VERO UK TRAINING MATERIAL

VERO UK TRAINING MATERIAL VISI Basic 2-D Modelling course (V-16)

VISI Modelling 2D Design Introduction Many component designs follow a similar route, beginning with a 2D design, part modelled using solids and commonly finished using surfacing techniques. The object of this course is to explain the basics of all methods. 2D Design 3D Solid Modelling Combined Solid & Surface Modelling Within this example we will use the drafting capabilities of VISI-Series to create a simple drawing. Vcamtech Co., Ltd 1

VISI Modelling 2D Design 2D Drawing Datum Point When you open the VISI-Series application for the first time you will be presented with the following interface: By default the working viewport will be setup to Dynamic. In this example we will only be working in 2D. Press the function key F2 to switch the viewport to the Top view mode. Vcamtech Co., Ltd 2

VISI Modelling 2D Design STAGE 1: CREATE THE OUTER SHAPE The first step is to produce some reference (construction) lines, which we will use as our datum reference for the complete 2D drawing. WIREFRAME SEGMENT/LINE PARALLEL When a command is selected a new set of icons will appear on the left hand side. These icons are only relative to the current command. The first two icons are very important. These two icons indicate which type of element will be created. If the Segment icon is selected a segment of a given length will be created. Example: A segment between two points: If the Line icon is selected a constructional line of infinite length will be created. These lines are generally used as a constructional aid to 2D drafting. In this instance we will create a constructional line parallel to the X and Y axis. (i) Select the Line icon (ii) Select the reference line - Select the X axis (iii) Select the distance 0mm Vcamtech Co., Ltd 3

VISI Modelling 2D Design Construction Line parallel to X axis Repeat the procedure for the Y axis. By default the system will retain the last command until the <ESC> key is depressed, there is no need to re-select the command from the menu. (i) Select the reference line - Select the Y axis (ii) Select the distance 0mm Construction Line parallel to Y axis We will use the newly created construction lines as the reference datum position for the 2D drawing. Vcamtech Co., Ltd 4

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select the X axis or the construction line following the X axis Arrow pointing above An arrow will appear indicating the side on which the line will be created. A minus value can be used to automatically change the side on which the line will be created. The SPACEBAR can also be used after the line has been created to toggle the creation side. (iii) Select the distance 180mm The line just created may not be instantly visible, this is because it has been created outside of the current viewing area. To make all elements visible select the include in boundary icon. Include all Vcamtech Co., Ltd 5

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select the Y axis or the construction line following the Y axis Arrow pointing left An arrow will appear indicating the side on which the line will be created. A minus value can be used to automatically change the side on which the line will be created. The SPACEBAR can also be used after the line has been created to toggle the creation side. (iii) Select the distance 275mm Again the construction line may not be visible. To make all elements visible select the include in boundary icon. Include all Vcamtech Co., Ltd 6

VISI Modelling 2D Design Using the Parallel command create two more construction lines. (i) (ii) Create a construction line parallel to Line 1 at a distance of 75mm (position left) Create a construction line parallel to Line 2 at a distance of 75mm (position below) WIREFRAME SEGMENT/LINE ELEMENT ELEMENT With the constructional base now created we can create the main outer shape of the 2D drawing. The Element Element command is used to create a segment or line between two points or elements. If the Points environment is selected a point (intersection point etc) can be selected. If the Element environment is selected geometrical elements can be selected. Vcamtech Co., Ltd 7

VISI Modelling 2D Design Points Environment : Point Environment Set Grid Parameters Sliding Insert the Point Coordinates Intersection Point Parametric Point on a Segment/Arc Quadrant of a Circle Enhanced Picking Enable / Disable Element Filter Project onto Current Workplane Select a Point with the Mouse Nearest Point in Polar Co-Ordinates Two Element Intersection Centre of a Circle / Arc Point Filter Equidistant Point Set / Cancel Filters Element Environment : Vcamtech Co., Ltd 8

VISI Modelling 2D Design (i) (iii) Select the Segment icon Make sure the Point environment is selected (iii) Make sure the Intersection Point icon is selected P2 P3 P4 P5 P1 P6 (iv) Select the start position - Select P1 Select the end position - Select P2 (v) Select the start position - Select P2 Select the end position - Select P3 (vi) Select the start position - Select P3 Select the end position - Select P4 (vii) Select the start position - Select P4 Select the end position - Select P5 (viii) Select the start position - Select P5 Select the end position - Select P6 (ix) Select the start position - Select P6 Select the end position - Select P1 Vcamtech Co., Ltd 9

VISI Modelling 2D Design In this example we have created a segment from each intersection point of the constructional geometry. It is possible to create the segments without the construction lines by using Cartesian co-ordinates to define the start and end points for each segment. It is also possible to use the EDIT BREAK DIRECT function to break a construction line and automatically create a segment. In this case, select the construction line to break where the segment needs to be created. A segment will be automatically generated between the first two intersection points. WIREFRAME SEGMENT/LINE DELETE ALL LINES Using this command we will delete all the construction lines to leave only the `component boundary. WIREFRAME SEGMENT/LINE CHAMFER Using this command we can add a chamfer to the 2D geometry and automatically trim the relevant segments. It is possible to define the chamfer using one of three options:- Distance :- The entered value will be used to chamfer both the selected elements. Distance Distance :- Two dimensional values can be added, to chamfer the selected elements at different distances. Distance Angle :- The first selected element will be chamfered at the First Distance value. The angle is controlled by the Angle value. It is also possible using the Retain Element check boxes to force the system not to automatically trim the geometry. Vcamtech Co., Ltd 10

VISI Modelling 2D Design (i) Select the first element - Select Segment 1 (ii) Select the second element - Select Segment 2 Select the Preview button to view the result. When you are happy with the result select the OK button or Right Hand Mouse Click to accept the result and close the chamfer dialog box Segment 1 Segment 2 WIREFRAME SEGMENT/LINE CHAMFER This time, we will create the chamfer using the Distance angle option. Check the Distance angle button. Set the distance to 20 and the angle to 45 (i) Select the first element - Select Segment 3 (ii) Select the second element - Select Segment 4 Segment 3 Segment 4 Vcamtech Co., Ltd 11

VISI Modelling 2D Design WIREFRAME CIRCLE/ARC FILLET Using this command we can add a fillet to the 2D geometry and automatically trim the relevant segments. Within the Fillet command it is also possible using the Retain Element check boxes to force the system not to automatically trim the geometry. Segment 2 Segment 3 Segment 1 Segment 4 Vcamtech Co., Ltd 12

VISI Modelling 2D Design (i) Select the first element - Select Segment 1 (ii) Select the second element - Select Segment 2 (iii) Select the first element - Select Segment 3 (iv) Select the second element - Select Segment 4 Segment 5 Segment 6 Segment 7 Segment 8 Now let s change the fillet radius value to 15mm and apply the fillet to Segment 5 and 6 and then apply a 10mm fillet to Segments 7 and 8. Vcamtech Co., Ltd 13

VISI Modelling 2D Design (v) Select the first element - Select Segment 5 (vi) Select the second element - Select Segment 6 Now add a fillet to Segments 7 and 8 setting the radius value to 10mm. (vii) Select the first element - Select Segment 7 (viii)select the second element - Select Segment 8 Segment 1 Segment 2 With the outer shape now completed we can concentrate on constructing the inner detail Vcamtech Co., Ltd 14

VISI Modelling 2D Design STAGE 2: CREATE THE INNER TRIANGULAR DETAIL WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select Segment 1 An arrow will appear indicating the side on which the line will be created. A minus value can be used to automatically change the side on which the line will be created. The SPACEBAR can also be used after the line has been created to toggle the creation side. (iii) Select the distance 50mm (position right - SPACEBAR) NOTE!. If at any point, the Insert the distance panel does not appear, click on this Distance icon to make it appear. WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select Segment 1 An arrow will appear indicating the side on which the line will be created. A minus value can be used to automatically change the side on which the line will be created. The SPACEBAR can also be used after the line has been created to toggle the creation side. (iii) Select the distance 150mm (position right - SPACEBAR) Vcamtech Co., Ltd 15

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select Segment 2 An arrow will appear indicating the side on which the line will be created. A minus value can be used to automatically change the side on which the line will be created. The SPACEBAR can also be used after the line has been created to toggle the creation side. (iii) Select the distance 15mm (position above - SPACEBAR) P1 Reference line (L1) Vcamtech Co., Ltd 16

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE ELEMENT ANGLE LINE Having created the construction lines, we have generated the intersection points at which the 45 construction lines need to be struck through. (i) (ii) Select the Line icon Make sure the Point environment is selected (iii) Make sure the Intersection Point icon is selected (iv) Select the reference point - Select (P1) (v) Select the reference element - Select the reference line (L1) NOTE! An arrow will be displayed at the point you select the reference element. Confirm the reference element direction with a Right Hand Mouse Click (vi) Insert the angle - 45 NOTE: With most CAD systems, the angles are calculated with 3 O clock being zero and positive degrees are in the anti-clockwise direction. Within the VISI-Series applications the selected line or axis becomes zero degrees and the SPACEBAR can be used to toggle the resultant line between plus or minus angles. WIREFRAME SEGMENT/LINE ELEMENT ANGLE LINE Having created the construction lines we have generated the intersection points at where the 45 construction lines need to be struck. (i) (ii) Select the Line icon Make sure the Point environment is selected (iii) Make sure the Intersection Point icon is selected Vcamtech Co., Ltd 17

VISI Modelling 2D Design (iv) Select the reference point - Select (P2) (v) Select the reference element - Select the reference line (L1) (vi) Confirm the Reference element direction - Right Mouse Click (vii) Insert the angle 45 SPACEBAR to toggle the result P2 Construction Line - L1 When we created the outside shape for the component, we created a segment between each intersection point. It is also possible to use the EDIT BREAK DIRECT function to break a construction line and automatically create a segment. In this case, select the construction line to break where the segment needs to be created. A segment will be automatically generated between the first two intersection points. The spacebar can be used to toggle the result. Vcamtech Co., Ltd 18

