AIR HANDLING UNIT CONNCECTION VIA TL-WR802N (AHU, TL-WR802N, smartphone) QUICK LAUNCH GUIDE P0117_AZ_0001

WWW.SALDA.LT AIR HANDLING UNIT CONNCECTION VIA TL-WR802N (AHU, TL-WR802N, smartphone) QUICK LAUNCH GUIDE P0117_AZ_0001

CONTENTS I. CONNECTING THE ROUTER 3 II. TP-LINK WIRELESS N NANO ROUTER RANGE EXTENDER MODE CONFIGURATION VIA WIRELESS 3 II.I. QUICK INSTALLATION GUIDE 6 III. TP-LINK WIRELESS N NANO ROUTER ACCESS POINT MODE CON- FIGURATION VIA WIRELESS 21 III.I. QUICK INSTALLATION GUIDE 24

MB-GATEWAY I. CONNECTING THE ROUTER There are two types of router configurations: 1. TP-LINK Wireless N Nano router Range extender mode configuration via wireless TL-WR802N is used to extend the range of wireless signal of the existing AP or wireless router. On this mode, the wired port LAN/WAN works as LAN. MB-GATEWAY could connect to the control device by wireless way. 2. TP-LINK Wireless N Nano router Access point mode configuration via wireless As the supplement of wired LAN, TL-WR802N enables the wired LAN to connect to the MB-GATEWAY wirelessly. Connect TL-WR802N to the power and connect the LAN cable correctly with MB-GATEWAY, you can access MB-GATE- WAY by your PC(s), Mobile phone, Tabled and etc, to the router wirelessly. On this mode, the wired port LAN/WAN works as LAN. The Pre-encryption function is opened by default and the default password is the last unique eight numbers of each Router s MAC address. II. TP-LINK WIRELESS N NANO ROUTER RANGE EX- TENDER MODE CONFIGURATION VIA WIRELESS 1. Connect the router according to steps A to C in the diagram. Connect the LAN/ WAN port of TL-WR802N to the wired network port with an Ethernet cable to MB-GATEWAY and connect TL-WR802N to the power. TP-LINK router Internet The root AP s Wi-Fi name A TL-WR802N s Wi-Fi name: TP-LINK_XXXX Root AP Root router MB-Gateway B Figure 1.1 Hardware Installation of the TL-WR802N in Range Extender Mode The company reserves the right to make changes of technical data without prior notice 3

1. 2. Wait until the router boots up, about 30 second, then use the default Wi-Fi Name and Password printed on the Wi-Fi Info card to connect to the router Figure 2.1. Figure 2.1 Wi-Fi Info card LAPTOPS Click the icon at the bottom of your desktop. Click refresh button, and then select the default SSID of the Router. Click Connect Figure 2.2. Figure 2.2 Wi-Fi connection Enter the Security key from Wi-Fi Info card Figure 2.1. Click Next Figure 2.3. Figure 2.3 Security key window 4 The company reserves the right to make changes of technical data without prior notice

MOBILE PHONES, TABLETS Go to Wi-Fi settings. Click the button Scan and then select the default SSID of the Router. Figure 2.4. Figure 2.4 Wi-Fi connection Enter the Security key from Wi-Fi Info card. Figure 2.1. Click Connect. Figure 2.5. Figure 2.5 Security key window The company reserves the right to make changes of technical data without prior notice 5

II.I. QUICK INSTALLATION GUIDE With a Web-based utility, it is easy to configure and manage the TL-WR802N 300Mbps Wireless N Nano Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 1. To access the configuration utility, open a web-browser and type in the default address http://tplinkwifi.net in the address field of the browser. After a moment, a login window will appear, similar to the one in Figure 1.1. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key. admin admin Figure 1.1 Login window 2. After a successful login, you can click the Quick Setup menu to quickly configure your Router. Figure 2.1 Quick Setup 3. Click Next, and then Working Mode page will appear (figure 2.1) and choose Range Extender Mode and click Next on Working Mode page (Figure 3.1). 6 The company reserves the right to make changes of technical data without prior notice

