BATmode S / S+ QUICKSTART GUIDE Set Up and First Start Up Version: 0/9
SAFETY INSTRUCTIONS Please read these safety instruc ons carefully before startup your BATmode system! - Only use power supplies authorized by bat bioacous ctechnology.! - Avoid excessive mechanic strain on the BATmode system, especially on plugs and connectors if cables are connected to the BATmode or the antenna and microphone disc. Strong vibra ons, shaking or dropping may damage system parts. - Ensure a safe and stable moun ng of the BATmode and the corresponding discs. Dropping can harm persons, property or the BATmode system. - Ensure that nobody can stumble on installed and connected wires. Stumbling can harm persons and damage system parts. - Only use accessories supplied or authorized by bat bioacous ctechnology. The use of unauthorized accessories may damage the device. - Please contact our support if the BATmode system shows any damage or does not work properly. Do not open system parts and try to repair damage by yourself or through unauthorized personnel. This will cause the loss of warranty.
Table of Contents SAFETY INSTRUCTIONS... Learn about your device... 4 LED Status Indicators... 5 Antenna Disc and UltraSoundGate... 6 Microphones... 7 Connect... 0 Remote Access via WIFI... Remote Access via LAN... First Start Up... 4 Mobile Set Up... 6 Daily Status SMS...7 Remote SMS... 8 mybat... 0 Set Up... Installation...
Learn about your device 4 5 6 7 8 9 0 4 5 6 7 8 9 0 4 On-/Off-Switch Mobile Service LED Power LED Status LED WIFI-Hotspot LED (only BATmode S+) SIM-Card Slot (Mini-SIM) USB-Port for UltraSoundGate (monitored) UltraSoundGates Status LEDs USB-Port for UltraSoundGate (monitored) Temperature Sensor Input (only BATmode S+) Precipita on Sensor Input (only BATmode S+) Cellular Antenna Connector Kensington-Lock Power Supply HDMI Port LAN Connector USB.0-Ports e.g. for Backup-S ck HDMI Port Hea ng Output WIFI Antenna Connector (only BATmode S+) - Front View BATmode S/S+ - BATmode 4 5 6 7 8 9 0 S+ - Back View BATmode S/S+ - WIFI WWAN 4 5 6 7 8 9 0
LED Status Indicators How to interpret the LED status indicators of your BATmode S/S+ correctly: Power LED (white) On Device on Off Device off WIFI Hotspot LED (green-red) Status LED (blue-red) Off Blue BATcontrol not started Blue blinking Monitoring started Blue-red blinking Monitoring Start not possible Please control calibra on and UltraSoundGates Monitoring stopped, BATcontrol on Mobile Service LED (green) Green WIFI-Hotspot on On Mobile connec on connected Off WIFI-Hotspot off Single blinking Registered to mobile network Red Error - Please, check WIFI se ngs in Windows Double blinking SIM locked, SIM not recognized, no mobile service connec on UltraSoundGates Status LEDs (green) Number of illuminated LEDs = Number of available microphone channels 5
Antenna Disc and Magne c Base Antenna WIFI Antenna Connector Temperature Sensor Connector Cellular Antenna Connector The Antenna Disc contains a direc onal WIFI antenna. Since the direc on of the strongest signal is directed into the paper plane, the disc has to be installed with the illustrated connector side turned away from a poten al connec on partner. 4 Cellular Antenna Connector - Antenna Disc (only BATmode S+) - - Magne c Base Antenna (only BATmode S) - 4 6
UltraSoundGates 6Hnbm and 46Hnbm UltraSoundGate 6Hnbm UltraSoundGate 46Hnbm - Frontview - Backview - - Backview - + USB-.0 Interface + 4 Microphone XLR Connector 4 4 You can use an UltraSoundGate 6Hnbm for each microphone or one UltraSoundGate 46Hnbm for up to four microphones. BATmode S/S+ Systems can use up to four microphones simultaneously. 7
Microphones Microphone Disc GM50 Microphone XLR Connector (UltraSoundGate) Screws for removing the moun ng plate Reference Signal Speaker Connector (UltraSoundGate) 4 Microphone Capsule 5 Reference Signal Speaker - Front View - GM50 The Microphone Disc GM50 can either be used with the enclosed moun ng plate or with an op onal tripod. - Back View To connect the microphone and the reference signal speaker of the GM50 please use the Y-XLR microphone cable. 4 Be careful not to touch the microphone capsule and to protect it from moisture! 8 5
Microphone Disc GM90 Microphone XLR Connector (UltraSoundGate) Hea ng Connector Windscreen made of foam 4 Microphone Capsule 5 Reference Signal Speaker - Front View - Do not remove the windscreen foam, as this has an essen al influence on the calibra on of your microphone disc! To mount the GM90 in the floor of the nacelle a hole with a diameter of 00-05mm is required. - Back View - 4 5 Be careful not to touch the microphone capsule and to protect it from moisture! 9
Microphones Tower Microphone TM0 Microphone XLR Connector (UltraSoundGate) Op onally available movable tripod for tower wall moun ng Microphone Capsule For moun ng in non-magne c walls, please s ck the enclosed adhesive pads on the feet of the tripod. - Frontview The moun ng hole for the TM0 must have a minimum diameter of 4mm, as well as a maximum depth of 460mm. Be careful not to touch the microphone capsule and to protect it from moisture! 0
Tower Microphone TM0 Op onally available moun ng rod Microphone XLR Connector (UltraSoundGate) Op onally available movable tripod for tower wall moun ng Reference Signal Speaker Microphone Capsule 4 5 For moun ng in non-magne c walls, please s ck the enclosed adhesive pads on the feet of the tripod. The moun ng hole for the TM0 must have a minimum diameter of mm, as well as a maximum depth of 450mm. - Frontview - 4 5 Be careful not to touch the microphone capsule and to protect it from moisture!
