X5 Full-TOWER GAMING CASE X10 Double/Full-TOWER GAMING CASE User Manual
Contents 1.1 Specifications X5 3 1.2 Specifications X10 4 1.3 Accessory X5 & X10 5 1.4 Additional Accessory X10 5 2.1 Side Panel Disassembly 6 2.2 Motherboard Installation 7 2.3 5.25 Device Installation 8 2.4 External 3.5 Device Installation 9-10 2.5 2.5 HDD Installation 11 2.6 Power Supply Installation 12 2.7 Fan Installation 13-15 2.8 Water Cooling Installation 16 2.9 Supporting Feet Installation 17 2.10 Front I/O Installation Guide 18 3.1 Mini ITX Installation X10 19 3.2 Second Power Supply Installation X10 20 2
Chapter 1. Product Introduction 1.1 Specifications X5 Dimension Material Device & HDD 230(W)x 580(H)x 605(D)mm SECC Front Panel:ABS + Mesh Design 5.25 '' X 4(Exposed) 2.5 '' X 4(Hot Swappable Tray) 3.5 '' X 6(Hot Swappable Tray) 3.5 '' X 2(Hidden) Slot 10 Front I/O LED Indicator Cooling Fan Motherboard Power Supply USB3.0 2+USB2.0 4+ HD Audio Power & HDD Front:LED 120mm 2 (included) Rear:140mm 1 (included) Side:230mm x 1 or 120mm x 2 or 140mm x 2 Top: 230mm x 1 or 120mm x3 or 140mm x 2 Bottom: 230mm x 1 or 120mm x 2 or 140mm x 1 ITX, matx, ATX, E-ATX, XL-ATX, HTPX ATX 3
1.2 Specifications X10 Dimension 230(W)x 780(H)x 605(D)mm Material SECC Front Panel:ABS + Mesh Design Device & HDD 5.25 '' X 6(Exposed) 2.5 '' X 4(Hot Swappable Tray) 3.5 '' X 8(Hot Swappable Tray) 3.5 '' X 2(Hidden) Slot 10 Front I/O LED Indicator Cooling Fan Motherboard Power Supply Main Case: USB3.0 2 +USB2.0 4 + HD Audio Top System: USB2.0 2 + HD Audio Power & HDD Main Case: Front:LED 120mm 2 (included) Rear:140mm 1 (included) Side:230mm x 1 or 120mm x 2 or 140mm x 2 Top: 230mm x 1 or 120mm x3 or 140mm x 2 Bottom: 230mm x 1 or 120mm x 2 or 140mm x 1 Top System: Top: 230mm x 2 or 120mm x 4 or 140mm x 3 ITX, matx, ATX, E-ATX, XL-ATX, HTPX ATX (Main System) + SFX (Top System) 4
1.3 Accessory X5 & X10 - User Manual x 1 - Supporting Feet x 2 - Cable Tie x 5 - Screw Bag container the following screws: Standoff 5H-6#*4-6#*6.5HCu Screw 6*5KM Screw 3*5KM Screw 15PCS 32PCS 32PCS Screw Supply Screw M4*10 6#6HW-TC 6#*5B-C 8PCS 8PCS 19PCS 1.4 Accessory X10 Cover for the I/O slot if not used (Top System) Switching cable for connecting two ATX PSU to one motherboard Three different back plates for the top system 5
Chapter 2. Installation Guide 2.1 Side Panel Disassembly Remove the thumb screws from the rear side of the case and pull the side panel rearwards. To close again place the side panel into the guide rails and push it forwards with care, then screw in the two thumb screws on the rear side. X10 only: To open the side panel of the top unit, push the two indented handgrips inward to release the door. 6
2.2 Motherboard Installation Install the I/O panel that comes with your motherboard package. Secure the standoffs on the motherboard tray. Install the motherboard in proper location and secure it with provided screws. NOTE: CPU, RAM and any peripheral installation are not included in this manual. Please refer to your motherboard manual for related mounting instructions and troubleshooting. 7
2.3 5.25 Device Installation From the interior of the case, use a firm device of your choice to push the 5.25 drive bay cover out. Place the 5.25 device into the drive bay. Match the ODD drive holes with the drive cage. Then turn the knob clockwise to secure the drive cage. 8
2.4 External 3.5 Device Installation Open the front panel on the left hand side. Remove the hard drive tray by pushing the tray tab to the right to release the hard drive tray. Install hard drive by placing each individually into the hard drive tray. Secure each from the bottom of tray with the provided screws. 9
