bars required for addequate signal Signal Strength Meter Point client bridge at access point in control room to obtain required signal strength. Sign onnections lack Line White Neutral Green Ground Wirenuts Provided lient ridge (see sheet 6 for mounting) ross Over Ethernet Signal to /Signal-In ccess Panel. Raintight ox (See Sheet ) lient ridge Mount in lear-line-of-sight to wireless transmitter. Ethernet able (straight through from receiver to POE) to Raintight ox Grounded pigtail located inside x box. Must connect when connecting power. Make connections by removing other access panel near / Signal-In panel. Replace all covers when connections have been made. Feed panel through hole as shown to change location of access panels. * isconnect Switch from ranch ircuit Sign to x ox (consult installation instructions for amperage requirement) /Signal-In panel can be relocated to side, bottom or back of message centers for wall mount or adjacent signs. Note: It is not necessary to remove message center display panels to make any connections. * National Electric code requires a disconnect switch within Sight of the sign or lockable within the building. If neither is available, install a disconnect at the sign. Important. Read before installation. entrances are located on access panels with x box. The location of this panel may very between different message centers. ccess panels can be swapped to allow placement of incoming power/signal on the side, back or bottom of the message center typically. This sign is intended to be installed in accordance with the requirements of rticle 600 of the National Electrical ode and/or other applicable local codes. This includes proper grounding and bonding of the sign. ll personnel who work with electrical connections must be educated in the safe procedures for installing and repairing electrical connections before they are given the responsibility of performing such tasks. onduit and fittings are supplied by installer. Note: For indoor installations, a raintight box is not required. Make connections same as above. rawn Message enter ate rawing No. JW 7/9/0 6 Greenville, Illinois 66 75-07
5' Ethernet (color coded white) straight through from "POE" to wireless receiver (supplied by Nevco) adapter supplied by Nevco. Signal to message center Water-tight bushing supplied by Nevco (for ethernet cable to wireless receiver) Water-tight fittings required (supplied by others) Incoming ox, outlet and cover supplied by Nevco. 5' ethernet crossover from "LN" to message center SIGNL-IN. olor coded red. Over Ethernet Supply (POE) Mounting POE:. ut supplied adhesive-backed fastening material into () " pieces.. Peal backing off of one piece and place on back of raintight box in desired location.. Place second piece on back of POE.. Press POE firmly onto back of raintight box. POE Inside Raintight ox (oor Removed for larity) Ethernet: Wireless Receiver Ethernet; Message enter Signal Notes.. Use raintight fittings.. Indoor installations do not require a rain-tight box. Make connections same as above. rawn Message enter JW ate 7/9/0 rawing No. Greenville, Illinois 66 6 75-07
Temperature Sensor Photo ell ) Place in a discrete location. ) o not completely enclose the sensor box. ) Placing the sensors in direct sunlight can elevate the temperature readings. Note: It is not necessary to remove display panels to make any connections. onnect cable from sensor to Temp. Sensor Photo ell cable located behind /Signal-In access panel. Install through supplied bushing. * onnections can be made using / conduit. to x box. * /Signal-In ccess Panel Signal-In - cross over ethernet from POE - remove knockout label 'Signal In' on panel to make connection Remove other access panel to make connections and replace when finished. Wires for connections located inside cabinet. Message enter Remove knockout on panel here to make connection. 7/9/0 rawing No. rawn ate JW 6 Greenville, Illinois 66 75-07
For double sided message centers, connect cable here and run straight through to Signal-In of second message center. Single abinet Message enter Temperature Sensor/ Photo ell (remove plug or knockout to make connection) Multi-Section Message enter /Signal-In Panel Note: Remove knockouts in access panels where necessary to make connections. Signal-Out Remove panel and re-mount according to label with x box on outside of cabinet. /Signal-In Panel Multi-Section, ouble Sided Message enter Slave Right Signal In Message enter Master Left onnect ethernet from Signal-Out of first cabinet straight through to Signal-In of second cabinet. abinet is identified by Nevco logo next to / Signal-In panel., Signal-In (ethernet connection from media converter) Important. Read before installation. entrances are located on access panels with x box. The location of this panel may very between different message centers. ccess panels can be swapped to allow placement of incoming power/signal on the side, back or bottom of the message center typically. This sign is intended to be installed in accordance with the requirements of rticle 600 of the National Electrical ode and/or other applicable local codes. This includes proper grounding and bonding of the sign. ll personnel who work with electrical connections must be educated in the safe procedures for installing and repairing electrical connections before they are given the responsibility of performing such tasks. onduit and fittings are supplied by installer., Signal In Slave Left Slave Right Signal In Message enter Note: abinet to cabinet signal connections are straight through ethernet. rawn Message enter JW ate 7/9/0 rawing No. Greenville, Illinois 66 6 75-07
ccess Point Network cable to P Ethernet Interface (crossover) lient ridge See Important Note elow ccess Point 5' ethernet straight through. (color coded white) Remove cover and plug into ethernet port closest to the center of the access point. ' rossover able (color coded red) LN Over Ethernet (POE) Supply Important Wireless devices should be in lear Line of Sight from each other. Penetration of obstacles by the wireless signal is dependant on the material of the obstacle as well as the overall distance between devices. oth units are suitable for outdoor installation. If building walls become a problem, mount the access point outside the building. rawn Message enter ate rawing No. JW 7/9/0 5 6 Greenville, Illinois 66 75-07
Fasten client bridge to mounting bracket using supplied zip-ties. olt or clamp bracket to column or other structure. (hardware supplied by others) Run zip-ties through two holes in bracket and through slot on client bridge. lient bridge can be mounted to bracket at various angles to achieve optimum line of sight to access point in control room. Message enter rawing No. rawn ate JW 7/9/0 6 6 Greenville, Illinois 66 75-07