VISI Modelling 2D Design EDIT BREAK DIRECT (i) Select the element to break - Select Construction Line (C1) Where indicated Select the construction line to break in-between the two intersection points from which the segment will be created. (ii) Select the element to break - Select Construction Line (C2) Where indicated (iii) Select the element to break - Select Construction Line (C3) Where indicated C1 C2 C3 The result of the Break Direct should be as shown. Segment 2 Segment 1 Segment 3 Vcamtech Co., Ltd 19

VISI Modelling 2D Design WIREFRAME CIRCLE/ARC FILLET Using this command we can add a fillet to the 2D geometry and automatically trim the relevant segments. Within the Fillet command it is also possible using the Retain Element check boxes to force the system not to automatically trim the geometry. (i) Select the first element - Select Segment 1 Select the second element - Select Segment 2 (ii) Select the first element - Select Segment 2 Select the second element - Select Segment 3 (iii) Select the first element - Select Segment 3 Select the second element - Select Segment 1 NOTE: It is also possible when adding a fillet or chamfer to select only the intersection point rather than the two intersecting elements. A2 A1 A3 Vcamtech Co., Ltd 20

VISI Modelling 2D Design WIREFRAME CIRCLE/ARC CENTRE RADIUS Using this command we can add the circular holes to the inside of the triangular slot. (i) Ensure the Circle Centre icon is selected (ii) Select the centre point - Select Arc (A1) (iii) Enter the Radius value 5mm (iv) Repeat for centre point position 2 and position 3 - (A2) & (A3) ANNOTATION CROSS We can use this command to automatically create the centre line cross at the centre of any arc or circle within the drawing. By default the system will select both arcs and circles as they are both enabled within the left hand icon set. (i) Switch OFF the arc selection from the left hand icon set Default Settings Both arcs and circles selected Switch OFF the arc selection Vcamtech Co., Ltd 21

VISI Modelling 2D Design (ii) Use the Select all window filter to select all circles within the 2D drawing. Select All (iii) Select the cross angle 0 STAGE 3: CREATE THE INNER T-SLOT DETAIL Segment 1 Construction Line - C1 Vcamtech Co., Ltd 22

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE PARALLEL Now we have created the triangular form we can continue to create the T slot holes. (i) Select the Line icon (ii) Select the reference line - Select Segment 1 (iii) Select the distance 50mm (position below - SPACEBAR) WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select Construction Line 1 (C1) (iii) Select the distance 15mm (position right - SPACEBAR) WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select Construction Line 1 (C1) (iii) Select the distance 15mm (position left) Vcamtech Co., Ltd 23

VISI Modelling 2D Design Construction line 2 (C2) WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select Construction Line 2 (C2) (iii) Select the distance 30mm (position above) Vcamtech Co., Ltd 24

VISI Modelling 2D Design Using the construction lines we have created the centre positions for the 5mm radius circles. WIREFRAME CIRCLE/ARC CENTRE RADIUS (i) Make sure the Intersection Point icon is selected (ii) Select the centre point - Select Centre Point 1 (P1) (iii) Enter the Radius value 5mm (iv) Repeat for centre point position 2 and position 3 - (P2) & (P3) Vcamtech Co., Ltd 25

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE ELEMENT ELEMENT (i) Select the Segment icon (ii) Make sure the Element environment is selected (iii) Select the first element - Select Circle 1 (top) (iv) Select the second element - Select Circle 2 (top) NOTE : The selection point of the circle is very important. The segment being created will be struck tangent from the circle at the closest point to the selection position. In all cases the SPACEBAR can be used to toggle the result Example : If both circles are selected close to the top this will be the result If one circle is selected close to the top and the other close to the bottom this will be the result WIREFRAME SEGMENT/LINE ELEMENT ELEMENT (i) Select the Segment icon (ii) Make sure the Element environment is selected (iii) Select the first element - Select Circle 1 (bottom) (iv) Select the second element - Select Circle 2 (bottom) Vcamtech Co., Ltd 26

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE ELEMENT ELEMENT (i) Select the Segment icon (ii) Make sure the Element environment is selected (iii) Select the first element - Select Circle 3 (Left hand side) (iv) Select the second element - Select Segment 1 WIREFRAME SEGMENT/LINE ELEMENT ELEMENT (i) Select the Segment icon (ii) Make sure the Element environment is selected (iii) Select the first element - Select Circle 3 (Right hand side) (iv) Select the second element - Select Segment 1 Vcamtech Co., Ltd 27

VISI Modelling 2D Design WIREFRAME SEGMENT/LINE DELETE ALL LINES Using this command we will delete all the construction lines used in the creation of the T- slot. Circle - (C3) Segment - (S1) Circle - (C1) Circle - (C2) Vcamtech Co., Ltd 28

VISI Modelling 2D Design EDIT BREAK DIRECT (i) Select the element to break - Select Circle 1 (C1) Where indicated (ii) Select the element to break - Select Circle 2 (C2) Where indicated (iii) Select the element to break - Select Circle 3 (C3) Where indicated (iv) Select the element to break - Select Segment 1 (S1) Where indicated Vcamtech Co., Ltd 29

VISI Modelling 2D Design EDIT TRANSLATION As the T-slot forms are exactly the same we can create a copy of the T-slot already created without having to reconstruct each T-slot form. Multiple copy (i) Select the multiple copy icon Number of copies 2 (ii) Select the elements to copy - Create a selection window by simply moving your curser to the window start point and with your LHM button pressed down drag a selection box around the element to copy. Finish the selection by releasing the mouse button. Window Start Point Elements to COPY Release Mouse Button to make window selection (iv) Select the reference point for translation Incremental Translation icon - Select the Incrementele translatie Vcamtech Co., Ltd 30

S1 VISI Modelling 2D Design WIREFRAME SEGMENT/LINE PARALLEL (i) Select the Line icon (ii) Select the reference line - Select Segment Line 1 (S1) (iii) Select the distance 60mm (position below) Reference point for mirror operation Vcamtech Co., Ltd 31

VISI Modelling 2D Design EDIT MIRROR With the 3 T-slot forms created we can use the Mirror command without having to reconstruct the T-slot shape. Again, as we are making a copy it is important to have the Copy icon switched ON. Copy icon (i) Select the elements to mirror - Using a selection window, select all the elements that create the 3 T-slot forms (ii) Select the reference point - Select the Intersection Point icon (iii) Select the mirroring axis - Select the X axis icon (iv) Confirm the resulting mirror - RHM click to accept the results of the mirroring Vcamtech Co., Ltd 32

VISI Modelling 2D Design STAGE 4: CREATE THE SET OF HOLES When there are a number of elements equally positioned, we can create a matrix grid and apply a set of elements to that grid. The entire grid can then be treated as a group of elements. This functionality is often used with drilling cycles. WIREFRAME SET OF POINTS MATRIX (i) Select the application point - Using the Cartesian Co-ordinate icon select the application point X-80, Y25, Z0 Insert the Point Coordinates (ii) Define the Matrix parameters No. of base points 4 Distance between points 20 Base angle 0 No. of vertical points 3 Distance between points 20 Vertical angle 90 Vcamtech Co., Ltd 33

VISI Modelling 2D Design Set of points As the hole detail has already been created inside the triangular slot, we can use the same hole geometry, and copy it onto the set of points WIREFRAME SET OF POINTS COPY ONTO SET (i) Select the set of points on which to copy - Select the set previously created (ii) Select the elements to copy - Select the geometry of one hole ( Circle & Circle centre cross ) NOTE : If selecting more than one entity, it is possible to both select the geometry using a window or selecting the Block control icon and selecting manually the elements to copy. It is also possible to keep the <CTRL> key depressed when manually selecting elements. This will work in exactly the same way as the Block control icon. Vcamtech Co., Ltd 34

VISI Modelling 2D Design (iii) Select the application point - This will be the point at which the geometry being copied will be positioned on the set. (iv) Make sure the Circle Centre icon is selected (v) Select the centre point - Select Centre Point 1 (P1) Vcamtech Co., Ltd 35

VISI Modelling 2D Design STAGE 5: ANNOTATE THE DRAWING When trying to annotate a drawing there are many methods possible to show each dimension. Following is an explanation of each dimension type : 1) Single Element : This linear dimension can be defined parallel to the X axes, to the Y axes, or to the direction of a reference element joining the two reference POINTS or ELEMENTS 2) Angular Dimension : This command creates an angular dimension between two segments or lines or between a segment/line and an axis reference. 3) Datum Dimension : Generates a series of linear dimensions referenced from a common datum position and separated from each other by a user-defined distance (pitch). 4) Aligned Dimension : Generates a series of aligned spatial linear dimensions. The first dimension is generated as though it where a linear spatial dimension parallel to a line, segment or an axis. Subsequent dimensions are generated automatically by selecting one point. Each dimension will be physically aligned with the first. 5) Ordinate Aligned : Generates a series of aligned spatial linear dimensions. The first dimension is generated as though it where a linear spatial dimension parallel to a line. Subsequent dimensions are generated so that each dimension is physically aligned with the first. Each dimension generated is a continuation of the last but with the same origin coincident with the first selected point and positioned on the same axis 6) Ordinate Positional : Vcamtech Co., Ltd 36

