Dimmable Constant Current Rev 8-9-7 Electrical Specifications Input Voltage Range: Frequency: Power Factor: Inrush Current: Input Current (Max): -77 Vac Nom. (8-35 V Min/Max) 5/6 Hz Nom. (47-63 Hz Min/Max) >.9 @ full load, V through 77V <3. Amps max @ 77 Vac.56 Amps @ V, 6Hz.5 Amps @ 77V, 6Hz Maximum Power: 55W Line Regulation: ±% Load Regulation: ±3% THD: < % @ > 6% full load Ripple Current: 5% (Max) Start-up Time: 5mS (typical) Protections Over-voltage Short Circuit Yes Auto Recovery Environmental Specifications Max Case Life Temp: (5 year warranty) 66 C Maximum Case Temp (UL): 8 C Type TL Rating: 86 C/ 6 C Minimum Starting Temp: -3ºC Storage Temperature: -4ºC to +85ºC Humidity: 5% to 9% RH Cooling: Convection Vibration Frequency: 5 to 55 Hz/g, 3 minutes Sound Rating: Class A Lifetime: 5, Hours @ 67ºC @ Tc point EMC: FCC 47CFR Part 5 Class A compliant Model E336 Output Current (ma +5%) Output Voltage (Vdc) Max Output Power (W) Type TL Rating Typical Efficiency LED55WPG-55-C5-D -5-55 55 86/6 C 88% Class : US/Canada TYPE TL Program driver with GUI software for fast setup Option to program output current with resistor Linear or logarithmic dimming curve options Flicker free output for comfort and critical applications -stage power supply design for better performance over wide range of outputs Auxiliary Vdc, ma output for powering controls or fans NTC option allows for themal protection of LED engine Adjustable Output Current: -5mA UL Dry & Damp Location Rated, Class, Type TL Dim to zero with -V dimming Metal housing Required Programming Tools Model PG-C3 PG-SW Safety Certification UL/CUL CE EMC Standard FCC, 47CFR Part 5 EN 555 EN 6-3- EN 6-3-3 EN 6-4-5 Energy Star Description TRP Programming Cord (3 ft. long); REQUIRED TRP Programming Software DOWNLOAD Standard UL875, UL3 for UL Class & CAN/CSA C. No. 5.3, UL Type TL 86/6 C EN6347-, EN6347--3 Notes Class A Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment. Part 3-: Limits for harmonic current emissions Class C, 8% Rated Power Part 3-3: Limitation of voltage changes, voltage fluctuations and flicker. Part 4-5: Surge Immunity test, kv L-N, 4 kv L-FG & N-FG Energy Star transient protection: Ballast or driver shall comply with ANSI/IEEE C6.4.- and ANSI/IEEE C6.4.-, Category A operation. The line transient shall consist of seven strikes of a khz ring wave,.5 kv level, for both common mode and differential mode. Pg of 7
Dimensions 3.8 [78.3]. [5.6]. [5].64 [67] (TOP OF CASE).56 [6.5] (Tc) Point.689 [7.5].3 [8.]. [5] R. [R.5] WHITE (N) BLACK (L) GREEN (GND) USB NTC RSET +V V+ V- R. [R3]. [5].64 [67] PUSH IN CONNECTORS Wire Gauge: AWG -8.6-. mm.35 [9.] Insulation Strip Length LED Light Engine Remote Mounting Recommended maximum wiring distance at full load. R.6 [R.5].8 [4.5] 3.8 [96.6] 4.4 [7.7] AWG # # # Distance (m) 4 Distance (ft) 3.8 39.4 45.9 #9 #8 8 59 7. 