under 5 minutes under 0 minutes Tools Skills - Easy Under 5 Minutes* The LW00 series product is expandable. To order additional cameras please visit our website at Step - Connections * Installation time may vary based on application and camera cabling Includes: NOTE: AVOID INSTALLING IN A LOCATION WHICH REQUIRES THE WIRELESS SIGNAL TO PASS THROUGH CEMENT, CONCRETE AND METAL STRUCTURES. THIS WILL REDUCE THE TRANSMISSION RANGE. x Wireless Receiver x Power Adaptor (for receiver) x RCA Video Cable x USB Cable x Software CD Camera Battery Adaptor Cable(s)* Wireless Camera(s)* Power Adaptor(s) (for camera*) * NOTE: The antenna cosmetics are different for the LW00 vs. LW00P. These instructions however apply to both series of products. A - Wireless Receiver Set-up Installation The Camera can be powered either by using the provided Power Adaptor, or using a 9V battery (not included) in combination with the Battery Adaptor Cable. Connecting Camera to Power Adaptor Connect one end of the AV Cable to the back of the receiver. Connect the other end to the Video IN (Yellow) and Audio IN (White) ports on the TV or Monitor for viewing and VCR or DVD Recorder for recording. Plug the Receiver power cable into the 9V POWER input. Plug the power adaptor into a wall outlet or surge protector. How to use the Control Buttons: LW00P LW00 * Requires viewing/recording device with RCA. Viewing/Recording device sold separately. *Additional receivers and/or cameras sold wseparately. See product manual for details. AUTO BUTTON When the receiver is set to AUTO Mode, it will continuously switch between the cameras that are set to ON. The dwell time is set to 4 seconds per camera (by default), however this can be adjusted to ~0 seconds. To adjust the dwell time, press and hold both the AUTO and MANUAL buttons at the same time this will produce beeps indicating one second increments (i.e. each beep represents one second in dwell time). Once the desired dwell time has been reached, release the buttons. MANUAL BUTTON Press the MANUAL button to switch between available cameras. The Receiver will switch to a different camera (if available and configured) each time the MANUAL button is pressed. Place the receiver in a place that will have clear reception to your camera(s). Try to avoid placing the receiver near other 900MHz devices (such as older cordless phones, etc.) Helpful Tips: Better reception can often be accomplished by changing the position of the Receiver unit or changing the position of the Camera. The Receiver is a wireless product, and is subject to a number of environmental conditions. Walking between the receiver and camera may cause temporary interference. The optimal distance of the camera (during low light / nighttime use) from the person or object is 4~6 feet (up to meters). The picture may become grainy beyond this distance due to lack of light an additional light source in the room, such as a night light or illuminator may improve the picture quality. During low light / night use, the closer the Receiver is to the Camera, the better the picture quality. The picture may become grainy at farther distances. The optimal distance for normal home use is 5~60 feet (~8 meters), however the MAXIMUM RANGE is up to 00 feet in optimal conditions. Audio feedback may appear when the receiver and cameras are too close (under 5 feet / meters). Plug & Play connectors, On screen set up Did you know? You can move your camera around the house or from one room to another with the use of the included battery adaptor cable. TV (not included) Hi Speed B - Wireless Camera Installation * Number of cameras may vary by model. Check your package for specific content information. * Connect power adapter to local AC power outlet * of each provided with the LW00 System/ of each provided with the LW0 System. REMOTE COLOR WIRELESS SURVEILLANCE SYSTEM LW00 Series - quick start guide Connect the Power Adaptor to the Female Barrel Power termination on the camera. C - Viewing your System Turn on TV or Observation Monitor, and switch the video channel that the receiver has been connected to. Tip: If your TV has a PIP feature, you can have the camera images displayed in the PIP window. Check your TV manual for info on PIP feature (if available). Connecting Camera to the Battery Adaptor Cable (optional) Connect the Camera Battery Adaptor cable to the Female Barrel Power termination on the camera. Connect a battery to the cable. NOTE: The new 9V battery should last for approximately 4 hours without