Place the tray back into to the case and lock it in place by pushing the tray in. The rear of the hard drive will connect to the backplane. Find the 4-Pin Molex on the power supply and connect it to the backplane. Connect the backplane to motherboard with SATA cable. X10 only: There are two more HDD trays at the top of the case. 10
2.5 2.5 HDD Installation Remove the 2.5 SSD hard drive tray by pushing the tray tab to the right to release the tray. Place 2.5 SSD hard drive into the hard drive box. Close the box. Slide the 2.5 SSD hard drive box to the end of drive cage. 11
2.6 Power Supply Installation Place the power supply in its proper location and secure it with the provided screws. Simply route the cables behind the motherboard tray and secure them with the provided cable tie. To optimize performance it is recommended that the washable dust filter underneath the power supply be cleaned on a regular basis. Simply pull out the dust filter, rinse with water, and slide it back after the dust filter is dried. 12
2.7 Fan Installation Fan Installation on the Side Panel Take out the dust filter from the side panel. Unscrew these three screws from the back of the side panel. Pull the plastic cover backward to remove the cover 13
Install the fan on the inside of the side panel and secure it from the outside of the panel with the provided screws. Up to two 120mm or two 140mm or one 230mm (in both directions) fans can be installed on the left side panel. Pull out the washable dust filter from the side panel for regular cleaning. 14
Bottom Fan Installation User can install 120mm x2, 140mm or 230mm x1 on the bottom panel. Top Fan Installation Remove the screws on the back of chassis and open the top panel. Install fans on the top and secure with the provided screws. Up to 120mm x3, 140mm x2 or 230mm x1 can be installed on top. X10only: Up to 120mm x 4 or 140mm x 3 or 230mm x 2 fans can be installed in the top unit. 15
2.8 Water Cooling Installation The pre-drilled water cooling holes at the case rear is for installing the external water cooling system. A 360 mm radiator may be installed on the top of chassis using the pre-drilled screw holes. X10only: A 480 mm radiator may be installed on the top plate using the pre-drilled screw holes. 16
2.9 Rubber Feet Installation Install Rubber foot on the proper position. Install supporting feet on the bottom with M4x10mm screws. 17
2.10 Front I/O Installation Guide X10 only: The unit comes with two sets of front ports: Front I/O ports for Top System Front I/O ports for Main Case Please refer to the following illustration of front I/O connector and your motherboard user manual. USB 3.0 USB 2.0 HD Audio 18
Chapter 3. Other Installation X10 only : The full tower comes with three different rear panels to meet the user s various needs. mini ITX back plate PSU back plate Fan back plate 3.1 Mini ITX Installation Install the I/O panel that comes with motherboard package. Install the power supply and the motherboard with the provided screws. 19
20
3.2 Second Power Supply Installation Unscrew and remove the rear panel from the back of the case. Install the PSU back plate in the rear with the provided screws. Install the power supply in the top unit. Connect the two power supplies with the provided PSU switching cable. 22
Streak Products, Inc. www.ultraproducts.com 2013 Streak Products, Inc. Ultra is a registered trademark and Ultra ETORQUE is a trademark of Streak Products, Inc. 8300 West Flagler Street, #121-106, Miami, FL 33144 All other trademarks listed are the property of their respective owners. Streak Products is not responsible for typographical or photographic errors. TECHNICAL SUPPORT (888) 222-5487 WARNING: Keep out of reach of children-contains sharp edges that may harm children. 22