3.63[9.3] -RO. [R.5] 3.8[78.3]. [8].6 [5.9].47 [].69 [7.6] Power Characteristics. Power Factor / Load 3% THD / Load.95 5% PF.9.85 V/6Hz 3V/5Hz 77V/6Hz THD % V/6Hz 3V/5Hz 5% 77V/6Hz.8.75 % 5%.7 % % 6% 8% % % Load 6% 8% % Load Lifetime / Case Temperature Typical Efficiency / Load 4 % 95% 8 6 4 Efficiency 9% 85% 8% 75% 7% V/6Hz 3V/5Hz 65% 77V/6Hz 4 45 5 55 6 65 7 75 8 Case Hotspot Temperature ( C) Note: The area under the life-temperature curve represents where the driver has highly reliable operation within specification. performance may drift out of published specifications as the hours of operation exceed the curve at a given temperature. Higher operating temperatures increase the chances of a failure to function. Other electrical, mechanical and environmental factors affect driver lifetime but are not represented in this calculation. 6% % 6% 8% % Load UL Conditions of Acceptability See website for additional information Pg of 7
Wiring Connections (White) NEUTRAL (Black) LINE (Green) GND (NEUTRAL) (LINE) (GROUND) INING POWER USB Programming Cord (PG-C3) (Gray) NTC (Gray) RSET (Purple) (Gray) - (Gray) V@mA (Red) LED+ (Blue) LED- PURPLE + GRAY - OPTIONAL FOR NTC OPTION FOR RSET OPTION -V DIMMER or CONTROL RSET RESISTOR NTC LED ENGINE -Vdc Dimming Parameters Min Typical Max V Auxiliary Output V.V 3.V V Auxiliary Output Source Current ma - ma Absolute Voltage Range on -V Input () Source Current out of -V Input () -. V - +5 V ma -.5 ma. Single series strings of LEDs will perform best with deep dimming settings.. LEDs with parallel strings (discrete component or COB) may not perform well with deep dimming settings. 3. Specific LED and driver combinations must be tested to determine the lowest output setting for stable performance. Output Current % 9 8 7 6 5 4 3 Output Current / -VDC Dimming Control Voltage Min set to % Linear Logarithmic V V V 3V 4V 5V 6V 7V 8V 9V V Purple-to-Gray Voltage (Vdc) Output Current % 9 8 7 6 5 4 3 Output Current / -VDC Dimming Control Voltage Min set to % Linear Logarithmic V V V 3V 4V 5V 6V 7V 8V 9V V Purple-to-Gray Voltage (Vdc) Pg 3 of 7
Wiring Typical Dimming Circuit: -Wire Resistance Typical Dimming Circuit: -Wire -V Analog +V OUT (No Connection) Leviton IP7 Wall Dimmer (Example) +V OUT (No Connection) V -V Sink (Dimmer must be current-sink type control) Typical Dimming Circuit: 3-Wire Resistance Typical Dimming Circuit: V Powered Control +V OUT Potentiometer +V OUT +V IN + - -V OUT Dimmer/ Control/ Sensor. Part comes with, & +V auxiliary connectors. and +V return are connected to. This is for controls and sensors that need a V supply.. Part is compatible with most -V Wall Slide dimmers and direct -V analog signal. Recommended dimmer is Leviton IP7 or equivalent connected between Purple and wires. 3. Output current will be Minimum Programmed Value when Vdim.V. If set to % then this indicates dim to zero operation. 4. Output will be % with / open or above 9.V and Minimum Programmed Value with / Shorted. 5. Minimum dimming level is programmable with TRP Programming software. 6 OPERATING WINDOW Vout (Vdc) vs. Output Current 55 5 45 Vout (Vdc) 4 35 3 Minimum POC 5 5 3 4 5 6 7 8 9 3 4 5 Pg 4 of 7