Figure 3.1 Working Mode page 4. AP list page will appear as shown in Figure 4.1. Find the SSID of the Access Point you want to access, and select the Choose checkbox in the corresponding row. For example, the first item is selected. The target network s SSID will be automatically filled into the corresponding box which is shown in the Figure 4.1. Figure 4.1 AP List The company reserves the right to make changes of technical data without prior notice 7

5. Wireless Setting page will appear. Enter the ROOT AP Wireless password and select radio button Copy from Root AP, then click Next as shown in Figure Figure 5.1 Quick Setup - Wireless Wireless Name of Root AP The SSID of AP that you want to access. MAC Address of Root AP The MAC address of AP that you want to access. WDS Mode In WDS Repeater mode, the AP with WDS enabled will transfer data to an associated root AP. AP function is enabled meanwhile. The wireless repeater transfers signal between its stations and the root AP for greater wireless range. Enter the MAC address of the root AP in the field MAC Address of Root AP. Wireless Security Mode This option should be chosen according to the security configuration of the AP you want to access. It is recommended that the security type is the same as your AP s security type. Root AP Wireless Password If the AP your router is going to connect need password, you need to fill the password in this blank. Wireles name of Range Extender Select same like roo ap name. NOTE: If you know the SSID of a desired AP, you can also enter it into the SSID field manually. 8 The company reserves the right to make changes of technical data without prior notice

6. On this page you can configure the IP parameters of the LAN. If you are not familiar with the setting on this page, it is strongly recommended to keep the provided default values, otherwise wireless network performance may be poor. When you have finished, click the button Next, as it is shown in Figure 6.1. Figure 6.1 Quick Setup Network Settings 7. You will then see the Finish page. Figure 7.1. To finnish configuration click Reboot. Figure 7.1 Quick Setup - Finish The company reserves the right to make changes of technical data without prior notice 9

MB-GATEWAY NOTE: The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For the best results, the place your Router should be placed: Near the center of the area in which your wireless stations will operate. In an elevated location such as a high shelf. Away from the potential sources of interference, such as PCs, microwaves, and cordless phones. Away from large metal surfaces. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. After reboot connect the LAN/WAN port of TL-WR802N (A in Figure 8.1) to the wired network port with an Ethernet cable to MB-GATEWAY (B in Figure 8.1) and connect MB-GATEWAY to ventialtion system (C in Figure 8.1). Internet The root AP s Wi-Fi name A TL-WR802N s Wi-Fi name: TP-LINK_XXXX Root AP Root router C MB-Gateway B TP-LINK router Figure 8.1 Hardware Installation of the TL-WR802N and MB-GATEWAY in Range Extender Mode 8. Select new access point. LAPTOPS Click the icon at the bottom of your desktop. Click refresh button, and then select SSID of the Router, which you write enter in Wireless Name of Range Extender field. Figure 5.1. Click Connect like in figure 9.1. Figure 9.1 Wi-Fi connection 10 The company reserves the right to make changes of technical data without prior notice

Enter the Security key, which you write in Root AP Wireless Password field in figure 5.1. Click Next. Figure 9.2 Security key window MOBILE PHONES, TABLETS Go to Wi-Fi settings. Click button Scan and then select SSID of the Router, which you entered in Wireless Name of Range Extender field. Figure 5.1. Figure 9.3 Wi-Fi connection Enter the Security key in Root AP Wireless Password field. Figure 5.1.Click Connect in Figure 9.4 Figure 9.4. Security key window The company reserves the right to make changes of technical data without prior notice 11

9. To access MB-GATEWAY, open a web-browser (Google Chrome is recommended) in address field type the MB-GATEWAY device name (hostname). According to the factory settings (default) MB-GATEWAY device name MBGW - plus the last six MAC address characters, for example: mbgw900154. In the page enter the login data: according to the preset parameters (default) username: admin password: admin. 10. Control MB-GATEWAY via SALDA AIR android application. Install SALDA AIR to mobile phone. Go to Google play store. In the Search field enter SALDA AIR. Figure 10.1 Google play store application In the search results list find the application SALDA AIR. Click on the application. Figure 10.2 Figure 10.2 SALDA AIR application 12 The company reserves the right to make changes of technical data without prior notice