the IR LEDs in use. NOTE: Before you install the camera(s), carefully plan where and how it will be positioned, and where you will route the cable that connects the camera to the power adaptor or battery adaptor. Before starting permanent installation, verify its performance by observing the image on a monitor. When camera is positioned in same location/position where it will be permanently installed. NOTE: Wireless cameras require a power source (either an electrical outlet or battery power) to operate. If you plan to permanently mount the camera in a location, it is recommended to use the included Camera Power adaptor to prevent interruptions in the image, as the battery adaptor is intended as a temporary power solution. LW00P ONLY - Optimizing Wireless Signal In order to provide the best wireless transmission, you will need to adjust the antenna of the camera and receiver as follows.. Position the receiver s patch antenna to face the direction of the camera. Position the camera s patch antenna to face the direction of the receiver. Adjust the direction as necessary while observing the screen. Patch Antenna LW00 Series QSG_EN_R Page
REMOTE COLOR WIRELESS SURVEILLANCE SYSTEM Skills - LW00 Series - quick start guide Under 0 Minutes* Computer & Plug & Play connectors, On screen set up Step - Viewing on your PC Driver Installation - on Windows XP Insert the included CD into your PC s CD-ROM drive. A Lorex Software Installation Menu will appear on your screen as per image shown. Click USB Driver to install the driver called Usbvm6. Follow steps in installation wizard. Press Continue Anyways when prompted by the software installation screen. You will be prompted to install Microsoft DirectX. Please proceed with the install as this is required to run the software. Next you will be prompted to restart your PC. Please do so. NOTE: Notice upon restarting your computer that a file called AMCAP W has been added to your desktop. See Step-5 for further details. cable and connect one end 4 Take the included USB to the back of the wireless receiver and the other end to your PC. The New Wizard will appear on screen. Select No, not this time to find the driver manually. Click Next. Select Install from a list or specific location (Advanced). Click Next. Select Search Removable Media and click Next. At this point make sure the CD is still inside the CD-ROM drive. The driver will automatically be found. A Confirm File Replace box will appear. Click No. NOTE: You may be prompted by the Windows alert. Press Continue Anyways and press Finish to continue. 5 Check to see if the receiver and camera have been properly installed by double clicking the AMCAP W icon found on your desktop. NOTE: Make sure the camera is powered up and within range of the receiver or else you will not see a picture when you start AMCAP W Viewer software. Driver installation is now completed. Driver Installation - on Windows Vista Insert the included CD into your PC s CD-ROM drive. CD Click on Open folder to view files to access the CD content. Click on folder called Software and double click USB Driver. NOTE: A warning will pop-up stating Windows cant verify the publisher of this driver software. Click Install this driver software anyway. You will be prompted to install Microsoft DirectX. Please proceed with the install as this is required to run the software. Next you will be prompted to restart your PC. Please do so. NOTE: Notice upon restarting your computer that a file called AMCAP W has been added to your desktop. See Step-6 for further details. Take the included USB cable and connect one end to the back of the wireless receiver and the other end to your PC. The driver installation will be completed automatically. 4 Check to see if the receiver and camera have been properly installed by double clicking the AMCAP W icon found on your desktop. NOTE: Make sure the camera is powered up and within range of the receiver or else you will not see a picture when you start AMCAP W Viewer software. LW00 Series QSG_EN_R Page