Connect How to connect all components of your BATmode S+ System correctly: - BATmode S+ BATmode S+ WWAN - UltraSoundGate(s) - WIFI - Power Adapter - - Backup-S ck - - Keyboard / Mouse - - Microphone(s) - - Monitor(s) the4selected Depending on microphones, the hea ng can be omi ed - Antenna Disc - - Precipita on Sensor - Op onal and not included in delivery scope Please follow the manual of the precipita on sensor
How to connect all components of your BATmode S System correctly: - BATmode S BATmode S WWAN - UltraSoundGate(s) - - Power Adapter - - Backup-S ck - - Microphone(s) - - Keyboard / Mouse 44 selected Depending on the microphones, the hea ng can be omi ed - Magne c Base Antenna - - Monitor(s) - Op onal and not included in delivery scope
Remote Access via WIFI How to access your BATmode with your Windows running laptop via WIFI: Step Connect the WIFI of your Windows running laptop with the WIFI-Hotspot of the BATmode. Default SSID: BATmode Default Password: 45678" Step Open the Windows program Remote Desktop Connec on, insert the WIFI IP of your BATmode in Computer and press Connect. Default WIFI IP: 9.68.7. Step Insert the Username BAT and the Windows Password and press OK. Default Windows Password: 45 4 WIFI connec on is only available for BATmode S+.
Remote Access via LAN How to access your BATmode with your Windows running laptop via LAN: Step WWAN WIFI Use an Ethernet cable to connect the LAN port of your Windows running laptop (RJ45) with the one of the BATmode (RJ45). Step Open the Windows program Remote Desktop Connec on, insert batmode in Computer and press Connect. Step Insert the Username BAT and the Windows Password and press OK. Default Windows Password: 45 5
First Start Up Star ng of the BATmode System and the BATcontrol control so ware: Step Start the BATmode System. Step Use mouse, keyboard and monitor or connect your laptop via WIFI or LAN as described on page and. The control so ware BATcontrol starts automa cally. 4 4 5 6 Status Bar Task Bar for page choosing Selected Page Monitoring Start-/Stop-Bu on Message Bar 5
Star ng of the Aviso -RECORDER USGH recording so ware and the start of the acous c monitoring and data acquisi on of the external sensors: Step A er selec ng your se ngs on the different pages of BATcontrol, start the monitoring with a click on the Start-/Stop-Bu on. Step The recording so ware will open and the acous c monitoring as well as the simultaneous data acquis on of temperature and precipita on begin. Step To stop data acquisi on click on the Start-/Stop-Bu on or close the recording so ware. The external sensors for temperature and precipita on acquisi on are only available for BATmode S+. 7
Mobile Set Up How to set up your BATmode for SMS and mobile Internet connec on: Step Insert the Mini-SIM card in the SIM card slot (For this, the BATmode must be turned off). Step Use the Mobile se ngs in Windows to remove a possibly ac vated PIN from your SIM card. Step Insert the APN of your provider in the mobile se ngs of Windows. Step 4 Enter the number of the SMS center of your provider in SMSC-Number in BATcontrol. 8 An ac vated PIN will prevent the BATmode system to restore a mobile connec on a er a possible power failures, automa cally.
