Camera control panel FRREZE image storage BLACK & WHITE changing colour / blackwhite DISPLAY status sign ZOOM TELE digital zoom high ZOOM WIDE digital zoom low POS PRESET set function memory POS RESET delete function memory POS 1 function memory 1 POS 2 function memory 2 AE auto change Manual / Automatic shutter BRIGHT UP Increasing exposure time BRIGHT DOWN Sinking exposure time WB automatically white balance Technical Parameter Sensor 752 x 582 Pixel ¼ CCD Norm PAL 25 frames / sec. Shutter 1/50x 1/10.000 sec. Resolution 460 TV lines Zoom 4-fach digital / 4 fold digital Video output (1) FBAS Video output (2) Y/C S-video RS 232 control VICSA PROTOCOL Remote control resistance matrix Power supply 6 12 Volt Power consumption 1,6 Watt Dimensions 106 mm x 36 mm x 105 mm Operating temp. 0 C to 45 C / 0 to 45 camera module Sony FCB-IX 11 AP User Guide KAPS Image Cam for Microscope.docpage 1 of 6
Front side 12 pin connector (coming from integrated beam splitter) Rear side Ein/Ausschalter / ON / OFF Stromversorgung / power 9-12 V / Video signal FBAS (BNC) Video signal YC (S-Video) Fuß/Handschalter / Remote control RS 232 connection Name: order no.: Video camera Image Cam 700-868 Power supply NT 12/15 700-869 YC cable 5m 700-873 BNC cable 8m 700-700 Mounting attachment swivel arm old 101-805-004 Mounting attachment swivel arm new 101-805-005 Internal power supply set 101-806-000 To get the best colour temperature and natural colours you have to make a white balance. Put a white sheet of paper under the microscope Turn the Illumination to Maximum Push 3 sec. the round WB push button for the new adjustment White balance is from now storage User Guide KAPS Image Cam for Microscope.docpage 2 of 6
Image Cam system installation with internal microscope power Optional, internal power supply set (101-806-000) if ordered: In the swivel arm integrated more pin power plug (power output 12 Volt) Connector with power cord (2,5 mm plug) Mounting bracket with attached Image Cam (2 distance holders) 1. Add the mounting bracket with Image Cam to the swivel arm and tighten with the enclosed screw (image 5) 2. The bracket is fitted at the opposite side with 4 screws (image 1) 3. Connecting of the more pin connector with the integrated plug of the swivel arm (image 2,3) 4. Connect the power cord with the Image Cam (image 3,4) After switching on the microscope, the video camera is ready too! User Guide KAPS Image Cam for Microscope.docpage 3 of 6
Safety Precautions Note To ensure the safe operation of this unit, be sure to heed the following precautions. Do not allow foreign matter to enter the unit Allowing water or other foreign matter to enter the cabinet may lead to fire and/or injury. If water or other foreign objects happen to enter the cabinet, switch off the power supplied to the unit, disconnect the DC power cord or connections cables and contact your authorized Sony dealer. Do not dismantle or modify the unit Disassembly or modifications of the unit may lead to fire and/or injury. Leave all adjustments, inspections and repairs of internal components to your authorized Sony dealer. Be sure to install the unit properly For queries on installation, contact the store where you purchased the product, or contact your authorized Sony dealer. When attaching the unit to a wall or ceiling, make sure the point of attachment has sufficient strength to support the weight of the unit and mounting bracket. If the point of attachment lacks sufficient strength, the unit may fall, resulting in severe injury. Check the mounting brackets once a year to see that it remains tight. Use recommended power supplies Be sure to use the power supply (camera adapter or AC power adapter) specified in this manual. An unspecified power supply used with unit may become a fire hazard. Use recommended DC cables and connection cables Use of DC cables and connection cables other than those specified in this manual may lead to fire. Take care do not damage cables Use of damage DC cables can lead to fire. Take special note of the following. Take care not to wedge cables between equipment and racks, walls, etc., during installation. Do not modify the DC cables and take care not to damage them Do not place heavy objects on the cables or pull them with excessive force. Do not place cables near heating devices or other heat sources. When disconnecting a cable, always pull from the plug; not the cable itself. If the DC cables become damaged, discontinue use and contact your authorized Sony dealer for replacement. Continued use of damaged cables may lead to fire. User Guide KAPS Image Cam for Microscope.docpage 4 of 6
Do not install or operate in environments subject to high levels of smoke, steam, humidity or oil Operation in any of the above environment may lead to fire. Use of this product in environments other than those specified in this manual may lead to fire. Do not place unit on an unstable base The unit may fall physical injury if used in any of the following places: On top of shaky, unstable table. On inclined surfaces In places subject to vibration or shock Check that the place of attachment is strong enough to support the weight of this unit, and that the unit and attachments device are secure. Disconnect the DC cable and connection cables before moving the unit If the unit is moved with the DC power cable and Connection cables still attached, the cables may be damaged resulting in fire. Operating Precautions Operating or storage location Avoid operating or storing the camera in the following locations: Extremely hot or cold places ( Operation temperature:-5 C to +45 C [23 F to 113 F] ) In direct sunlight for long periods, or close to heating equipment ( e.g., near heaters) Ventilation To prevent internal heat build up, do not block air circulation around the camera. Transportation When transporting the camera, repack it as originally packed at the factory or in materials equal in quality. Cleaning Use a soft, dry cloth to clean the external surfaces of the camera. If it is very dirty, use a soft cloth damped with a small quantity of neutral detergent, then wipe dry. Do not use volatile solvents such as alcohol, benzene or thinner as they may damage the surface finishes. User Guide KAPS Image Cam for Microscope.docpage 5 of 6
Cable Connections Remote control Pin 1 - AD6 Zoom Pin 2 - AD7 ICR Pin 3 - AD3 colour adjustment Pin 4 - AD4 exposure Pin 5 - AD5 Focus Pin 6 - AD0 Parameter storage Pin 7 - AD1 Display function Pin 8 - AD2 Image adjustment Schirm - GND SVHS Y/C video signal Cable Y/C 4pol.MiniDIN to 4pol. MiniDIN necessary Pin 1 - GND Pin 2 - GND Pin 3 - Y OUT Signal Pin 4 - C OUT Signal FBAS video signal BNC cable required Pin outside - GND Pin centre - Signal Power supply Power supply or cable necessary from microscope Pin outside - GND Pin centre - 9 12V DC User Guide KAPS Image Cam for Microscope.docpage 6 of 6