Programming The Output Select resistance (RSET) from the table for required output current (ILED). Connect as shown in the wiring diagram. Table (full range) POC POC POC POC POC POC POC.9 87 4.7 348.5 649 39.4 58.8 6 79. 487.7.8 9 4.5 357 4. 665 335.4 4 58. 3 85.4 499 6.6 5 3. 96 44.7 365 7.6 68 34.3 7 537. 37 86. 5 4. 7 4. 46.5 374.3 698 347.5 3 545.9 43 89. 53 53.3 5.5 5 48.7 383 5. 75 353.7 33 554.8 49 84.5 536 67. 3 6.9 5.9 39 8.8 73 359.9 37 566.5 55 853.9 549 8.7 5 7.9 5 53. 4 3.9 75 366.4 4 575. 6 866. 56 93.9 8 9. 55.8 4 37. 768 37.8 43 583.7 67 878. 576 37.8.6 6 58. 4 4. 787 379.6 47 595. 74 89.7 59 3. 4. 3 6.7 43 45. 86 386.3 5 63.4 8 93.3 64 334.4 7 3.4 37 6.9 44 49. 85 393. 54 64.5 87 96.5 69 348. 3 4.8 43 65.5 453 53.6 845 399.9 58 65.4 94 99.5 634 36.3 33 6. 49 68. 464 58. 866 47. 6 636. 3 94.3 649 374. 37 8. 55 7.7 475 6.4 887 44.4 65 644. 39 956.6 665 387.6 4 9.4 6 73.3 487 67. 99 4.9 69 654.8 36 968.9 68 4.7 43.7 67 75.9 499 7.9 93 49.3 74 667.8 34 98.6 698 44. 47.6 74 79. 5 76.6 953 436.7 78 678. 33 996. 75 47. 5 3.9 8 8.6 53 8.3 976 444.3 8 688. 34 9.4 73 439.8 54 5.8 87 84.6 536 86.4 45. 87 7.7 348.3 75 45.8 58 7.6 94 87.6 549 9.4 458.8 9 7.6 357 36.6 768 465.5 6 9.4 3 9.6 56 96.5 5 468.5 96 7.8 365 49. 787 478.4 65 3.8 39 94. 576 3.8 7 475. 73.4 374 6.8 86 49.9 69 3.6 36 97. 59 37. 484.5 5 744.3 383 76. 8 5. 74 34.8 34.4 64 3.5 3 494. 755.9 39 89.3 GUI SET 78 36.6 33 3.8 69 38. 5 5.3 5 767.5 464 85. 8 38.4 34 7. 634 33.8 8 59.6 78. 475 98.5 Reading Resistor Codes K % resistor Black Brown Red Orange Yellow Green Blue Purple Gray White figures figures figures multipliers tolerance 3 4 5 6 7 8 9 3 4 5 6 7 8 9 3 4 5 6 7 8 9.. K K K M M % Silver 5% Gold % %.5%.5%.%.5% 6 4 8 6 4 5 33 39 47 Output Current vs. 56 68 8 5 8 7 POC Setting: If is open, TRP Programmer GUI can be used to set. Output Current vs. or GUI value is within ±5%. can be any /4W, ±%, V rated resistor. ¹ >9,9 Ohms will default to GUI setting. 33 39 47 56 68 8 98 94 98 Table (nominal output currents) (Ω) 6 3 3 6 7 8 3 395 3 44 5 569 3 698 35 845 4 996 45 5 5 49 6 87 7 3 8 8 9 33 366 5 53 5 57 3 6 35 68 4 746 45 8 5 98 5 GUI SET. Minimum wattage resistor rating is /4W leaded.. Larger wattages can be used for easy installation. 3. RSET best placed in LED engine to avoid field replacement programmability issues. 4. If RSET is placed on LED engine, SMD 85 size is recommended. Pg 5 of 7
Module Temperature Protection using External NTC (Negative Temperature Coefficient) Select a Negative Thermal Coefficient (NTC) resistor with a resistance range that allows the full output current to flow at safe LED operating temperatures. NTC resistance should drop sufficiently to allow reduced output current at elevated or harmful LED temperature levels. NTC operation should be thoroughly tested to ensure proper operation over all the full temperature range of the and the LED Engine. Example: NTC High, NTC Low and NTC Minimum % can be programmed using TRP Programmer USB interface & TRP PC based GUI Software. Factory Default Settings: NTC Low =.K ~ %, NTC High = 6.3K, % settings: NTC Minimum Level (%), NTC Minimum Ohms, NTC Maximum Ohms. % Output Current (%) vs. NTC % 8% (%) 6% 4% % % 8 4 6 8 3 3 34 36 38 4 4 44 46 NTC 48 5 5 54 56 58 6 6 64 66 68 Module Temperature Protection Example NTC = 85SMD, R 5C = 5K Ohm ± %, R 64C = 37, Vishay Part #: NTCS85E353GMT With part set: NTC Max = 6.3K, NTC MIN =.K, Min = % % Output Current (%) vs. NTCS85E353GMT NTC Temp ( O C) % 8% (%) 6% 4% % % 5 3 35 4 45 5 55 6 65 7 75 8 85 9 95 NTC Temp ( O C) Pg 6 of 7