VISI Modelling 2D Design Generates a series of linear dimensions referenced from a same origin and separated from each other, along a reference direction by a defined distance (pitch). 7) Diameter in Section : Lets you include radial/diameter dimensions on sectional or side views of a part. It is commonly used, for example, in the dimensioning of turned parts. 8) Arc Length Dimension : Creates the dimension for the length on an arc. The dimension can be represented in two different ways: The first shows the length of the selected arc, the second shows the width of the arc. 9) Edit Dimension : Allows you to modify and/or move one or more dimensions or text leaders that have previously been created. 10) Local Dimension Parameter: Allows the setting of default dimension parameters within this workfile only. 11) Text : Allows you to enter a text note onto the drawing. 12) Edit text : Allows you to modify an existing text note. 13) Text Leaders : Allows you to create a 2 (up to 4) point text leader. 14) Text Balloon : Allows you to create a 2 (up to 4) point text balloon. 15) Quick hatch : Allows quick cross hatching within a closed boundary. 16) Extended Circle: Allows you to create a hole chart table 17) Circle Dimension : Allows you to create a series of XY positions around any circle or arc Vcamtech Co., Ltd 37

VISI Modelling 2D Design 18) Point Dimension : Allows you to create a series of XYZ text box s from a relative point 19) Extended Baloons Dimension : Allows you to create a point chart relative to balloon positions Point - (P1) Point - (P2) ANNOTATION SINGLE ELEMENT The dimensioning works using the Points environment and the Element environment for selection. If the Points environment is active a dimension can be struck from two points. If the Element environment is active only the single element needs to be selected to obtain the dimension. (i) (ii) Make sure the Point environment is selected Make sure the Intersection Point icon is selected (iii) Select the first intersection point - Select point 1 (P1) (iv) Select the second intersection point - Select point 1 (P2) Vcamtech Co., Ltd 38

VISI Modelling 2D Design As the two selected points are not orthogonal the dimension will be automatically set to be direct. Using the icons available on the left hand side of the graphical area, select the Horizontal Dimension icon. Horizontal Dimension Segment S1 Segment S2 Vcamtech Co., Ltd 39

VISI Modelling 2D Design ANNOTATION ANGULAR DIMENSION The dimension type works using the Element environment for selection. (i) Select the first reference element - Select segment 1 (S1) (ii) Select the second reference element - Select segment 2 (S2) (iii) Moving the mouse into the different angle quadrants will produce a different result. Select the one required. Fillet 1 (F1) Vcamtech Co., Ltd 40

VISI Modelling 2D Design ANNOTATION SINGLE ELEMENT (i) Make sure the Element environment is selected (ii) Select the element - Select Fillet 1 (F1) Using what we have learned try to fully dimension the drawing in a similar fashion to the original specification (Page 8). Vcamtech Co., Ltd 41

VISI Modelling 2D Design Here are some examples for you to work through. Please add the dimensions as shown on the drawings. Example 1 2D Clip Using what we have learnt try to create this simple clip. This drawing will be required later within the VISI-Modelling training course. Save the file using: - FILE SAVE AS then change Save as type to VISI Symbols (*.sym) Symbols would normally be stored in the <Install Point>\Cad\Symbolf folder. Ask your tutor to explain about Symbols Vcamtech Co., Ltd 42

VISI Modelling 2D Design Example 2 Vcamtech Co., Ltd 43

VISI Modelling 2D Design Example 3 Vcamtech Co., Ltd 44

VISI Modelling 2D Design Example 4 Vcamtech Co., Ltd 45

VISI Modelling 2D Design Example 5 Vcamtech Co., Ltd 46

VISI Modelling 2D Design Example 6 Vcamtech Co., Ltd 47

VERO UK TRAINING MATERIAL V16 Component Modelling Using Solid Primitives

VISI Modelling Primitive Pre requisite To complete this tutorial the user must have a general understanding of the VISI interface and system operation, and must also have completed the 2D Drafting Tutorial and exercises. Objectives The purpose behind this exercise is to use VISI Modelling to construct a basic component part by creating and manipulating the Standard Primitive Solids. The tutorial will introduce the basics of creating different types of primitives, how to combine them to create more advanced solids and how to use some of the solid editing tools to further enhance the solid forms. The part that will be created is shown below. Vcamtech Co., Ltd 1

VISI Modelling Primitive PRIMITIVE MODELLING EXAMPLE 1 STEP 1: Create the base cuboid. Solid Forms - Cuboid Cuboid Centre of Rectangle Insert point coordinates Select the OK button. Specifiy the cuboid dimensions: Dialogue Box data Input Insert the dimensions and click OK. Resulting cuboid. Vcamtech Co., Ltd 2

VISI Modelling Primitive STEP 2: Make a second cuboid to define the vertical section. Solid Forms - Cuboid Cuboid Bottom left corner Create with Subtraction. Select Intersection Point here. Intersection point Define the cuboid dimensions: Dialogue box data input Insert the dimensions and click OK. Vcamtech Co., Ltd 3

VISI Modelling Primitive STEP 3: Make the third cuboid. Select Intersection Point here. Solid Forms - Cuboid Cuboid Bottom left corner Intersection point Define the cuboid dimensions Dialogue box data input Insert the dimensions and click OK. Vcamtech Co., Ltd 4

VISI Modelling Primitive STEP 4: Blend the edges of the third cuboid. Operation - Blends Select these 2 vertical edges. Select Single Edge Blends Block control for multiple selection. Insert the blend parameters as shown below and click OK. Vcamtech Co., Ltd 5

VISI Modelling Primitive STEP 5: Unite the three solids together. Operation - Unite Unite Select the base cuboid as the Target body Click Select All to unite the 2 other remaining solids to the target body. STEP 6 : Make the strengthening web using another Cuboid. Solid - Forms - Cuboid Cuboid Bottom left corner Create with Unite Parametric point on segment/arc Select the edge on the solid as shown here Vcamtech Co., Ltd 6

VISI Modelling Primitive Select the option Distance and insert the distance 19 as shown. Define the cuboid dimensions. Dialogue box data input STEP 7: Create a Chamfer Operation Chamfer Insert the dimensions and click OK. Chamfer Select single edge Select the horizontal edge on the new cuboid as shown here. Vcamtech Co., Ltd 7

VISI Modelling Primitive Input the Chamfer parameters as shown opposite and then click OK STEP 8: Make a rectangular slot in the base block. Solid - Forms - Cuboid Cuboid Bottom left corner Create with Subtraction Parametric point on segment/arc Select the option Distance and insert the distance of Vcamtech Co., Ltd 15mm 8

VISI Modelling Primitive Select the option Distance and insert the distance of 15mm Input the dimensions for the cuboid. Dialogue box data input Input the dimensions and click OK. STEP 9 Blend the 2 vertical edges of the slot cuboid. Operation - Blends Select the 2 vertical edges. Select Single Edge Blends Block control for multiple selection. Vcamtech Co., Ltd 9

VISI Modelling Primitive Insert the Blend parameters as shown below and then select OK. STEP 10: Create a cylinder on the top of the main body. Solid Forms - Cylinder Cylinder Create with Unite Select the circular edge of the solid as shown. Centre of a circle/arc Vcamtech Co., Ltd 10

VISI Modelling Primitive Define the cylinder properties. Dialogue Box data Input Input the radius and height and select OK. Resulting cylinder STEP 11: Create the round hole through the cylindrical feature. Solid Forms - Cylinder Cylinder Create with Subtraction Centre of a circle/arc Select the circular edge of the solid as shown. Vcamtech Co., Ltd 11

VISI Modelling Primitive Input the parameters for the cylinder: Dialogue Box data Input Input the values and select OK. Resulting cylinder. STEP 12 : Blend some of the edges on the solid model. Operation - Blends Select Single Edge Select this edge Block control for multiple selection. Vcamtech Co., Ltd 12

VISI Modelling Primitive Insert the Blend radius value As shown and then click OK. Insert the blend parameters as shown below. Pick the edges as shown opposite. Select these 2 edges. Insert the blend parameters as shown below. Pick the edges as shown opposite. Select this edge. Insert the blend parameters as shown below. Pick the edges as shown opposite. Select this edge and the one on the opposite side. Vcamtech Co., Ltd 13

VISI Modelling Primitive In this case select the option Propagate over tangent edges which will enable the blend rad to flow along all the tangent edges between the web and main body. The Result are shown below. STEP 13 : Find the volume of the solid body.? - Query Query Solid properties Select the solid body. Select YES at the following dialogue box. Vcamtech Co., Ltd 14

VISI Modelling Primitive Here you can evaluate various properties of the solid model (external area, volume, centre of gravity, minimum convex radius, minimum concave radius) Volume (cubic mm) That completes the step by step example no.1 Vcamtech Co., Ltd 15

VISI Modelling Primitive PRIMITIVE MODELLING EXAMPLE 2 Vcamtech Co., Ltd 16

VISI Modelling Primitive STAGE 1 : Start by creating a solid Cuboid to act as a starting base for the component. Pick Cuboid Use Value shown Pick Centre Placement Now enter the cube sizes Pick Dialogue Box Input Enter Cube Parameters The finished Cuboid STAGE 2 Add a Cylinder to the underside of the Cuboid base Pick Cylinder Use the values shown Use Co-ordinate Input Vcamtech Co., Ltd 17

VISI Modelling Primitive Define the size of the Cylinder Pick Dialogue Box Input Enter the Cylinder Parameters The finished cylinder primitive 2.1 Add the cylinder and Cuboid together to make one solid body Operation > Unite [Pick the Cuboid] [Pick the Cylinder] Target Body Body to unite STAGE 3 Create a Slot running through the cylinder from front to back. Pick Central Positioning Pick Cuboid Locate the Cuboid at the Centre of Circle Pick Centre of this Circle as Shown Vcamtech Co., Ltd 18

VISI Modelling Primitive Define the Cuboid parameters and make it automatically cut away from the cylinder. Pick Dialogue Box Input Pick Create with Subtraction Define the Cube sizes You will see the Slot appear automatically New slot position subtracted automatically STAGE 4 Create the first of the 2 locating lugs on the top of the Cuboid base primitive Pick bottom left corner positioning Pick Cuboid Use co-ordinate input and use the parameters shown Vcamtech Co., Ltd 19