Click the button INSTALL. Figure 10.3 Figure 10.3 Install SALDA AIR application window. In the window that appears click ACCEPT and SALDA AIR will be installed on your device. Figure 10.4 Figure 10.4 Install SALDA AIR application window The company reserves the right to make changes of technical data without prior notice 13

11. Start AIR SALDA Wireless configuration. Go to Wi-Fi settings. Click button scan, then select SSID of the Router and enter it in the field Wireless Name of Range Extender. Figure 5.1. Figure 11.1 Security key window Enter the Security key in the field Root AP Wireless Password. Figure 5.1. Click Connect. Figure 11.2. Figure 11.2. Security key window 14 The company reserves the right to make changes of technical data without prior notice

Start SALDA AIR on Android and CONNECTING window will appear, as shown in Figure 11.3. Figure 11.3. Connecting window In the CONNECTING window click the button AUTODISCOVER. Figure 11.3. SALDA AIR will find MB-GATEWAY as shown in Figure 11.4. Figure 11.4 Autodiscover After this you can controll MB-Gateway via SALDA AIR, as shown in figure 11.5. Figure 11.5. SALDA AIR The company reserves the right to make changes of technical data without prior notice 15

12. Control MB-GATEWAY via SALDA AIR IOS application. Install SALDA AIR to mobile phone First go to App store in search input write SALDA AIR. Figure 12.1 App store 16 The company reserves the right to make changes of technical data without prior notice

In search list find SALDA AIR application. Click GET 12.2 Figure 12.2 SALDA AIR application Click INSTALL button in figure 12.3. Figure 12.3 Install SALDA AIR application window. The company reserves the right to make changes of technical data without prior notice 17

13. Start AIR SALDA on IOS Configurate wireless Go to wifi settings. Click scan button and then select SSID of the Router, which you write in Wireless Name of Range Extender field in figure 5.1. Figure 13.1 Security key window 18 The company reserves the right to make changes of technical data without prior notice

Enter the Security key, wich you write in Root AP Wireless Password field in figure 5.1. Click Connect figure 13.2. Figure 13.2 Security key window Start SALDA AIR on ios and CONNECTING window will appear, as shown in Figure 13.3. Figure 13.3 Connecting window The company reserves the right to make changes of technical data without prior notice 19

In the CONNECTING window click the button AUTODISCOVER. Figure 13.3. SALDA AIR will find MB-GATEWAY as shown in Figure 13.4. Figure 13.4 Autodiscover After this you can controll MB-Gateway via SALDA AIR in figure 13.5. Figure 13.5 SALDA AIR 20 The company reserves the right to make changes of technical data without prior notice

MB-GATEWAY III. TP-LINK WIRELESS N NANO ROUTER ACCESS POINT MODE CONFIGURATION VIA WIRELESS 1. Connect the router following the steps according to steps A to C in the diagram. Connect the LAN/WAN port of TL-WR802N to the wired network port with an Ethernet cable to MB-GATEWAY and connect TL-WR802N to the power. TP-LINK router A TL-WR802N s Wi-Fi name: TP-LINK_XXXX MB-Gateway B C Figure 1-1 Hardware Installation of the TL-WR802N in AP Mode 2. Wait for about 30 seconds until the router boots up, then connect to the router using the default Wi-Fi Name and Password printed on the Wi-Fi Info card. Figure 2.1. Figure 2-1 Wi-Fi Info card The company reserves the right to make changes of technical data without prior notice 21

LAPTOPS Click the icon at the bottom of your desktop. Click refresh button, and then select the default SSID of the Router. Click Connect Figure 2.2. Figure 2.2 Wi-Fi connection Enter the Security key from Wi-Fi Info card. Figure 2.1. Click Next. Figure 2.3 Figure 2.3 Security key window 22 The company reserves the right to make changes of technical data without prior notice

