Why Use Filters of Filtered onnectors? Simple cost effective solution to help meet EMI/RFI compatibility requirements Best location for filtering is at the interface, which means inside the connector Easy add on or replacement to help meet your EMI performance Needs Helps reduce volume inside the unit as well as circuit board space Meets military standard and aerospace environmental requirements (MIL-STD-810, MIL-STD-461 and DO-160) Improves overall reliability due to fewer solder joints and few interconnections Parts are shipped 100% tested from the factory to insure proper performance and quality Flex Filter Inserts Drop-in filter solution for military circular and D-Subminiature connectors hip capacitor filtering with a wide array of capacitances and voltage ratings available Simple installation in your existing connector ost effective, providing simple and immediate solutions Filtered Military ircular onnectors D38999, M26482, M5015, M83723 Available with chip capacitor up through Pi filtering Available with solder cup, P tail and wired terminations Maximize your EMI filtering by customizing the filter on a pin by pin basis Filtered D-Subminiature and Micro-D onnectors Available with chip capacitor up through Pi filtering Many termination and hardware options available ustom configurations available ustom Filtering Solutions ustom EMI filtering and transient suppression modules Wide variety of filtering and transient protection available Special configurations with RJ-45 or USB terminations onsult factory for details
Types of Filtered onnectors and Their Performance 80 70 db 60 Insertion Loss 50 40 30 20 Pi, L, L apacitance Options Filter Performance hip apacitor 3 pf 47,000 pf+ >40 db Discoidal apacitor () 470 pf 40,000 pf+ 50 60 db Planar Array (L & L) 100 pf 1 uf+ 50 60 db Pi with Planar Arrays 100 pf 1 uf+ 70+ db Pi Tubes 47 pf 12,000 pf 70+ db L L Pi 10 hip L L L 0 10khz 100khz 1mhz 10mhz 100mhz 1ghz Frequency hip apacitor Filter Performance db Insertion Loss 45 40 35 30 25 20 15 10 5 10pF 0 10khz 100khz 1mhz 10mhz 100mhz 1ghz 47nF Frequency 10nF 4700pF 1000pF 470pF 100pF 22pF Shell Gasket hip ap Assembly Grounding Attachment Gasket Shell ontact Interfacial Seal Hard Faced Insert Pi Tube Assembly Descrete hip ap For Each Pin Oven ured Epoxy Potting Seal Flexible Substrate Hard Faced Insert Oven ured Epoxy Pi Filter onstruction with Planar Array Shell ontact Interfacial Seal Solder Insulators Grounding Ring Epoxy apacitors Inductors Pi Type Planar Array Assembly Grounding Ring Solder Washer or Spring lip Ground Electrode Hot Electrode Ferrite Inductor Filter ontact Assembly Ground Plate Interfacial Seal Pi Tube ontact Assembly Ground Electrode External Margin Solder Joint eramic apacitor Hot Electrodes Internal Margin Ferrite Inductor Solder Joint External Margin hip apacitor Filtering 40+ db Insertion Loss Quick Turn Lowest ost Option Limited High Frequency Performance, -L or L- Filtering Built with hip aps, Discoidals, Planars or Tubes 45-60 db Insertion Loss Good Broad Spectrum Filter Performance Pi Filtering Built with Pi Tubes, Discoidal or Planar Arrays Provides -L- omponent onfiguration Highest Performance: 70+ db Insertion Loss Very Good High Frequency Performance Termination Options: Solder up P Tail Wired terminations Other Options: ustom versions available including the ability to define the Filtering on a Pin by Pin basis to help eliminate as much noise as possible from your system ombination of filtering and transient suppression components available ustom applications and Filter Modules available to meet your special requirements