VISI Modelling Primitive Define the size of the Cube Pick dialogue box input Enter the Cube dimensions The resulting Cube primitive is shown below Newly created Cube which will form the first lug Note :- This Cube is not yet joined to the rest of the solid body 4.1) Adding the Hole into the newly created Cube To create a hole in the correct direction the select direction icon will have to be activated to choose the Y orientation. Now create the cylinder for the hole feature Pick Cylinder Use Automatic Subtraction Use Select Direction icon Use Co-ordinate Input Use Co-ordinates shown Vcamtech Co., Ltd 20

After inserting the co-ordinates you must now select the Y axis icon. VISI Modelling Primitive Select the Y axis icon to make sure the cylinder runs along the Y direction. Reverse the direction of the Y axis, so that the arrow on screen is pointing along the negative Y direction. Define the parameters for the Cylinder Click Dialogue Box input Enter Cylinder Parameters Newly created Hole Feature Vcamtech Co., Ltd 21

VISI Modelling Primitive 4.1 Round the corners of the cuboid to finish the lug feature. Operation > Blends Click Single Edge Blending Pick these 2 edges Use Block control to allow multiple edges to be picked Input the Blend value as shown The finished Lug should look similar to the diagram below The Result of the 2 blended edges Note :- The Lug is not joined to the rest of the solids yet so that an identical copy can be made Vcamtech Co., Ltd 22

VISI Modelling Primitive 4.2 Create the second lug by creating an identical copy of the first. This can be done by simply Mirroring the original lug as a copy. Edit > Mirror Click the Copy Icon Select the element to mirror Select the lug Make sure Mirror 2D is showing Pick Coordinate input Choose to Mirror with the X axis You will now have a wire frame preview of the mirrored lug, simply select the right mouse button to confirm the mirror operation. The model should look like the diagram opposite with the mirrored copy of the lug Vcamtech Co., Ltd 23

VISI Modelling Primitive STAGE 5 Unite the 2 lug solids to the rest of the body Operation > Unite Pick the base solid as the Target body Then pick Select All to join the remaining solids to the base STAGE 6 Add some extra thickness to the floor between the 2 lugs by simply moving the face upwards Modelling > Move a face Pick Select by Face icon Select the face between the two lugs Vcamtech Co., Ltd 24

VISI Modelling Primitive Input the distance value as shown Floor has been raised by 2 mm STAGE 7 Add the finishing touches to the model by adding some Blends to the sharp edges Operation > Blends Click Single Edge Blending Use Block control to enable multiple edges to be picked Pick these 4 edges Vcamtech Co., Ltd 25

VISI Modelling Primitive Add the Blend Value as shown NOTE! Make Sure the Propagate over tangent edges is selected. This allows the blend to follow around any connected tangent edges The result of the Blends. Note how the Blends follow around the tangent edges Add a Blend to the joining edge of the main Cylinder and the Base Cube Click Single Edge Blending Pick this edge to add Blend Add the Blend Value as shown The applied 3mm Blend Vcamtech Co., Ltd 26

VISI Modelling Primitive STAGE 8 Add 4 chamfers to each of the 4 edges of the holes Operation > Chamfer Pick Single Edge Selection Edges 3 and 4 Edges 1 and 2 Use Block Control Insert the Chamfer Parameters The final solid with the Chamfers applied That completes the step by step example no.2 Vcamtech Co., Ltd 27

VISI Modelling Primitive ADDITIONAL TASKS To demonstrate that you have understood the basic principles of Primitive Solid modelling try to create the following components using primitive modelling techniques. Exercise 1 Vcamtech Co., Ltd 28

VISI Modelling Primitive Exercise 2 Ask the tutor to explain Feature Manager Vcamtech Co., Ltd 29

VISI Modelling Primitive Exercise 3 Vcamtech Co., Ltd 30

VERO UK TRAINING MATERIAL How and why to use profiles in Visi Modelling

Pre requisite VISI Modelling Profile To attempt this course it is required that you have completed the 2D Drafting tutorial and exercises and have successfully finished the Basic Modelling guide. Objectives It soon becomes apparent that modelling with primitives can only be useful for creating very basic and simple shapes. To create irregular and more complex solid shapes is not practical with basic solid forms. To overcome this problem it is more suitable to create and use Profiles. In their commonest forms Profiles come in 2 distinct types, Closed profiles and Open Profiles. In this tutorial both types will be demonstrated to show how they can be applied to creating more complex solid and surface geometry. To do this you will need to draw the following 2D geometry: - Closed Profile Example Drawing Tip: - It only requires 3 commands to create this contour: - 1. Circle/Arc-Centre Radius 2. Circle/Arc-Element Element Radius 3. Break direct Vcamtech Co., Ltd 1

VISI Modelling Profile STAGE 1 Draw the 2D elements on previous page Closed Profiles by definition are a continuous chain of 2D elements where the chain forms a closed loop. As a rule, the elements that form the closed loop must all touch at their endpoints. If you consider the geometry you have drawn, this type of shape would be very impractical to create using basic solid primitives. How do you create a solid from these 2D elements? Extruding Profiles as Solids Extruding Profiles into Solids is one of the most convenient ways of creating irregular solid forms. To begin with, the 2D elements need to be made into a Profile. Click on Closed Profile Click on an element to begin Profile Creation. The arrow indicates the chaining direction of the profile. From the Left hand screen menu, icons can be selected to vary the way in which the profile is created. Changes the Tolerance of the allowable gap between connecting elements Undo the last selected element in the profile Create blends on sharp corners of a profile Erases original 2D elements. Inverts blends on a profile Automatically chains the elements Vcamtech Co., Ltd 2

VISI Modelling Profile Automatically chain the elements and erase underlying geometry Erase original 2D elements. Pick first Automatically chain the elements At the prompt select Yes The 2D elements should now have been erased and the display should show a YELLOW profile. Now Extrude the Profile into a solid. Modelling > Extrude elements Arrow Indicates Extrusion direction Extrude in the Z Direction Extrude the Profile with the Parameters shown Vcamtech Co., Ltd 3

VISI Modelling Profile The resulting solid should look like the diagram opposite. As you can see, this type of solid would be virtually impossible using primitives alone. STAGE 2 Extra uses for Profiles with solids Now that a solid has been created, a Profile can be directly extracted from a Face of a solid. For this example use the solid you have just created. Create profile from a soild face. Pick top face of solid Profile From Face Use the parameters as shown. A profile will now be created on this top face. Vcamtech Co., Ltd 4

VISI Modelling Profile Now offset this profile inwards to create another new Profile. Offset Profile Arrow indicates direction of offset, use space bar to toggle direction Input the Parameters shown The display shows the offset profile Use the 2mm Offset Profile to create a pocket into the Solid. Operation > Pocket From Profile 1) Pick the solid 2) Pick the Offset Profile Vcamtech Co., Ltd 5

VISI Modelling Profile Enter the parameters for the Pocket Enter the height parameter as shown. As long as the profile lies on the solid face a positive height value will always pocket into a solid regardless of axis direction The resulting solid should resemble the display below. It can be seen from the previous exercises that Profiles can create many possibilities for more complex solid forms. However profiles are not just limited to extrusions. They can be revolved to create other solid forms, as the next exercise will demonstrate. Vcamtech Co., Ltd 6

VISI Modelling Profile STAGE 3 Swinging a Closed Profile Consider the 2D profile you created in the first example and position it as shown in the diagram below (i.e. Translate it 200mm in Y ). Pick the Closed Profile shape and position it 200mm from the origin axis Origin Axis Now Revolve this Profile around the Axis shown Modelling > Swing > Swing Elements Pick the the Closed Profile shape Pick Co Ordinate input Pick the X axis for the axis of revolution Check the work plane button and use the values shown. Vcamtech Co., Ltd 7

VISI Modelling Profile Enter the angle that the profile will be swung through. Use the Parameters shown The resulting display should resemble the diagram below. It can be seen that, using a combination of Extrusion and Swing, Closed Profiles can result in numerous solid forms. These combined with Solid Primitives enable many different Solid models to be constructed. But what happens in the case of an Open Profile? Vcamtech Co., Ltd 8

VISI Modelling Profile STAGE 4 Creating Open Profiles Open Profiles by definition are a continuous chain of 2D elements where the first and last elements in the chain are not coincident. As a rule the elements that form the chain must all touch at their endpoints except the first and last element endpoints. Construct the 2D elements in the drawing shown below. There is no need to add the dimensions. Construct an Open Profile from this set of 2D elements 2) Pick End Element Pick Open profile 1) Pick Start Element Vcamtech Co., Ltd 9

VISI Modelling Profile Choose to erase the existing 2D elements and Automatically chain the geometry. Erase original 2D elements. Pick first Automatically chain the elements Click yes to confirm the Profile The open set of 2D elements should have now been replaced by a YELLOW Open Profile. Things To Try 1) Try extruding the the Open Profile in exactly the same way as you did in the Closed Profile exercise. How does it differ from the Closed Profile result? 2) Swing the Open Profile around the default X axis. No profile repositioning is required. Swing the Profile through 360 degrees and take note of the obtained result. How would you make a Solid body from the result? 3) Use Edit > Dissolve Aggregates on the yellow profile to turn it back into segments and arcs. Now extrude all the segments and arcs the same as you did in 1) above. How does the result differ from those obtained at 1) above? Now you have explored some of the possibilities with Open and Closed Profiles, try the following unassisted exercises which will require profile creation to successfully complete the models. Vcamtech Co., Ltd 10

VISI Modelling Profile EXERCISE 1 Create this component using a combination of swing and extruded profiles along with primitives. Vcamtech Co., Ltd 11

VISI Modelling Profile EXERCISE 2 Create this component using a combination extruded profiles along with primitives Vcamtech Co., Ltd 12

VISI Modelling Profile EXERCISE 3 Create this component using extruded profiles along with primitives Vcamtech Co., Ltd 13