MOBILE PHONES, TABLETS Go to Wi-Fi settings. Click the button Scan and then select the default SSID of the Router Figure 2.4. Figure 2.4 Wi-Fi connection Enter the Security key from Wi-Fi Info card. Figure 2.1. Click Connect. Figure 2.5. Figure 2.5 Security key window The company reserves the right to make changes of technical data without prior notice 23

III.I. QUICK INSTALLATION GUIDE With a Web-based utility, it is easy to configure and manage the TL-WR802N 300Mbps Wireless N Nano Router. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 1. To access the configuration utility, open a web-browser and enter the default address http://tplinkwifi.net in the address field of the browser. admin admin Figure 1.1 Login window After a moment, a login window will appear, similar to the one in Figure 1.1. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key. 2. After a successful login, you can click the Quick Setup menu to quickly configure your Router. Figure 2-1 Quick Setup 24 The company reserves the right to make changes of technical data without prior notice

3. Click Next, and then Working Mode page will appear as shown in Figure 3.1, choose Access Point Mode and click Next on Working Mode in Figure 3.1. Figure 3.1 Working Mode page 4. Wireless Setting page will appear as shown in Figure 4.1. Enter Wireless Network Name and AP Wireless Password, then click Next. Figure 4.1 Working Mode page Wireless Network Name (SSID) - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXX (XXXX indicates the last unique four numbers of each Router s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test. Channel - This field determines which operating frequency will be used. The default channel is set to Auto. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. AP Wireless Password - Input the password of your broadcast SSID. The company reserves the right to make changes of technical data without prior notice 25

5. You can configure the IP parameters of LAN on this page. If you are not familiar with the settings on this page, it s strongly recommended to keep the provided default values, otherwise wireless network performance may be poor. After this click the button Next, Figure 5.1. Figure 5.1 Quick Setup Network Settings Type - Choose SmartDHCP to get IP address from remoter DHCP server, or choose static IP to configure IP address manually. IP Address - Enter the IP address of your system in dotted-decimal notation (factory default: 192.168.0.254). Subnet Mask - An address code that determines the size of the network. Normally 255.255.255.0 is used as the subnet mask. 26 The company reserves the right to make changes of technical data without prior notice

MB-GATEWAY 6. Click the Next button in Figure 5.1. You will then see the Finish page. Figure 6.1 Quick Setup - Finish 7. Click button Reboot (Figure 6.1) to reboot the router. After reboot connect LAN/ WAN port of TL-WR802N (A in Figure 7.1) to the wired network port with an Ethernet cable to MB-GATEWAY (B in Figure 7.1) and connect MB-GATEWAY to the ventilation system (C in Figure 7.1). A TL-WR802N s Wi-Fi name: TP-LINK_XXXX C MB-Gateway B TP-LINK router Figure 7.1 Hardware Installation of the TL-WR802N and MB-GATEWAY in AP Mode The company reserves the right to make changes of technical data without prior notice 27

8. Select new access point. LAPTOPS Click the icon at the bottom of your desktop. Click refresh button, and then select SSID of the Router figure 8.1, which you write in Wireless Network name (SSID) field in figure 4.1 or select root router. Click Connect. Figure 9.1 Wi-Fi connection Enter the Security key in the field Root AP Wireless Password. Figure 5.1. Click Next. Figure 9.2 Security key window 28 The company reserves the right to make changes of technical data without prior notice

MOBILE PHONES, TABLETS Go to Wi-Fi settings. Click button Scan and then select SSID of the Router, which you enter in the field Wireless Network name (SSID). Figure 4.1. Figure 9.3 Wi-Fi connection Enter the Security key in the field AP Wireless Password. Figure 4.1. Click Connect. Figure 9.4. Figure 9.4 Security key window 9. To access MB-GATEWAY, open a web-browser (Google Chrome is recommended) in address field type the MB-GATEWAY device name (hostname). According to the factory settings (default) MB-GATEWAY device name MBGW - plus the last six MAC address characters, for example., mbgw900154. In the page enter the login data: according to the preset parameters (default) username: admin password: admin. The company reserves the right to make changes of technical data without prior notice 29

