Professional Pan Tilt Zoom Camera ST-HD-PTZ-2MP INSTALLATION MANUAL www.nacebrands.com www.securitytronix.com
Description: The ST-HD-PTZ-2MP is a professional-grade intelligent dome color camera with Pan/Tilt/Zoom (PTZ) capabilities, and 1080p resolution. The camera is designed to function with HD-COAXINATOR recorders to utilize Control Over Coax (COC) without the need for an additional RS485 connection. Specifications: Image Sensor Resolution Scanning System Auto Electronic Shutter Minimum Illumination Signal to Noise Ratio Video Output Day/Night Backlight Compensation White Balance Gain Control Noise Reduction Lens 1/2.8 Exmor CMOS 1920(H) x 1080(V) @25fps Progressive 1/1 ~ 1/30,000s Color: 0.05Lux@F1.4; B/W: 0.005Lux@F1.4 > 50dB 1-channel BNC HDCVI high definition video output / CVBS standard definition video output (Can switch) Auto(ICR) / Color / B/W BLC / HLC / DWDR (Digital WDR) Auto, ATW, Indoor, Outdoor, Manual Auto / Manual 2D/3D 4.3mm - 129mm Pan/Tilt Range Pan: 0 ~ 360 endless / Tilt: -10 ~ 90, auto flip 180 Pan Speed Protocol Alarm Power Supply Power Consumption Working Environment Ingress Protection 350 /sec DH-SD, Pelco-P/D (Auto recognition) 2/1 channel In/Out AC 24V/1.5A 10.5W, 19W (Heater on) -30 f ~ 130 f / Less than 90% RH IP66 Dimensions Φ7.5 x 10 Weight 6lbs Default Address 1 Default Baud Rate 9600 CAUTION: To reduce the risk of electrical shock do not remove the cover or back of this unit. No user serviceable parts are inside. CAUTION: To prevent electric shocks and risk of fire hazards, do not use other than specified power source. 1
Unpacking Package Contents: (1) ST-HD-PTZ-2MP High-Speed Color Camera (1) Wall Mounting Bracket (1) 24V AC Power Supply (1) Installation Manual Ensure that all accessories and documentation are removed from the container before discarding packing material. Inspect the front, sides, and rear of the equipment for shipping damage. Make sure the equipment is clean, and no connectors are broken, damaged, or loose. If equipment appears to be damaged or defective please contact your distributor or SecurityTronix at: (800) 688-9282, press 3 for tech support, then press 2 for CCTV. Setup & Installation!! ATTENTION!! Be sure that all three screws that attach the camera to the mounting bracket are tightened securely. The installer must comply with electrical safety standards. There must be sufficient space between the camera s power supply and video line and any high voltage equipment and/or cables. To help ensure the camera s life and proper operation do not point the camera towards the sun or strong light. Do not install the camera in an environment where the temperature is above 130 f. Do not install the camera near a magnetic field or a highpower motor. Do not mount the camera near a radiator or heater. 2
The installation site and material must fully support the weight of the product. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe gently with a mild detergent. Never use strong or abrasive detergents. The included 24VAC power supply must be used. Using a DC or other incorrect power supply will damage the camera. Only qualified installers are allowed to install and test the camera. The camera is a low voltage product. If installed outdoors proper safety and lightning grounding are required. Be sure the grounding, wiring, input power, and voltage are correctly set prior to powering up and using. 3
Making Connections 1. Connect the AC power supply cable to the camera s power leads. 2. Connect the camera to the CVR with a 75Ω coaxial video cable. 3. (Optional) Connect unshielded twisted pair (UTP) control cable between the camera s labeled RS485 leads and the PTZ controller. Be sure wire polarities (+/-) are the same at each connection. 4. Connect power supply s AC plug to a suitable AC power outlet. Operation Setting Address Default Address: 1 Default Baud Rate: 9600 On your PTZ controller, CALL preset 95 to enter the OSD MENU. The symbol will indicate your current selection. Using the joystick or up/down arrows, navigate to SYSTEM SETTING and press OPEN to enter. 4