VERO UK TRAINING MATERIAL VISI Modelling Layers

VISI Modelling Layers Introduction Layers are an important part of the software and are used extensively throughout the day to day running of the software. Layers allow us to group together many items (geometry, solid, surfaces etc) and put them onto different layers to make the viewing of the data much easier. Layers can be either visible or not, and this will make working with both small and large files much easier to understand. Vcamtech Co., Ltd 1

VISI Modelling Layers Open the file Layer Management.wkf On the file just opened there are many different elements, dimensions, solids and surfaces and also many different colors of elements. At present all elements are on one layer and only one layer is present. Vcamtech Co., Ltd 2

VISI Modelling Layers 1 2 3 4 5 6 7 8 1. Change Attribute This allows the user to change the properties of one or more selected entities. This can include: - layer, color, line style and transparency value 2. Set Drawing Filters Here is where layers or elements can be made visible or hidden. Layers can be either visible or not. Elements (by type) can also be turned on or off using this icon. 3. Select Visible Entities Using this icon allows the local selection of items regardless of their layer status. 4. Switch Visibility This is where the un-blanked elements are toggled back on, allowing all the elements to be visible again. 5. Flip Visibility We use this icon to flip between the visible and non-visible elements that have been selected using the Blank Entities command. 6. Add/Delete Blank Entities This allows the user to either add or remove elements from the current selection of elements being blanked. 7. Add to Visible Entities Allows you to add entities that are not visible when using the Select Visible Entities option. 8. Remove from Visible Entities Allows you to remove selected visible entities and remove them from a Visible Entities selection. We are concerned with numbers 1 and 2 in this exercise but your instructor will explain the blanking options after the layer management exercise has been completed. Vcamtech Co., Ltd 3

VISI Modelling Layers Select Set Drawing Filters from the toolbar. The screen will now split and the following set of options will appear on the right hand side of the screen. The default is to have 2 layers and is set externally in the visi.cfg file. We can create a series of layers and save them into the visi.cfg file, then, every time the system is opened or a new file is created these layers will be present. We will create more layers here but will not add them to the default visi.cfg file. There are 2 modes of working with layers. An EDIT mode and a VISIBLE MODE The icons below are explained on the following page and some will become active or in-active depending upon which mode we are presently using. See the next page for a description of the above icons Vcamtech Co., Ltd 4

VISI Modelling Layers 1. Visible/Edit Mode This is the icon that toggles the 2 methods on working when in the layer management. The Visible mode is used for selecting the visibility of items on the screen and will dynamically toggle on or off the selected layers. The Edit mode allows the editing of layer names without affecting their visibility. 2. Zoom Mode With this icon turned on, an automatic Fit to Screen will be done every time a layer is made either visible or hidden. With the icon off, the Fit to Screen is not done. 3. Set Current Layer by Element This icon allows the user to select an element from the screen and the current working layer will then be the same as the layer of the selected item from the screen. 4. Set Active Layers by Element This icon allows the user to select an element(s) from the screen and the selected item(s) will then set which layers are visible (Not available in Edit Mode). 5. Set/Reset Layers Use this icon to switch all the items in the layers tree on/off. 6. Invert Selection Inverts your current selection of layers 7. Undo Selection Allows the single last layer selection to be undone. 8. Create or Edit a Group This drop down icon allows a group of layers to be created, edited and/or add or remove layers within the group. 9. Filter by Group This icon allows the user to filter the display of layer names by group. Only layers in the selected group will be seen in the layer list 10. Purge The purge icon is used to delete all redundant layers and groups. Layers will only be deleted if there are no elements present on the layer and it is not the working layer. Groups will only be created if no layers are present in the group. The Green arrow shows which layer is the Current Working Layer The Lock icon shows if the layer is locked or unlocked The Green Tick icon shows that the layer contains geometry. The i icon signifies that the layer has had a comment added. Vcamtech Co., Ltd 5

NOTE! VISI Modelling Layers Once a layer is locked, any of the elements on that layer cannot be edited in any way until the layer is un-locked. A layer comment can be added by double clicking in the last column of the layers panel Double click in this column to add a layer comment. Click the left mouse button in the Layer Name field on layer number 2 and type in Solids. Repeat this on the next layer and enter the following layer names Surfaces Profiles Dimensions At present we have only created the layers and no elements have yet been placed on those layers. Vcamtech Co., Ltd 6

VISI Modelling Layers Select the Create Group icon and enter 3D Data as the name of the group. From the list of layers, highlight the Solids and Surfaces layers. Individual or groups of layers can be highlighted using the standard windows selection methods. (CTRL key, SHIFT key and window selection using the mouse) Select OK Repeat the exercise and create a group called 2D Data, using the following layers LAYER1 Profiles Dimensions Vcamtech Co., Ltd 7

VISI Modelling Layers If we wanted the layers to be saved to the visi.cfg file (which would make those layers and groups available every time we open or create a new file), we would use the Save default icon shown below (this icon is found on the combinations tab which can be seen at the bottom of the layers panel). In this case, we won t save any layers into the cfg Now go back to the Layer Tab and ensure that ONLY LAYER1 is highlighted then close the layer dialogue panel by selecting the X in the corner of the panel Select the Change Attribute icon Use the filters to select all the dimensions only. Select the Select all icon We are now presented with the change attribute dialogue box Vcamtech Co., Ltd 8

VISI Modelling Layers This allows the user to change the properties of the selected items. For this exercise highlight the layer Dimension and select OK We have now placed all the dimensions on a layer called Dimensions and the dimensions will disappear from the screen Repeat the above procedure for the following items: - All Profiles to be on the layer called Profiles All Solids to be on the layer called Solids All Surfaces to be on the layer called Surfaces All the elements have now been placed on their respective layers. Any items that have not been selected will be left on Layer1 We can now switch on or off the items we have placed on different layers. Select the Set Drawing Filter icon The following dialogue box will appear. When all the layers are highlighted, all the layers are visible on the screen. Select only the Dimension layer. You will notice that only the dimensions are now visible on the screen. Individual or groups of layers can be highlighted using the standard windows selection methods. (CTRL key, SHIFT key and window selection using the mouse) The Set-Reset layer icon is a global visible/hidden switch for the layers. Using the tabs at the bottom of this dialogue box we can also be selective of how we view items regardless of whether or not they are placed on a layer and, we can switch them on or off in a GLOBAL manner. Vcamtech Co., Ltd 9

VISI Modelling Layers Try using some of the flags to switch on and off the items on your model, both by layers and element type. By DEFAULT, when we create items they are automatically placed on the Current working layer. We can set the Current working layer in the following manner. Use either mouse button on the layer area of the taskbar as shown below. Vcamtech Co., Ltd 10

VISI Modelling Layers This will bring up the Layers dialogue panel The two buttons at the top of the Layer name and Layer number columns, control the order that the layers are displayed in. The layers can be sorted either numerically or alphabetically in either increasing or decreasing range. Try clicking two or three times on both buttons. Click the Solids layer in the column with the green arrow Click in this column to make that layer the current drawing layer The taskbar will now show the name Solids and is now set as the current working layer. This means that all new geometry created will be on the layer called Solids. Re-set the current working layer back to Layer 1 Create the following layers: - Vcamtech Co., Ltd 11

VISI Modelling Layers Layer Number 50 = Layer Number 100 = Empty layer Temp Now we have layers that are not visible in the current tree it may become necessary to filter out some of the layers. By default there are 256 layers that are user definable. The layers can be filtered out in the following ways: - Select the Combination tab and you will notice that all the Grid Filters are active. The grid filters are used to filter out the layers that will be visible in the Layer tab. Switch on only the following grid filter: - Click here to sort by layer name From the Layer tab all you should see now is the following: - This mean that all we want to see in our layer list are the named layers ordered alphabetically Try the following Grid Filters and see the results: - Vcamtech Co., Ltd 12

VISI Modelling Layers The value here allows the user to set the maximum number of layers they would like to have available. This concludes the Layer Management exercise. Vcamtech Co., Ltd 13

VERO UK TRAINING MATERIAL VISI Workplanes course

VISI Modelling Workplanes Introduction Workplanes are an important part of the VISI-Series software. They are used for the creation of geometry and to align or re-align the model to make working with the model easier for the user. Workplanes are used for both the modeling and machining of components. Imported models are often imported where the origin (workplane) is not at the correct position for future modifications or machining and we need to move the origin (workplane) to one that is more suitable for the job in hand. Workplanes need to be moved and created for machining purposes for both 3-axis, 4-axes and 5-axis positional work. When a new workplane is created and then used for machining, all program origin information is taken from this new workplane. NOTE! All commands related to workplanes are fixed and the UNDO option is not available when the workplane commands have been executed. Vcamtech Co., Ltd 1

VISI Modelling Workplanes Open the File Workplanes.wkf If you notice on this model when we use the command Include All we cannot see the absolute workplane. Create a circle of any size around the absolute workplane. Wireframe > Circle/Arc > Center Radius Now use the command Include All Vcamtech Co., Ltd 2

VISI Modelling Workplanes You will now be able to see the absolute workplane and this is where the model has originally been created. We will now go through the process of creating and moving workplanes The Workplanes toolbar. 1 2 3 4 5 6 7 8 9 10 1. Select Workplane This allows the selection of a saved workplane and displays the set workplane dialogue box. 2. Workplane by 3 points Allows the creation of a workplane via 3 points. The points are usually intersections on the model. 3. Workplane by face This is used to create a workplane by selecting a face. 4. Translate current workplane Creates a new workplane by translating the current workplane to a destination point. 5. Rotate current workplane Creates a new workplane by rotating the current workplane around an axis. 6. Workplane by element A new workplane is created by placing the Z-axis down the selected element. 7. Set workplane to origin This is used to set the active workplane via on-screen selection. Select a previously saved workplane from the screen and that workplane becomes the active workplane. 8. Change workplane Z Creates a new workplane by translating the current workplane a distance in Z. 9. Workplane by current view Creates a new workplane based on the current view. The Z axis of the workplane will point directly towards the user s eye. The workplane origin is at the center of the view. 10. Save current workplane Allows the user to save the current workplane for future use. (If a workplane is not saved, it will be over-written by the next newly created workplane. Vcamtech Co., Ltd 3