Daily Status SMS Se ngs in BATcontrol - Enable Daily Status SMS and insert the phone number of the receiver of the Daily Status SMS in Receiver Number(s). Use the interna onal format: e.g. +49598574. Use ; to separate mul ple receiver numbers. - Select the daily transmission me and the desired format. HRI: Values preceded by acronym. CSV: Values separated by commas. Meaning of the sent values and acronyms Acron. Meaning Acron. Meaning ID MON LRL LRD LFD FL4 ID of the BATmode Systems Current monitoring status FT FC FD SL WWW WIFI Total number of recordings Free space on C: in GB Free Space on D: in GB Current mobile signal level in % Status of the Internet connec on Status of the WIFI-Hotspot Last reference value Time of the last reference value Time of last recording Recordings in the last 4 hours 9
Remote SMS Se ngs in BATcontrol - Enable the SMS Remote checkbox. - Add the mobile number of the command sending device to the Security Number(s). Android-App Download from our webpage the free Android App BATconnect SMS for SMS remote control of your BATmode systems. Use these SMS commands to control your BATmode systems via text SMS Command System response Start monitoring! Start monitoring: :00-4:00! Start monitoring: :00-4:00 and 0:00-0:00! Start monitoring: -0/0! Monitoring will start ungated Monitoring will start from am to pm Monitoring will start from am to pm and 8 pm to am Monitoring will start from 0min before sunset to 0min a er sunrise Monitoring will stop Recording so ware RECORDER will be killed Stop monitoring! Kill Recorder! 0
Reboot! Shutdown! Send status! Send Mail! Send Mail to max(at)moritz.de Start WIFI-Hotspot! Stop WIFI-Hotspot! Connect WWAN! Disconnect WWAN! Kill Recorder! Reset USG! Send MAC! Send WIFI-IP! Send LAN-IP! Enable Status-Mail! Disable Status-Mail! Enable Status-SMS! Disable Status-SMS! System will reboot System will shut down System will send Status SMS System will send Status Mail Systen will send Status Mail to max@moritz.de WIFI-Hotspot will start WIFI-Hotspot will stop Mobile Connec on will be connected Mobile Connec on will be disconnected Recording so ware RECORDER will be killed System will reset UltraSoundGate System will send its MAC adress System will send its WIFI IP System will send its LAN IP Daily Status Mail will be enabled Daily Status Mail will be disabled Daily Status SMS will be enabled Daily Status SMS will be disabled
mybat Use the mybat cloud service to monitor your BATmode systems from anywhere in the world. Step Ac vate mybat in BATcontrol on your BATmode and choose a mybat password. Step Sign Up by using your Purchase-Code on: h ps://www.mybat.bioacous ctechnology.de Purchase-Code: Step Assign your BATmodes to your account by using the MAC addresses of your BATmode systems and the selected mybat password. Default mybat Password: 45678 mybat requires an ac ve Internet connec on via LAN or mobile connec on. MAC adress of this BATmode:
Set Up This checklist will help you to forget nothing, when se ng up your BATmode system: Insert SIM Card Configure SMS remote access Change Windows password in Windows Configure mybat Change Windows password in ChangeAutoLogonPassword Enter Recording Periods Insert APN Insert SMSC-Number Change WIFI-Hotspot SSID and password Change ID Configure daily reference signal Set microphone channel names Enter microphone calibra on values Connect Backup-S ck and configure Backup Configure daily Status SMS Install Teamviewer and set up a permanent password Configure daily Status Mail Configure GSM Switch Socket This checklist refers to a standard configura on of the BATmode system with GSM Switch Socket, which uses SMS, mobile Internet and WIFI as remote access op ons. For more detailed explana ons of the individual se ngs, please refere to the manual. WIFI is only available for BATmode S+ systems. Test all planned remote access paths before installa on in the wind turbine.
Installa on The following points should be clarified in advance of the installa on: Power supply Installa on loca on of the disc(s) Mobile coverage at the installa on site Installa on loca on of the BATmode/BATbox Internet via turbine network possible Cabling/cable length With this checkliste you only have to climb once in the nacelle of the turbine and have everything necessary with you. BATmode system (preferably in BATbox S) Microphone disc(s) Antenna disc/magne c base antenna All cables Extension cable for power supply Drill with a drill bit of 0 mm. mm metall drill bit for pre-drilling the fastenings of the discs at least six.5 mm SPAX screws with screwdriver to fix the discs Magne c feet or screws, pre-drill bit and screwdriver to fix the BATmode or BATbox Cabinet key Cable es Laptop with Ethernet cable Smartphone GSM Switch Socket Ethernet cable This checklist refers to a standard configura on of the BATmode system. 4
BATbox S Use the op onally available BATbox S for an easy and safe installa on of your BATmode S/S+ system. Your advantages - Safe protec on of your expensive measuring equipment. - Easy installa on of all components of your BATmode S/S+ system. - Thermal design for use in nacelles of wind turbines. - The compact size of the BATbox S allows to use the elevator to bring it in the nacelle. - Op onally available feet allow a drill free installa on in the nacelle of most wind turbines. Not included in the delivery scope of a BATmode system. Please refer to the manual of the BATbox S. 5
BATscreen The so ware tool for an efficient analysis of your recorded bat calls. Features - Fast visualiza on and audio playback of bat calls. - Easy check of automated call categoriza on. - Fast and efficient manual analysis of large amounts of data. - Data export for ProBAT. - Supports WAV and RAW files. - Graphical data analysis tools to determine temporal ac vity distribu on and correla ons with environmental parameters. - and much more. You will find the free func on-reduced trial version BATscreen LITE in the download area on our homepage: www.bioacous ctechnology.de/downloads Not included in the delivery scope of a BATmode system. Please refer to the manual of BATscreen. 6
- Graphical data analysis - - Call visualiza on and data categoriza on - 7
bat bioacoustictechnology GmbH Hohe Straße D-9060 Winkelhaid www.bioacoustictechnology.de info@bioacoustictechnology.de +49 (0) 5 / 98574 The detailed manual is always available on the Internet as up to date PDF download www.bioacoustictechnology.de/downloads 8 Product illustrations similar. Misprints, errors, innovations and changes reserved.