CyberParallel PCIe Quick Installation Guide Introducing the CyberParallel PCIe The CyberParallel PCIe high-speed parallel adapter provides one additional parallel port to your PCI Express enabled system. Features and Benefits Compliant with PCI Express Base Specification Revision 1.0a PCI Express 1-lane (x1) parallel adapter works with PCI Express slots with different lane width Full support for Windows-based software Supports EPP/ECP and SPP (standard) parallel port modes System Requirements PCI Express enabled system with an available PCI Express slot Windows 7 (32-/64-bit) / Vista (32-/64-bit) / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000 Package Contents CyberParallel PCIe adapter Spare enhanced low-profile bracket Driver CD Quick installation guide 04-0422C 1
Layout Parallel Port Figure 1. Layout Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. Note: For low profile chassis, remove the full height bracket and install the enhanced low profile bracket now. 1. Turn OFF the power to your computer and any other connected peripheral devices. 2. Unplug the power cord and remove the cover from the computer. 3. Remove the slot bracket from an available PCI Express slot. 2
4. To install the card, carefully align the card's bus connector with the selected PCI Express slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 5. Replace the slot bracket's holding screw to secure the card. 6. Replace the computer cover and reconnect the power cord. Driver Installation This section provides information on how to install the CyberParallel PCIe drivers. Windows 7 (32-/64-bit) Note: Windows 7 will automatically search preconfigured driver folders for the proper driver, this process may take several minutes to complete. Do not interrupt this process. 2. Right click Computer, click Manage, click Device Manager. 3. Insert the driver CD. Right click PCI Parallel Port, click Update Driver Software. 4. Click Browse my computer for driver software. 5. Type D:, then click Next. (Change D: to match your CD/DVD-ROM drive letter) 6. At Windows has successfully updated your driver software, click Close to complete the installation. Windows Vista (32-/64-bit) 3
2. At the Found New Hardware window, insert the driver CD, click Locate and install driver software (recommended), then click Continue. 3. Click Don't search online. Click Next. 4. Click Close to complete the installation. Windows XP (32-bit ) / Server 2003 (32-bit) 2. At the Found New Hardware Wizard, insert the driver CD. For XP w/sp1 or earlier / Server 2003: go to step #2. For XP w/sp2 or later / Server 2003 w/sp1 or later: select No, not this time, click Next. 3. Select Install the software automatically (Recommended, then click Next. 4. Click Finish to complete the installation. Windows XP (64-bit) / Server 2003 (64-bit) 2. At the Found New Hardware Wizard, insert the driver CD. For XP: go to step #2. For XP w/sp1 or later / Server 2003: select No, not this time, click Next. 3. Select Install the software automatically (Recommended, then click Next. 4. Click Continue Anyway, then click Finish to complete the installation. Windows Server 2008 (32-bit) 4
2. At the Found New Hardware window, click Locate and install driver software (recommended). 3. Insert the driver CD. 4. Click Don't search online. 5. Click I don't have the disc. Show me other options. 6. Click Browse my computer for driver software (advanced). 7. Type D:, then click Next. (Change D: to match your CD/DVD-ROM drive letter) 8. Click Close to complete the installation. Windows Server 2008 (64-bit) 2. At the Found New Hardware window, click Locate and install driver software (recommended). 3. Insert the driver CD. 4. Click I don't have the disc. Show me other options. 5. Click Browse my computer for driver software (advanced). 6. Type D:, then click Next. (Change D: to match your CD/DVD-ROM drive letter) 7. Click Close to complete the installation. Windows 2000 1. At the Found New Hardware Wizard, click Next. 2. Select Search for a suitable driver for my device (recommended), then click Next. 3. Check Specify a location, uncheck the other options and click Next. 4. Insert the driver CD, type in D:\2000, then click OK. (Change D: to match your CD/DVD-ROM drive letter) 5
5. Click Next, then click Finish to complete the installation. To Verify Windows Installation 1. Check in Device Manager to verify installation. For Windows 7: Right click Computer, click Manage, then click Device Manager. For Windows Vista: Right click Computer, click Manage, click Continue, then click Device Manager. For Windows XP / Server 2003 / 2000: Right click My Computer, click Manage, click Device Manager. For Windows Server 2008: Right click Computer, click Manage, double click Diagnostics, then click Device Manager. 2. Click on the + (plus sign) in front of Ports (COM & LPT), and a SIIG CyberPro Parallel port... should be displayed. Changing Parallel Port Number Some parallel port devices need a specific LPT in order to function properly. If your device works, do not make any changes. 1. Right click My Computer, click Manage, then click Device Manager. 2. Click on the + (plus sign) in front of Ports (COM & LPT), double click the SIIG CyberPro Parallel port you want to change. 3. Click the Port Settings tab. 4. Click the down arrow next to the LPT Port Number box, then select a parallel port that is not in use. 5. Click OK to save the changes. 6
Technical Support and Warranty QUESTIONS? SIIG s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a lifetime manufacturer warranty with this product. Please see our web site for more warranty details. If you encounter any problems with this product, please follow the procedures below. A) If it is within the store's return policy period, please return the product to the store where you purchased from. B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or replaced. Step 1: Submit your RMA request. Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA. Your RMA request will be processed, if the product is determined to be defective, an RMA number will be issued. Step 2: After obtaining an RMA number, ship the product. Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the original package must be included. Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton. You are responsible for the cost of shipping. Ship the product to the following address: SIIG, Inc. 6078 Stewart Avenue Fremont, CA 94538-3152, USA RMA #: SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no cost to the customer. 7
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio. All centered around the distribution and switching of A/V signals over CAT5/6, these products include matrix switches, distribution amplifiers, extenders, converters, splitters, cabling, and more. SIIG is the premier one-stop source of upgrades and is committed to providing high quality products while keeping economical and competitive prices. High-quality control standards are evident by one of the lowest defective return rates in the industry. Our products offer comprehensive user manuals, user-friendly features, and most products are backed by a lifetime warranty. SIIG products can be found in many computer retail stores, mail order catalogs, and e-commerce sites in the Americas, as well as through major distributors, system integrators, and VARs. PRODUCT NAME CyberParallel PCIe FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIIG, Inc. 6078 Stewart Avenue Fremont, CA 94538-3152, USA Phone: 510-657-8688 CyberParallel PCIe is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other names used in this publication are for identification only and may be trademarks of their respective owners. January, 2010 Copyright 2010 by SIIG, Inc. All rights reserved.