EZTAG Manual.qxp_Layout 0/0/06 :7 Page EZTAG PROXIMITY AND KEYPAD DOOR ENTRY USER MANUAL www.espuk.com
EZTAG Manual.qxp_Layout 0/0/06 :7 Page System Components Proximity and Reader 0 x Proximity Tags x Hex Key x Plastic wall plug x Countersunk screws x Diode and x Capacitor Optional Accessories EVBPSBB Lock Power Supply EV-EXIT Push to Release EV-EBG Emergency Release EV-ML-50/500XT Electro-magnetic Lock ENTERD Electric Lock
EZTAG Manual.qxp_Layout 0/0/06 :7 Page Contents Installation........................................................ EZTAG Wiring Example.......................................... 5 EZTAG Wiring Example.......................................... 5 Advanced Guide How to set-up Access Pin............................ 6 How to set-up Access Tags................................... 6 Deleting Access Pin or Tag.................................... 7 Changing Pin................................... 7 Clear all Pin and Tag Data..................................... 8 Default to Factory Settings.................................... 8 Lock Output Operating Time................................ 9 Enable Door Bell Facility...................................... 9 Enable Tamper Alarm facility................................ 0 Access Pin for Lock Output........................ 0 Deleting Access Pin for Lock................................ Lock Output Operating Time for Lock Output................ System setup record.............................................. User Guide....................................................... Technical Specification............................................
EZTAG Manual.qxp_Layout 0/0/06 :7 Page Installation Release hex screw from the bottom of the keypad (Side View) Push the keypad up to release from mount plate Thread system cable through the cable entry hole then make the system connections (as per the wiring diagram), mount the bracket to the surface and slide the keypad to the mountplate, re-fit the hex screw to secure into position. Note: if using more than one keypad, ensure that the keypads are mounted a minimum 85cm apart
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 5 EZTAG Wiring Example LEDs Capacitor for Electro-magnetic lock Diode for Electronic Lock Electro-magnetic lock _ + Electronic lock Lock -release time Red Black Green Purple Grey Pink NC + _ + _ N.C for Electro-magnetic lock N.O for Electronic lock Tag Reader EZTAG Wiring Example LEDs Red Black Green Purple Blue Grey Orange Pink Green/White N.O Purple/White COM Blue/White N.C Yellow White Tag Reader Input DC: +V - +V or Input AC: V - V N.O COM P.b for Lock (N.O) Output for Lock (Volt-free) N.C + _ Output for Lock (Volt-free) Push button for Lock (N.O) Speaker connection for door bell facility (8 0.5w recommended) 5
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 6 How to set-up Access Pin 9 0 a starting location number 0 0 0 9 9 9 Double 5???? a digit pin ( not be used) 6 How to set-up Access Tags 9 0 5 a unused location number* 0 0 0 9 9 9 5??? number of tags to be registered 6 Present the tag with the lowest serial number 7 All other batch tags will auto register end programming *Each tag will use up a location number 6
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 7 Deleting Access Pin or Tag the location 0 0 0 9 number of tag/pin 9 9 delete Changing Pin???? new digit programming pin???? Re-enter new digit programming pin 5 Note; access keypad s programming mode, the digit programming code is entered in twice 7
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 8 Clear all Pin and Tag Data 8 8 8 Default to Factory Settings 8 9 9 8
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 9 Lock Output Operating Time number of seconds 00-99?? Enable Door Bell Facility 0 enable 0 disable Becomes the door bell push in normal mode 9
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 0 Enable Tamper Alarm facility 6 0 enable 0 disable Tamper alarm activates the keypad s internal buzzer and door bell output if the light sensor is exposed Access Pin for Lock Outputt 9 0 an unused location number 0 0 0 9 Double 5???? a digit pin ( should not be used) 6 0
EZTAG Manual.qxp_Layout 0/0/06 :7 Page Deleting Access Pin for Lock the location number of pin delete 0 0 0 9 5 Lock Output Operating Time for Lock Output 5 number of seconds 00-99??
EZTAG Manual.qxp_Layout 0/0/06 :7 Page assist in future programming, it is recommended that a record is made of the system setup. System Location (000-999) Tag Serial Tag Owner Notes
EZTAG Manual.qxp_Layout 0/0/06 :7 Page System Location (000-999) Tag Serial Tag Owner Notes
EZTAG Manual.qxp_Layout 0/0/06 :7 Page User Guide release Lock access programming mode (A) a programmed Access Pin number (B) Present a registered tag Technical Specification DC input - volts AC input - volts Standby current 80ma Operating current (without lock) 0ma Working temperature -0c to +50c Reader frequency 5KHz IP rating 65 Dimension 50 x x mm
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 5 5
EZTAG Manual.qxp_Layout 0/0/06 :7 Page 6 Elite Security Products Unit 7, Target Park, Shawbank Rd Lakeside, Redditch B98 8YN Telephone: 057 5 5 50 Fax: 057 5 5 email: info@espuk.com E&OE - Errors and omissions excepted. L5 www.espuk.com