Programming TRP s NTC Output Current (POC): from ma to 5mA NTC settings: NTC Minimum Level (%), NTC Minimum Ohms, NTC Maximum Ohms. Factory Default: NTC Minimum =.K, ~ %, NTC Maximum = 6.3K, % dimming curve: Linear or LOG Factory Default: Linear Dimming Curve Minimum Dim Level: % (OFF) to % programmed value. Factory Default: Min dim level % TRP Programming Tools: The TRP programming tools consists of programming software along with a special programming cord connected between the USB port of a computer and the TRP programmable LED driver being configured. The TRP programming software is a Windows PC based graphical user interface (GUI) that allows the user to program and configure the operating parameters of a TRP programmable LED driver. This interface allows the operator to set the LED drivers output current within its specified range. It also provides the ability to enable/disable and control features like "Dimming", "Auxiliary Output", "NTC Thermal Protection", "Constant Lumen Module", & "End-of-life indicator" when available in the LED driver being programmed. Programming Cord (PG-C3): This is a specially designed cord adapter with USB connectors for linking the computer and the LED driver being programmed. This unit also provides all power required to the LED driver being programmed. A standard USB cable can be used to extend the length of the Programming Cord from the computer USB port. The micro-usb connector on the Programming Cord must be connected directly to the TRP Drive. Programming Software (PG-SW): The programmer software is the windows based GUI that allows the user to assign custom part number(s) to the LED driver being programmed. The user can then save the driver profile to an external file and recall as needed. The "Auto Program" feature allows many LED drivers to be programmed to the same stored profile. This can be done by plugging the cord to each driver and a single click of the mouse. The programmer software supports bar code scanners. The barcode scanner can be used to automate the programming of the attached LED driver. This barcode scanner interface also provides an option to either enable or disable logging of the parameters to an Excel file. Download the PG-SW software from the TRP website: http://trpssl.com/driver_downloads.html The programming of the LED driver does not require the input be connected to an AC power connection. The TRP Programming Tool and the required LED driver circuitry will be powered from the programmer module via the USB connection to a computer. For new GUI settings to take effect the AC input must be cycled off/on and the USB interface disconnected. Labeling s: It is highly recommended that the drivers be labeled with information traceable to the programming profile. It can include the programmed output current, dimming curve type, minimum dimming level and name of the file storing the profile. This information is critical to answering any field questions from the contractor or end user. Parameters Parameter Minimum Value Maximum Value Factory Default GUI RSET Output Constant Current () ma 5 ma ma YES YES Disable Dimming? NO YES NO YES N/A Dimming Curve LINEAR % N/A Fixed % % YES N/A LOG % N/A Fixed % % YES N/A NTC Minimum Ohms K Ω K Ω K Ω YES N/A NTC Minimum % ~% % ~% YES N/A NTC Maximum Ohms K Ω K Ω 6.3K Ω YES N/A Pg 7 of 7