VISI Modelling Workplanes There are a few more workplane options (on the System pull-down menu) such as, Delete workplane and Camara to the Workplane, but the most common functions are on the toolbar. Select the Workplane by Face icon Now select the face with the rectangular and circular trimmed holes. Select this surface You will now notice that the workplane has moved from the absolute position to this face. Vcamtech Co., Ltd 4

VISI Modelling Workplanes All new geometry will now be created from this new workplane and not from the absolute workplane unless we specifically define that condition. Select the Workplane by 3 point icon This command works where we have to first select the point of intersection for all 3 axes, then a point for the positive direction of the X-axis and then a point for the positive direction of the Y-axis. Once 2 points are selected then the orientation of the Z-axis is automatically calculated. Select the 2 element intersection icon Now pick the 2 edges of the bottom left hand corner of the trimmed surface with the rectangular trimming. Select these 2 edges This will be the intersection of all 3 axes. Now select the intersection icon Vcamtech Co., Ltd 5

VISI Modelling Workplanes Pick a point along the bottom and side of the trimmed surface with the rectangular trimming. Select point 1 and then point 2 POINT 2 POINT 1 We have now re-created a new workplane using 3 point from the model Now draw a line from one edge of the trimmed surface with the rectangular trimming to the other. We will use this edge to translate our workplane to. Create a line here Vcamtech Co., Ltd 6

VISI Modelling Workplanes Select the Translate current workplane icon Now select the midpoint of the line that we previously created on the model. The workplane will now move to this new point. NOTE! Only a translation point is needed for this command. We do not have to use reference point and translation point. Select the Rotate current workplane icon We are now presented with the following dialogue box Enter the values 70, around the Y- axis Vcamtech Co., Ltd 7

VISI Modelling Workplanes We have now created and modified different workplanes in the most common situations but to use these workplanes to full effect we need to save them as we create them. Select System > Save current workplane Give the workplane a name. This will then save the current workplane and allow us to use and return to this workplane at a later stage if required. Each workplane has 3 default settings that we can use to orient that workplane: - XY Top XZ Front YZ Side These options can be set quickly by clicking with the Left Hand Mouse Button in the workplane option shown in the taskbar at the bottom of the VISI screen. Use this option and see the workplane on the screen rotate to display different orientations. Vcamtech Co., Ltd 8

VISI Modelling Workplanes If we use the Right Hand Mouse Button in this area the select workplane dialogue box will appear The select workplane dialogue box allows the use to select a previously saved workplane and also rotate around the XY Top, XZ Front, YZ Side and also reverse the Z direction of the current or selected workplane. One extra option with regards to workplanes that can be a useful addition to this feature is the command: - Edit > Advanced Transformations > Current Wpl to new Wpl This command will allow the user to translate some of, or the entire model from the current workplane setting to another workplane setting. Select the option Edit > Advanced Transformations > Current Wpl to new Wpl Select all the elements of the model using the Select All icon We now have to select the workplane to translate all the elements to. Select Absolute and then OK All the elements have now been moved onto the absolute workplane. Vcamtech Co., Ltd 9

VERO UK TRAINING MATERIAL VISI Intermediate Component Modelling

INTRODUCTION VISI Modelling Intermediate Pre Requisites It is required that you have successfully completed the Basic Modelling course and the Surface Techniques tutorial. Objectives This training guide will bring together several aspects of VISI modelling including 2D construction, Surface modelling, Solid s modelling and geometry manipulation. The tutorial aims to give an insight into some of the techniques involved in modelling a component in three dimensions from only two dimensional paper drawings. The component to be modelled is shown in the drawing below for reference and will help clarify some of the instructions in the step-by-step tutorial. Vcamtech Co., Ltd 1

VISI Modelling Intermediate STEP 1 Create an 8-sided extruded polygon to form the lower part of the outer casing. 1.1 Create a Polygon Profile from the Profile toolbar. Enter the values for each of the polygon parameters As shown opposite. Select the Centre of Polygon icon from the left hand menu and snap the polygon onto the visible axis as shown below using Intersection Point Note! Click Cancel or press escape to quit from the Polygon input box. 1.2 Extrude the Profile into a 3D solid. Modelling > Extrude elements: Pick the Profile and Select the Z-axis Vcamtech Co., Ltd 2

Enter the extrusion parameters as shown below to create the solid. VISI Modelling Intermediate STEP 2: - Create the domed top of the main exterior shell using a sphere. 2.1 Create a New workplane by moving the current workplane in the Z-axis. System > Change Workplane Z Input the following value Save the Workplane for future use. System > Save Current Workplane Give the workplane a logical name. A green origin plane will appear indicating the Workplane has been saved. Vcamtech Co., Ltd 3

VISI Modelling Intermediate 2.2 Create a Circle on the new Workplane. Use Centre & Radius Circle Using Intersection Point snap to the current Axis Enter the Radius value in the input box. The display should resemble the diagram below. 2.3 Create a 3 Point Arc in the ZX plane to obtain a Radius value for the Sphere. Circle Elem Elem Elem Vcamtech Co., Ltd 4

VISI Modelling Intermediate Make sure ARC Filter is selected from the left hand menu and that Point Co-ordinate input is selected. ARC Filter Point Co-ordinate Using the co-ordinate input box enter the following values for each of the three points when prompted by the software. Point 1 Point 2 Point 3 You should have an arc similar to that shown in the diagram below. Arc shown in XZ plane Vcamtech Co., Ltd 5

VISI Modelling Intermediate 2.4 Create a Sphere from the newly created arc information. Spher Pick the arc Select centre of circle / arc point icon Visi Series has an inbuilt method whereby the value required for a particular operation can be ascertained from other suitable geometry. We will use this method to find the radius value for the sphere. First we need to ensure the sphere radius input box is highlighted: - Double Click or drag select with left hand button to achieve blue highlight. Pick Length of Segment / Arc icon from the left hand menu Then pick on the arc to obtain the radius value. It should appear in the input box as shown below. Vcamtech Co., Ltd 6

VISI Modelling Intermediate You should now have created a sphere of the same radius as the arc, which shares the same centre position. 2.5 Cut the sphere with a plane and remove the lower portion. Cut the sphere with a plane at the current Z zero position. Modelling > Cut Bodies: [Select the sphere solid] Ensure that the Points Environment Icon is selected. Select Z-axis Select point co ordinates and input co-ordinates as shown in the dialogue box. Vcamtech Co., Ltd 7

VISI Modelling Intermediate 2.6 Erase the lower portion of the sphere. Delete Elements Pick the lower part of sphere near an isoparametric line. The result should resemble the picture below. Note! A revolved solid, using Swing An Element could also have been used for this shape, but a primitive sphere creates a greatly simplified geometric surface. Vcamtech Co., Ltd 8

VISI Modelling Intermediate STEP 3: - Connect the 2 solids together with angled walls. 3.1 Use drawing Element filters to temporarily disable the display of solids. Set Drawing Filters Uncheck solid filter The display should show only the 2d elements in the model.(polygon,circle, arc.) Pick the Element /Colour/Style tab 3.2 Split the circle into an arc of 45 degrees. Wireframe > Set of Points > Circular Start / Finish Pick co-ordinate input from the left hand menu to position the centre of the circular set of points. Enter the values as shown below Centre position Point parameters Actual point locations Vcamtech Co., Ltd 9

VISI Modelling Intermediate 3.3 Break the circle with the two newly created points. Pick the two points using the Point s filter Break by points Pick the circle this side Points filter The obtained result Now turn back on the solids with the drawing filters as described in Step 3.1 (Window > View > Set Drawing Filters) 3.4 Create a connecting surface between the solid polygon and the newly created Arc. Create a ruled surface between the two elements. Pick Linear Ruled Surface For the first element selection ensure only the solids filter is selected Pick the top edge of the solid polygon as shown Vcamtech Co., Ltd 10

VISI Modelling Intermediate Pick the 2D Arc using the Arc Filter so that the edge of the solid dome is not selected. The resultant Ruled Surface 3.5 Copy the Ruled surface 7 times to create the remaining surfaces. Edit > Rotation Select the surface to be rotated. Pick Surface Select Insert the point coordinates icon Select the centre of rotation for the copies with the insert point coordinates icon. Enter the values as shown and select the OK button. Vcamtech Co., Ltd 11

Pick Z-axis VISI Modelling Intermediate Select the axis of rotation by choosing the Z-axis Icon. Confirm the selection with a right hand mouse click. Enter the values Shown into the dialog Box as shown. The result of the 7 rotated copies. 3.6 Unite the eight separate surfaces and convert them into a solid. Operation > Unite: [Pick a target surface] 5 6 7 [Pick the remaining 7 surfaces using Multi Select] Ensure Block Control Icon is selected 4 3 2 1 Target You should now have a knitted body comprising of eight ruled surfaces. This body is not a closed volume because it still has an open base and top face. The body must be converted into a solid. Because the open ends are planar, this can easily be done. Vcamtech Co., Ltd 12

VISI Modelling Intermediate Operation > Close to Solid: [Pick the knitted ruled surfaces] You can use the?(menu) > Status function to confirm you have three solids. 3 2 We now have 3 separate solid bodies 1 3.7 Use the same Unite command to join the 3 separate solid bodies together. Operation > Unite: [Pick a target solid] 3 2 Target Solid Use the Select All Filter to unite the remaining 2 solid bodies. You should now have successfully created a single solid body. STEP 4 : Add Blends onto sharp external edges. You can check if you have a single solid using the? > Status drop down menu Operation > Blends: Choose Single Edge Mode with Block Control Apply Blends to the following 8 edges. Single Edge Block Pick these edges consecutively and the 7 remaining pairs of edges. Vcamtech Co., Ltd 13