Filtered ircular Part Numbers Filtered onnectors F P 1A / 7 W / 15-35 S P - S 2-102 ONNETOR MIL ircular hip apacitor D Discoidal/Planar T Tubular apacitor P Pi Filter ONNETOR TYPE 1A MIL-DTL-38999 Series I 1B MIL-DTL-38999 Series II 1 MIL-DTL-38999 Series III 2A MIL-DTL-26482 Series 1 Solder 2B MIL-DTL-26482 Series 1 rimp 2 MIL-DTL-26482 Series 2 rimp 3A MIL-DTL-83723 Series III Bayonet 3B MIL-DTL-83723 Series III Threaded 4A MIL-DTL-26500 Bayonet 4B MIL-DTL-26500 Threaded 5A AS50151 Solder 5B AS50151 rimp Front 5 AS50151 rimp Rear ONNETOR STYLE 0 Wall Mount Receptacle 1 Inline Receptacle 2 Box Mount Receptacle 3 Box Mount Rear Panel Receptacle 4 Wall Mount Rear Panel Receptacle 5 Plug 6 Plug, EMI 7 Jam Nut Receptacle SHELL FINISH F Electroless Nickel W Olive Drab AD Other finishes available, consult factory APAITANE (3 DIGIT) VOLTAGE RATING (STEADY STATE) 0 50 VD 1 100VD 2 200 VD 3 300 VD 4 400 VD 5 500 VD For values over 500, consult factory FILTER LOATION S Shell Extension (As required) B Backshell ompatible ONTAT TERMINATION rimp P P Tail S Solder up W Wire Termination ONTAT GENDER P Male Pins S Female Sockets SHELL/INSERT ARRANGEMENT 15-35 17-26 23-21 Filter Inserts D38999 / 13-35 R - G 2-331 ONNETOR TYPE D38999 M26482 M5015 M83723 Other connector types available, consult factory INSERT ARRANGEMENT Shell size-insert arrangement ONNETOR STYLE P Plug R Receptacle G Filter with Install Guide GR RoHS ompliant with Guide APAITANE (3 DIGIT) VOLTAGE RATING 0 50 VD 1 100VD 2 200 VD 3 300 VD 4 400 VD 5 500 VD For values over 500, consult factory Please onsult the Factory for your Specific Part Number
Filtered D-Sub and Micro-D Part Numbers Filtered onnectors F D 09 M P - G 2-331 - 01 hip apacitor D Discoidal/Tubular apacitor P Pi Filter ONNETOR DENSITY D Standard D-Subminiature HD High Density D-Subminiature MD Micro-D NUMBER OF PINS Standard D-Subminiature 09, 15, 25, 37, 50 High Density D-Subminiature 15, 26, 44, 62, 78, 104 Micro-D 9, 15, 21, 25, 31, 37, 51, 69, 100, 122 GENDER M Male Pins F Female Sockets MF Male to Female Adapter TERMINATION P P Tail S Solder up W Wire I ID onnector 3.318 footprint Rt. Angle 5.590 footprint Rt. Angle OPTIONAL HARDWARE 01 Board Locks w/ Screw Lock HAN 02 w/ screw lock H/W 11 Board locks w/ threaded insert 12 w/ 4-40 threaded inserts onsult Factory for more options APAITANE (3 DIGIT) VOLTAGE RATING 0 50 VD 1 100VD 2 200 VD 3 300 VD 4 400 VD 5 500 VD For values over 500, consult factory OMPLIANE G Standard Filter R RoHS ompliant Filter Inserts D 09 - G 2-331 ONNETOR DENSITY D Standard D-Sub HD High Density D-Sub NUMBER OF PINS Standard D-Subminiature 09, 15, 25, 37, 50 High Density D-Subminiature 15, 26, 44, 62, 78, 104 APAITANE (3 DIGIT) VOLTAGE RATING 0 50 VD 1 100VD 2 200 VD 3 300 VD 4 400 VD 5 500 VD For values over 500, consult factory G Insert and Install Guide GR RoHS ompliant with Guide Please onsult the Factory for your Specific Part Number
EMI SOLUTIONS provides electro-magnetic interference (EMI) filtering solutions that help eliminate high frequency noise and high voltage transients. Our products include EMI filter inserts (Flex Filters), EMI Filtered onnectors and custom Filter Modules. Our engineering design team specializes in creating designs to effectively help you meet ommercial, Medical, Military or Aerospace EMI Requirements such as Mil-Std-461 or DO-160. ombined with our 24-hour availability and rapid turn-around times, EMI SOLUTIONS is your best source for filtering solutions. Headquartered in Irvine, alifornia, EMI SOLUTIONS was established in 1996 with a focus on specific niche products in the EMI Filtering business. Over the years, the company has grown and diversified into many related product lines. Through our experience and expertise in the EMI/ EM marketplace, we have become one of the leading manufacturers of Filtered onnectors for the Military, Aerospace, Medical and High Reliability ommercial applications. ontact EMI SOLUTIONS today and let our Engineering design team help you with your EMI issues. 949-206-9960 sales@4emi.com www.4emi.com 13805 Alton Parkway, Suite B, Irvine, A 92618