under 5 minutes REMOTE COLOR WIRELESS SURVEILLANCE SYSTEM under 0 minutes Skills - Hi Speed LW00 Series - quick start guide Under 0 Minutes* Yoics Software Installation - on Windows XP Your Internet Browser will open up and direct Go back to the Lorex you to the download page within the Yoics Software Installation Plug & Play connectors, On screen set up Step - Viewing on your PC (continued) Menu by clicking on My Computer and double clicking on the Lorex icon. Computer & website (appears as a blank page). The Web Browser may warn you about the download. Click Download File to proceed. NOTE: Yoics software requires Microsoft.NET software. If this software is not already installed on your PC, you will be prompted to install this. Click on Software Installation and select Yoics Software Download Latest Version to download Yoics remote viewing application. When prompted by the software, press Run to proceed and complete the installation of the Yoics software. Continue to Step-4 on the next page Yoics Software Installation - on Windows Vista Make sure if the CD is still inside the CD-ROM drive. On your desktop click on Computer to access the CD-ROM drive and select Run Lorex.exe Click on Software Installation and select Yoics Software - Download Latest Version to download Yoics remote viewing application. Your Internet Browser will open up and direct you to the download page within the Yoics website (appears as a blank page). The Web Browser may warn you about the download. Click Download File to proceed to Step -4. Continue to Step-4 on the next page LW00 Series QSG_EN_R Page
COLOR WIRELESS SURVEILLANCE SYSTEM LW00 Series - quick start guide Step - Viewing on your PC (continued) 4 After a minute or two the Yoics login screen will appear. Click on Register a new Yoics account to setup a Yoics account. 5 Click on Click here to register new Yoics account check box. 6 Proceed to fill in all the required information. Click Register. When the Yoics setup wizard appears, check Do not ask me about this when Yoics starts checkbox. Press Skip Setup. 7 The Yoics desktop software will now open after a few minutes. Click on Web Cam to add the camera to the list of items you would like to view. 8 the installed devices list. It will show up as Wireless PC-Camera. Enter a name for the camera in the Alias field (e.g. Wireless). NOTE: Before you proceed, note the options that are checked by default. Uncheck any that you do not require. Press Change to select the camera from Press Change and select a folder to save the camera images to (i.e. desktop or my pictures ). Press Ok. Wireless 9 After a minute, the Yoics Share Registration is Complete message appears. Press OK. The camera will appear in the Yoics desktop application under the Alias setup as in step section 8 -. TIP Once the Yoics login screen reappears, press Login. Find below the status of the connected devices 0 Right click on the Alias of the camera and select Connect. The status of the device will change to orange to indicate that is now ready to be viewed locally or remotely. blue means that your device is on-line and available. green means a device from another user is online and available to you for sharing orange means that you are connected to the device grey means a device which is currently off-line and not available. An Internet browser window will pop-up and show a live image from the camera. Click on the image to see streaming video from the camera local viewing on a PC LW00 Series QSG_EN_R Page
under 5 minutes under 0 minutes COLOR WIRELESS SURVEILLANCE SYSTEM Hi Speed- Basic Skills LW00 Series - quick start guide 5 Minutes Step - Remote Viewing on a Web Browser / iphone / ipod touch Once logged in to your account, you will notice the camera appearing in My Stuff. Click on the link to view the camera. Basic Computer Skills Remote Viewing on a Web Browser (PC & Mac) Open up your web browser and visit http://lorex.yoics.com and enter your Email/ID and Password in the top right corner of the page to login to your online account. Computer & Click on the image to view live streaming video from the camera NOTE: Video streaming performance is directly related to factors such as local and network internet speed. remote viewing on any PC Remote Viewing from iphone or ipod touch Using Safari, go to http://lorex.yoics.com and login using username and password. Click the camera you want to view. OPTIONAL: In newer versions of iphone/ipod itouch, you can bookmark the Yoics website for quick access. Alternatively create a shortcut on the application screen for access. Check the reference materials that came with your iphone / ipod touch for further details. ipod touch and ipod are trademarks of Apple Computers, Inc. Registered in the USA and other countries. remote viewing on your iphone or ipod touch. It s all on the Web For detailed setup information, please refer to your User s Manual. For additional information, please visit our website /support LW00 Series QSG_EN_R Page