Pa] (only for VAV/EPIV) 9 8 Sensor value [mv] [Ω] [] 0 00 Series number st part 0 0 Series number nd part 0 0 Series number 4th part 04 0 Firmware version (Modbus module) 05 04 Malfunction and service information 06 05 Min [%] 07 06 Max [%] 08 07 Sensor type 09 08 Bus fail position In operation Service Registers in Bold can be written Registers <00 (In operation) which can be written are volatile and should therefore be updated periodically Registers >00 which can be written are non-volatile Commands Note regarding Read Discrete Inputs he command reads one or more bits and can alternatively be used for register 05 (Malfunction and service information). he start address to be used is 664. All data is arranged in a table and addressed by..n (register) or 0..n- (address). No distinction is made between data types (Discrete Inputs, Coils, Input Registers, Holding Registers). As a consequence, all data can be accessed with the two commands for Holding Register. he commands for Discrete Inputs and Input Registers can be used as an alternative. Standard commands: Read Holding Registers [] Write Single Register [6] Optional commands: Read Discrete Inputs [] Read Input Registers [4] Write Multiple Registers [6] www.belimo.com - en v. 08.0 Subject to changes / 8
Modbus register description Register : Setpoint Register : Override control Register : Command Register 4: Actuator type Register 5: Relative position Register 6: Absolute position Register 7: Relative volumetric flow Register 8: Absolute volumetric flow Setpoint for actuator setting or volumetric flow in hundredths of one percent, i.e. 0 0 000 corresponds to 0 00% Overriding the setpoint with defined values Override control 0 None Open Close Min 5 Max Initiation of actuator functions for service and test; the register is reset automatically. Command 0 None Adaption est run Synchronisation 4 Reset actuator malfunctions Actuator type; the allocation may deviate from the basic category with some actuators. Actuator type 0 Actuator not connected / not known Air/water actuators with/without safety function Volumetric flow controller VAV / EPIV Fire damper actuator Relative position in hundredths of one percent, i.e. 0 0 000 correspond to 0 00% Absolute position 0 0 000 (6555 if not supported by the actuator) he unit depends on the device: [ ] for actuators with rotary movement [mm] for actuators with linear movement Relative volumetric flow in hundredths of one percent of Vnom, i.e. 0 0 000 correspond to 0 00% his value is available only for VAV controllers and EPIV devices (actuator type: ). For all other types, 6555 will be entered. Absolute volumetric flow his value is available only for VAV controllers and EPIV devices (actuator type: ). For all other types, 6555 will be entered. he unit depends on the device: [m /h] for VAV controllers (or [Pa] for pressure applications) [l/min] for EPIV devices Register 9: Sensor value Current sensor value; dependent on the setting in Register 08 he unit depends on the sensor type: [mv] [Ω] [-] Register 0, 0: Series number Register 04: Firmware Version Each MP node has an unambiguous series number which is either impressed on or glued to the node. he series number consists of 4 segments, although only parts, and 4 are displayed on Modbus. Example: 0089-4-064-008 Register 9 Register 0 Register st part nd part 4th part 0089 4 008 Firmware version of Modbus module (VX.XX) e.g. 0 V.0 4 / 8 - en v. 08.0 Subject to changes www.belimo.com
Modbus register description Register 05: Malfunction and service information (continued) he status information is split into messages about the actuator (malfunctions) and other service information. Malfunctions (low byte) Service (high byte) Bit Description 0 Excessive utilisation Mechanical travel increased Mechanical overload 4 Safety-relevant faults (fire protection only) 5 Damper test error (fire protection only) 6 Duct temperature too high (fire protection only) 7 Smoke detector tripped (fire protection only) 8 Internal activity (test run, adaption, ) 9 Gear disengagement active 0 Bus watchdog triggered 4 5 he malfunction bits can be reset with Register (command 4) or with the Belimo PC-ool. Malfunctions 0 and 4 cannot be reset. Register 06: Min / Vmin setting Register 