VISI Modelling Intermediate Insert the Blend radius value. The result of the Blending Functions 4.1 Create a Blend around the top edge loop of the component. Operation > Blends: Choose icon Select Edges of Face by Loop It is required to pick 2 edges of a face to activate a loop selection. Pick this edge first Insert the Blend Value Pick this edge second Vcamtech Co., Ltd 14

VISI Modelling Intermediate 4.2 Create a Blend around the lower remaining sharp edge. Operation > Blends: Choose icon Single Edge Single Edge Pick this edge Final result of all edge blending operations When inserting the radius value, make sure Propagate over tangent edges is selected. This will allow the blend to loop all the way around the edges. STEP 5: Give the component a wall thickness. Operation > Offset/Hollow Bodies: [Pick the Solid] Select the Hollow method and input the following wall section value and parameters as displayed opposite. Now select the icon near the top of the Hollow Bodies panel which allows you to Select faces with none default offset. Vcamtech Co., Ltd 15

VISI Modelling Intermediate Dynamically rotate the model and select the bottom face, and then activate the pierced option in the panel that appears. Now click M2 twice to get back to the Offest/Hollow Bodies main panel then click preview and/or OK to perform the operation. The result of the hollow operation should look like this. STEP 6: Add a shoulder step into the sidewalls of the model Create an Offset Profile from the original 8-sided polygon profile. Select Profile Offset Pick the original Profile. Vcamtech Co., Ltd 16

VISI Modelling Intermediate Set the offset distance as shown below: - Inner Profile created Note! By selecting the preview button within the Profile Offset dialog box you will see if the offset profile is offset on the correct side of the original profile. If you need to change the offset direction simply select the Reverse Direction tick box. 6.1 Create the shoulder as a solid feature. Operation > Pocket from profile: [Pick the solid model] [Pick the inner profile] Input the height of the shoulder and the taper angle. The result of the Pocket from Profile Operation STEP 7: Create Inner Ring Feature Firstly, activate the original Absolute Workplane by picking the Active workplane box in the bottom right hand portion of the screen. Use RH mouse button. Active Workplane Vcamtech Co., Ltd 17

VISI Modelling Intermediate Select Absolute from the available list making sure XY Top is checked Now that the Absolute Workplane is activated create an 8-sided Polygon Profile Polygon Profile Enter the values shown opposite making sure the Circumscribed button is checked. Place the polygon at the following position. Pick Centre of Polygon Pick Point Co-ordinate input Insert these co-ordinates. Make sure the workplane button is checked. Vcamtech Co., Ltd 18

7.1 Offset the Profile to create an inner profile VISI Modelling Intermediate Pick the profile making sure that the new offset profile is created on the inside of the original Offset Profile Input the offset distance. Ensure the Reverse direction tick box is selected. The obtained result. 7.2 Extrude the outer profile to create a solid polygon shape. Modelling > Extrude elements: [Pick the outer Polygon Profile] Pick Outer Profile Enter the extrusion values Select Z axis The extruded solid should appear through the top of the main body shell Vcamtech Co., Ltd 19

VISI Modelling Intermediate 7.3 Hollow the new extrusion to create the ring. Operation > Pocket from profile: [Pick the solid extrusion] 1) Pick the solid extrusion Enter pocket parameters Expected Result 2) Pick inner Profile 7.4 Trim the extruded ring back to the main shell body. Operation > Cavity: 1) Pick the ring as the target body [Pick the extruded ring] [Pick the Shell Body] Input Zero Cavity Offset 2) Pick the shell as the cavity body The extruded ring will have been separated into 2 pieces. Remove the upper portion. Erase top section Pick Erase Vcamtech Co., Ltd 20

7.5 Unite the ring and the shell body together to create one single solid. Operation > Unite: [Pick Shell Solid] [Pick Ring Solid] VISI Modelling Intermediate Shell Solid Ring Solid 7.6 Clean the model up by removing existing 2D elements. Pick Erase Turn Off the Solids Filter Pick Select All Elements STEP 8: - Creation of Clip Features Setting up a new construction Workplane. System > Rotate Current WKP Rotate the current Workplane around the Z-axis at the specified value. Vcamtech Co., Ltd 21

VISI Modelling Intermediate Switch the Workplane to the Current YZ Side and change the viewing mode to REL(ative) to the current work plane. Left click twice to interactively activate the Current YZ Side Workplane Left click once to switch the view mode to RELative System > Save Current Workplane Save the new plane with a new name Make sure the new Workplane is activated and the view is relative. Clip-plane XY Top should be active and View Relative switched on Expected Orientation Of Plane Set the View to look directly onto the new workplane Press F2 to set the view to Top Expected View Vcamtech Co., Ltd 22

VISI Modelling Intermediate STEP 9: - At this stage you can choose to construct the 2D Clip Feature from scratch using the drawing on the second page or use the previously created 2D symbol. This tutorial will explain how to use the symbol you created earlier. Load the symbol into the workspace and position it correctly. Annotation > Symbol > Load a Local Symbol [Open Clip2d.sym] The symbol will be attached to the cursor at this position. NOTE! The clip symbol was drawn twice-full size. You will need to scale it by 0.5 when you load it in. Use this icon Position the symbol using Point co-ordinate input. Use the Point Co-ordinate input method. Enter the following values making sure Work plane button is checked. You will notice the 2D clip is slightly longer than the outer shell. This is so the clip will correctly intersect the shell as a solid form. Vcamtech Co., Ltd 23

VISI Modelling Intermediate 9.1: A symbol cannot be extruded directly. First, you need to dissolve it into segments, then chain it into a closed profile Edit > Dissolve Aggregates [Pick the 2D Clip Symbol] (The symbol is converted into segments) 9.2: - Now create a closed profile from the segments ready for solid extrusion. Pick Closed Profile Select the first element for the profile Click Delete Original Geometry to replace original elements with the Profile Click Automatic Profile to automatically chain the elements. Confirm to create the Profile 9.3: - Extrude the profile into a solid object. Modelling > Extrude elements: [Pick the Clip Profile] Make sure Z axis is selected Extrude the profile in both directions The result of extruding the clip in both directions should look like this. Vcamtech Co., Ltd 24

VISI Modelling Intermediate 9.4 Add draft angles onto the faces of the solid clip. It is probably easier to add the draft onto the clip if the main body is hidden. Use the Blank Entities function (on the Attributes/Filters toolbar) to hide everything except the clip. Ask the tutor if you are unsure about how Blank Entities works. Modelling > Incline a face Use the select faces directly option. You will need to rotate the view around so you can pick all four faces. Use Block Control to pick multiple faces Pick these 4 faces of the clip Pick an application point for the faces to rotate about. Any of the four bottom corners will produce the desired result. Select the Axis direction to apply the draft. Select the Y-axis icon Add a negative draft angle Vcamtech Co., Ltd 25

VISI Modelling Intermediate The effect of adding draft to the clip should look like this. Now use the Blank Entities function to display the rest of the model again. 9.5 Adding a Blend to the back edge of the clip Operation > Blends Pick Single Edge Blends Pick this edge Add the Blend Value Blend Applied Vcamtech Co., Ltd 26

VISI Modelling Intermediate 9.6 Trim the clip back to the inside of the main body. Operation > Cavity: [Select the Solid Clip] [Select the Shell Body] 1) Pick Clip as Target object Pick the main model as the cavity body Leave the cavity offset at zero 9.7 Delete the unwanted portion of the clip Pick Delete Elements Remove the upper part of the clip Vcamtech Co., Ltd 27

VISI Modelling Intermediate 9.8 Copy and rotate the Clip to three new positions Edit > Rotation Pick the clip to be rotated Select the rotation centre point by inserting the point coordinates and enter the values shown below. Pick Y-Rotation Axis The result of the rotation with copy command. Vcamtech Co., Ltd 28

VISI Modelling Intermediate 9.9 Unite the 4 clips to the main body. Operation > Unite [Pick the main body solid] [Pick the 4 rib features] Using select all icon 1) Pick main body solid as target body. Pick the ribs X 4 To do this quickly use the Select All icon Select All 10.0 Scale the part to allow for moulding shrinkage. Say 0.5% for ABS Edit > Scaling [Pick the Solid Component] Pick Point coordinate Input to specify the scaling position Use Work plane origin for scaling centre Vcamtech Co., Ltd 29

VISI Modelling Intermediate Add the Shrinkage value to complete the model. Hint. Use the? > Status function to check if everything is OK. You should only have one solid. If you have two solids, ask the tutor to explain where you went wrong. Congratulations you have just completed the Intermediate Modelling tutorial. Your model should look like the one below if you have successfully followed all the stages. Vcamtech Co., Ltd 30

VERO UK TRAINING MATERIAL Version 16 VISI Surface Techniques

VISI Modelling Surface INTRODUCTION Pre-requisite It is important that before you attempt the 3D surface training examples you must have completed and fully understood the previous VISI-Design and VISI-Modelling examples. The following example contains a VISI workfile broken into 15 sectors, each containing the geometry required for a specific surfacing function. Within this example we will look at all surfacing techniques. From the menu select File> Open Select the file Surface Explanation.wkf and select open Vcamtech Co., Ltd 1

SOLID > PLANE FROM A CLOSED AREA VISI Modelling Surface This is a convenient method for generating a plane as a sheet body (solid with zero thickness) by picking the area within a closed perimeter of elements. Position the cursor anywhere within the closed area, the system automatically finds the closest perimeter and converts the area to a sheet solid surface. Using the Point mode environment, select a free hand point inside the closed boundary Point Environment Set Grid Parameters Sliding Insert the Point Coordinates Intersection Point Parametric Point on a Segment/Arc Quadrant of a Circle Enhanced Picking Enable / Disable Element Filter Project onto Current Workplane Select a Point with the Mouse Nearest Point in Polar Co-Ordinates Two Element Intersection Centre of a Circle / Arc Point Filter Equidistant Point Set / Cancel Filters NOTE! For this function to work, all closed geometry must lie on the current workplane. Vcamtech Co., Ltd 2