Navigate to ADDR INFORMATION and press OPEN to enter. Change ADDR TYPE to SOFT by moving left or right using your PTZ controller. Next, navigate to ADDR-SOFT and set your desired address by moving right to increase, or left to decrease. Once the desired address has been set, navigate to SAVE and press OPEN to save the address settings. Finally, navigate to EXIT and press OPEN on your PTZ controller to exit the OSD MENU. Basic Operation The table below is a quick guide to the camera s basic operations using a PTZ controller. Function Operation Pan/Tilt Move joystick or press arrows left, right, up, or down. Zoom Out Press WIDE or rotate the joystick counter-clockwise for the desired image. Zoom In Press TELE or rotate the joystick clockwise for the desired image. Focus Near Press NEAR until there is a clear image. Focus Far Press FAR until there is a clear image. Note: the camera will attempt auto-focus after being panned, tilted, or zoomed. Enter OSD Menu CALL Preset 95 Confirm Menu Selection Press OPEN Set Left Point WRITE Preset 92 Set Right Point WRITE Preset 93 Begin Left/Right Scan CALL Preset 99 End Left/Right Scan Move joystick or press arrows left, right, up, or down. 5
Setting a Tour After PRESET locations have been set, enter the OSD MENU, then use the joystick or up/down arrows to navigate to FUNCTION SETTING and press OPEN to enter. Next, navigate to TOUR and press OPEN. Using the controller s joystick or arrow buttons, move left or right at TOUR NO to select the desired tour to edit, then navigate to SETTING and press OPEN. Use the joystick or arrow buttons to navigate tour positions. Up and down will cycle through the positions currently displayed on screen, and left and right will cycle through pages of positions. Once a tour position is selected (indicated by the symbol), press OPEN to edit the tour position s parameters. Move the joystick left and right to choose which parameter to edit, or up and down to change parameter values. 6
PRESET indicates which preset number will be called for the tour position. DWELL indicates the amount of time the camera will spend at the tour position. SPEED indicates the speed that the camera will move to the next tour position. Press OPEN to return to position selection. Enter the parameters for desired tour positions in order starting at 1. Up to 32 tour positions may be assigned per tour. Any positions left with PRESET 000 will not be included in the tour. Once all desired tour positions have been configured. Navigate to BACK and press OPEN to return to the TOUR menu. To begin the tour: make sure that the desired TOUR NO is selected, then navigate to CALL, and press OPEN. The tour will begin, and no further steps are needed. The OSD menu will disappear from the screen after a few moments. To end a running tour: simply move the controller s joystick or directional buttons left, right, up, or down. Troubleshooting Issue Solution No picture after applying (1) Check that all plugs and cables are securely connected power. to the proper connectors. (2) Ensure that the power supply is providing the correct voltage and current. Picture is consistently (1) Check that the coaxial video cable from the camera to tinted or distorted. the CVR is securely connected at both ends. (2) Connect the camera to an alternate working coaxial video cable between the camera and CVR. (3) Re-terminate the coaxial video cable between the camera and CVR with new BNC connectors. Picture has ripples or (1) Check to see if the power supply is experiencing AC rolling lines. ripple; if so, a filter may be required. (2) Determine if the monitor is faulty. (3) Determine if other peripheral equipment is causing ripple, and if so, make the necessary adjustments. The picture is tinted / Fluorescent lights magnetic field may cause color roll. (1) 7
continuously changing Colors. Power and video are on, but the controller does not move the camera. Check that the coaxial video cable between the camera and CVR is not too close to fluorescent lights; increase distance as needed. (2) Reduce the number of fluorescent lights near the camera. (1) Check to ensure that the controller is set to the baud rate, address, and protocol of the camera. (2) Check to ensure that the RS485 connections at the camera and the PTZ controller have the same polarity. (3) Check the integrity and continuity of the unshielded twisted pair (UTP) control cable. For further assistance and troubleshooting, please contact SecurityTronix tech support at: (800) 688-9282, press 3 for Tech Support, then press 2 for CCTV. 8
9
10
11 Version 1.0 (3/25/15) 2015 North American Cable Equipment.