07: Max / Vmax setting Register 08: Sensor type Note After changing the sensor type, the actuator must always be restarted in order for correct sensor values to be read out. Register 09: Bus fail position Minimum limit (position or volumetric flow) in hundredths of one percent, i.e. 0 0 000 correspond to 0 00% Caution: Changing the setting may result in malfunctions. Maximum limit (position or volumetric flow) in hundredths of one percent, i.e. 000 0 000 correspond to 0 00% Caution: Changing the setting may result in malfunctions. Sensor type connected to the actuator; in the absence of sensor specification, the switching at the Y input will have the effect of a local compulsion. Sensor type 0 None Active sensor (mv) Passive sensor k (Ω) Passive sensor 0 k (Ω) 4 Switching contact (0 / ) Modbus communication is not monitored as standard. In the event of a breakdown in communication, the actuator retains the current setpoint. he bus monitoring controls the Modbus communication. If neither the setpoint (Register ) nor the override control (Register ) is renewed within 0 seconds, the actuator controls to the bus fail position (closed / open). riggered bus monitoring is indicated in Register 05. Bus fail position 0 Last setpoint (no bus monitoring) Fast close if time is exceeded Fast open if time is exceeded. www.belimo.com - en v. 08.0 Subject to changes 5 / 8
Electrical installation Connection diagram for cable layout Note Connection via safety isolating transformer.! Connection without sensor Note Modbus signal assignment: C = D = A C = D = B Power supply and communication are not galvanically isolated. Interconnect ground signal of the devices. MF D D Connection with passive sensor, e.g. Pt000, Ni000, NC MF D D Sensor emperature range Resistance range Resolution Ni000 8... 98 C 850... 600 P000 5... 55 C 850... 600 NC 0... 60 C (depending on type) 00... 50 k Connection with switching contact, e.g. p-monitor p Requirements for switching contact: he switching contact must be able to accurately switch a current of 6 ma at 4 V. MF D D Connection with active sensor, e.g. 0... 0 V @ 0... 50 C Possible input voltage range: 0... V (resolution 0 mv) MF D D 6 / 8 - en v. 08.0 Subject to changes www.belimo.com
Electrical installation Parameterisation RJ socket Notes Always fit feed pins in pairs! Only attach and remove connection cable when de-energised! (continued) Connection assignment: Pin : AC/DC 4V Pin : GND Pin : D (A) Pin 4: D (B) Pin 5: AC/DC 4V Pin 6: GND Modbus signal assignment: C = D = A C = D = B ZH-GEN AC 4 V DC 4 V ZH-GEN OK ZK-GEN MF D D PC tool Belimo PC-ool AC 4 V DC 4 V Note he actuator can be triggered with the PC tool under «PP». MF D D ZK-GEN Operating controls and indicators 4 5 Direction of rotation switch Switching over: Direction of rotation changes Push-button and LED display green Off: Illuminated: Flashing: Press button: Push-button and LED display yellow Off: Illuminated: Flickering: Press button: 4 Gear disengagement button Press button: Release button: No power supply or fault In operation Address mode: pulses according to set address (... 6) when starting: reset to factory setting (communication) in standard mode: switches on angle of rotation adaptation in address mode: confirmation of set address (... 6) he actuator is ready Adaption or synchronising process active or actuator in address mode (green LED indicator flashing) Modbus communication active in operation (> s): switch address mode on and off in address mode: address setting by pressing several times when starting (>5 s): reset to factory setting (communication) Gear disengaged, motor stops, manual override possible Gear engaged, synchronisation starts, followed by standard operation 5 Service plug For connecting parameterising and service tools www.belimo.com - en v. 08.0 Subject to changes 7 / 8
Dimensions [mm] Dimensional drawings 6 66 6 Damper spindle Length 7 6... 0 6 0 6 4 8 / 8 - en v. 08.0 Subject to changes www.belimo.com
787-0000.A 7 6... 0 6 0 4 8 0 mm 6 Nm mm 5 65 www.belimo.com M9- v.0 0.0 /
AC 4 V / DC 4 V MF D D Pin : AC/DC 4V Pin : GND Pin : D (A) Pin 4: D (B) Pin 5: AC/DC 4V Pin 6: GND AC 4 V / DC 4 V MF D D AC 4 V / DC 4 V p p MF D D AC 4 V / DC 4 V MF D D / M9- v.0 0.0 www.belimo.com