10. Control MB-GATEWAY via SALDA AIR android application. Install SALDA AIR to mobile phone First go to Google play store in search input write SALDA AIR. Figure 10-1 Google play store application In search results list find SALDA AIR application. Click the application. Figure 10.2 Figure 10.2 SALDA AIR application 30 The company reserves the right to make changes of technical data without prior notice

Click the button INSTALL. Figure 10.3. Figure 10.3 Install SALDA AIR application window. In the window that appears click ACCEPT and application SALDA AIR will be installed. Figure 10.4 Figure 10.4 Install SALDA AIR application window The company reserves the right to make changes of technical data without prior notice 31

11. Start AIR SALDA. Go to Wi-Fi settings. Click button scan and then select SSID of the Router. Figure 11.1. Enter it in the field Wireless Network name (SSID). Figure 4.1. Figure 11.1 Security key window Enter the Security key in the field AP Wireless Password. Figure 4.1. Click Connect. Figure 11.2. Figure 11.2 Security key window 32 The company reserves the right to make changes of technical data without prior notice

Start SALDA AIR application for Android devices and CONNECTING window will appear. Figure 11.3. Figure 11.3 Connecting window In the window CONNECTING click the button AUTODISCOVER. Figure 10.7. SALDA AIR will find MB-GATEWAY as in shown Figure 11.4. Figure 11.4 Autodiscover After this you can controll MB-Gateway via SALDA AIR. Figure 11.5. Figure 11.5 SALDA AIR The company reserves the right to make changes of technical data without prior notice 33

12. Control MB-GATEWAY via SALDA AIR IOS application. Install SALDA AIR to mobile phone First go to App store in search input write SALDA AIR. Figure 12.1 App store 34 The company reserves the right to make changes of technical data without prior notice

In search list find SALDA AIR application. Click GET 12.2 Figure 12.2 SALDA AIR application Click INSTALL button in figure 12.3. Figure 12.3 Install SALDA AIR application window. The company reserves the right to make changes of technical data without prior notice 35

13. Start AIR SALDA on IOS Go to wifi settings. Click scan button and then select SSID of the Router figure 13.1, which you write in Wireless Network name (SSID) field in figure 4.1. Figure 13.1 Security key window 36 The company reserves the right to make changes of technical data without prior notice

Enter the Security key, wich you write in Root AP Wireless Password field in figure 4.1. Click Connect figure 13.2. Figure 13.2 Security key window Start SALDA AIR on ios and CONNECTING window will appear, as shown in Figure 13.3. Figure 13.3 Connecting window The company reserves the right to make changes of technical data without prior notice 37

In the CONNECTING window click the button AUTODISCOVER. Figure 10.7. SALDA AIR will find MB-GATEWAY as shown in Figure 13.4. Figure 13.4 Autodiscover After this you can controll MB-Gateway via SALDA AIR in figure 13.5. Figure 13.5 SALDA AIR 38 The company reserves the right to make changes of technical data without prior notice

Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by the manufacturer at any time and without notice. Such changes will, however, be incorporated into new editions of this manual. All illustrations are for illustrative purposes only and may not accurately depict the actual device. Full 300Mbps Wireless N Nano Router TL-WR802N specification you may find at http://www.tp-link.com. MB-Gateway quick launch guide is located at www.salda.lt or directly http://www. salda.lt/en/products/item/mb-gateway. Mobile application for Android is located at https://play.google.com/. Direct link: https://play.google.com/store/apps/details?id=lt.salda.air&hl=en. Mobile application for ios is located at https://www.apple.com/itunes/. Direct link: https://itunes.apple.com/us/developer/salda-uab/id1226456172

SALDA UAB Ragainės g. 100 LT-78109 Šiauliai, Lithuania +370 41 54 04 15 +370 41 54 04 17 office@salda.lt www.salda.lt