VISI Modelling Surface SOLID > PLANE BY THREE POINTS This command creates a planar sheet body by giving three points. The first and second points define the horizontal length of the plane and the third point defines the vertical length. Using the Point mode environment, select the 3 points within area 2 Set Grid Parameters Sliding Insert Point Coordinates Intersection Point Parametric Point on a Segment /Arc Quadrant of a Circle Enhanced Pick Enable/Disable Element Filter Project onto Current Workplane Mouse Point Nearest Point in Polar Coordinates Two Element Intersection Centre of Circle/Arc Point Filter Equidistant Point Set / Cancel Filters [P2] [P3] [P1] Vcamtech Co., Ltd 3

VISI Modelling Surface SOLID > RULED SURFACE > LINEAR RULED Creates a surface in space between two pre-defined curves, segments, arcs or profiles, by uniting all the points of each of the curves. The surface is created by linear interpolation between the same parameter positions along each of the two shape curves. Select the first shape curve - Select shape 1 Select the second shape curve - Select shape 2 Shape 1 Shape 2 SOLID > RULED SURFACE > CIRCULAR RULED FROM 2 EDGES This function creates a surface whose cross sections form a circular section. Pick the two drive curves that represent the edges of the surface, and then specify the start and end radii. The proposed radii are the minimum radii allowed. Select the first shape curve - Select shape 1 Select the second shape curve - Select shape 2 Use the SPACE BAR to determine on which side the surface will be created Confirm using the right hand mouse button - <M2> Shape 2 Shape 1 Vcamtech Co., Ltd 4

VISI Modelling Surface SOLID > RULED SURFACE > CIRCULAR RULED FROM 3 EDGES This function creates a surface whose cross sections form a circular section. Pick the three drive curves through which each section must pass. Select the first shape curve - Select shape 1 Select the second shape curve - Select shape 2 Select the third shape curve - Select shape 3 Shape 3 Shape 1 Shape 2 SOLID > OTHER SURFACES > LOFTED SURFACE Generates a surface by linking together a series of sectional curves. Select the individual sectional elements on the same side. The sectional curves can be selected manually (one by one), or using a multiple selection (by picking the first and the last curve). NOTE! The orientation of the shape curves is not important for the creation of the surface. As the curves will be oriented depending on the end selected, all the curves should be selected towards the same end. Select an element - Select shape 1 Select an element - Select shape 2 Select an element - Select shape 3 Select an element - Select shape 4 Confirm using the right hand mouse button. <M2> Vcamtech Co., Ltd 5

VISI Modelling Surface Shape 3 Shape 4 Shape 2 Shape 1 SOLID > OTHER SUFACES > LOFTING IN 2 DIRECTIONS This function will produce a surface from a series of "horizontal" and "vertical" sectional curves. The use of the horizontal and vertical curves requires that these curves intersect. Select the horizontal curves, then confirm with right hand mouse button before selecting the vertical curves. NOTE! The orientation of the shape curves are not important for the creation of the surface. As the curves will be oriented depending on the end selected, all the curves should be selected towards the same end. <M2> button <M2> Select an element ( U Direction ) - Select shape 1 Select an element ( U Direction ) - Select shape 2 Confirm using the right hand mouse button Select an element ( V Direction ) - Select shape 3 Select an element ( V Direction ) - Select shape 4 Select an element ( V Direction ) - Select shape 5 Select an element ( V Direction ) - Select shape 6 Confirm using the right hand mouse Shape 6 Shape 2 Shape 5 Shape 4 Shape 3 Shape 1 Vcamtech Co., Ltd 6

SOLID > OTHER SURFACES > LOFTING IN 2 DIRECTIONS VISI Modelling Surface This function is another adaptation of the lofting in 2 directions function but will allow you to produce a periodic lofted surface. The selection of the curves in this function is extremely important as the result can differ depending on the curves that are selected. Firstly deselect the multiple selection icon Multiple Selection Icon Select an element ( U Direction ) - Select shape 1 Green Curve (S1) Select an element ( U Direction ) - Select shape 2 - Orange Curve (S2) Select an element ( U Direction ) - Select shape 3 - Brown Curve (S3) Select an element ( U Direction ) - Select shape 4 - Pink Curve (S4) Select an element ( U Direction ) - Select shape 5 Green Curve as we want a seamless surface (S5) Confirm using the right hand mouse button <M2> Select an element ( V Direction ) - Select shape 1 Blue Curve (D1) Confirm using the right hand mouse button <M2> S4 S3 S1 + S5 D1 S2 SOLID >OTHER SURFACES > ADVANCED LOFTED SURFACE This command is very similar to the command Lofted surface apart from it is possible to define the tangency speeds and constraints. Using this command it is possible to create a surface that is tangent to the start and end edges that are picked but also passing the N number of curves. It also allows the option of changing the tangency values on the fly. With this ability it give more flexibility in the surface that is created. Vcamtech Co., Ltd 7

VISI Modelling Surface - Select the first edge of the surface E1 (The middle elements are going to be the two curves in the middle of the start and end surfaces) - Select the two curves C1, C2 and confirm with the right hand mouse button (The end edge must be a surface.) - Select the last edge E2 E2 C1 C2 E1 By changing the tangency values it is possible to speed up and slow down the tangency change between the start and end surface. Please ask your Instruction for an example. Select OK to the dialog box. The result: Vcamtech Co., Ltd 8

VISI Modelling Surface SOLID > OTHER SURFACE > ADVANCED LOFTING IN 2 DIRECTIONS (N SIDED PATCH) With this command it is possible to have a number of surface edges that lie in the U and V direction. Ordinarily when trying to create a patch surface in this type of situation we would need to draw the edges of the surfaces, concatenate them together in order to create the four sides required to use the Patch surface function. With the introduction of the new Advanced lofting in 2 directions we can now simply pick multiple surface edges directly in order to create one side of the patch surface Note! The number of edges that make up the start edge in the U direction must equal the same number of edges that make up the middle or end side also. This also applies for the V direction. This side consists of 6 edges; therefore the opposite side must also equal six for the command to work Ensure the select single edge selection icon is active and also the block control icon as we need to pick more then more then one edge to define a side of the patch surface. Vcamtech Co., Ltd 9

VISI Modelling Surface - Select the first edge of the first side E1 - Select the second edge of the first side E2 - Select the third edge of the first side E3 - Select the fourth edge of the first side E4 - Select the fifth edge of the first side E5 - Select the sixth edge of the first side E6 E6 E5 E4 E3 E2 E1 Confirm the first set of edges in the U direction with M2 At this point it is possible to select middle reference elements to control the geometry of the surface, in this example we have no middle reference elements. Simply select M2 to skip the middle reference element selection. We now need to repeat the same process for the opposite side (middle elements) - Select the first edge of the second side E7 - Select the second edge of the second side E8 - Select the third edge of the second t side E9 - Select the fourth edge of the second side E10 - Select the fifth edge of the second side E11 - Select the sixth edge of the second side E12 Confirm the second set of edges in the U direction with M2 Vcamtech Co., Ltd 10

VISI Modelling Surface With the edges in the U direction now defined we can now repeat the process for the V direction Following the same rules that are used in the conventional patch surface command select the edges where indicated using the block control - Select the first edge of the third side V1 - Select the second edge of the third side V2 - Select the third edge of the third side V3 V1 V2 V3 Confirm the first set of edges in the V direction with M2 - Select the first edge of the forth side V4 - Select the second edge of the forth side V5 - Select the third edge of the forth side V6. Confirm the second set of edges in the V direction with M2 Inside of the dialog box that appears it is possible to change the tangency result by un-checking and checking options inside of the Lofting Body dialog box. Select OK to the dialog box that appears. Vcamtech Co., Ltd 11

VISI Modelling Surface The Result: SOLID > OTHER SURFACES > ADVANCED LOFTING IN TWO DIRECTIONS (TANGENCY ) With this command it is possible to produce a tangent surface while passing through N number of curves in the U and V direction. Select the start reference edge (Select the edge marked E1) Select the middle reference curves (Select C1 C6 and confirm with M2) Finally for the U direction select the end reference edge (Select the edge marked E2) E2 E1 C1 C2 C3 C4 C5 C6 Vcamtech Co., Ltd 12

VISI Modelling Surface To specify the reference edges for the V direction select the edge V1 followed by V2. Confirm the start and end curves with M2. V1 NOTE! Skip past the selection for a middle element by simply Right hand clicking V2 Once again it is possible to get varied results by changing the tangency options opposite. Select Ok to the dialog box. Vcamtech Co., Ltd 13

SOLID > SURFACE BY 1 DRIVE 2 SHAPE CURVES VISI Modelling Surface Creates a surface as the evolution of a primary shape curve towards a second shape curve along a directional or driving curve. The drive curve defines the surface shape in the longitudinal direction (the U direction of the surface), and the shape curve defines the sectional shape (the V direction). It is possible to define two different shape curves that define the surface cross sections at each end of the drive curve, but the same command will also drive a single shape curve along the directional curve. NOTE! If there are two different shape curves, then their direction and application points are relevant. If the surface created self intersects, it will be necessary to reverse one of the curves, and / or pick a different application point. Select the drive curve - Select shape 1 Select the first shape curve - Select shape 2 Select the application point - Select Point 1 [P1] Select the second shape curve - Select shape 3 Select the application point - Select Point 2 [P2] [P2] Shape 3 Shape 1 Shape 2 [P1] The resulting surface can be influenced by changing the settings within the displayed dialog box. NOTE! Ensure the Automatic tick box is selected to preview the effect of changes within the dialog box. Vcamtech Co., Ltd 14

VISI Modelling Surface SOLID > OTHER SURFACES > SURFACE BY 2 DRIVE 2 SHAPE CURVES Creates a surface as the evolution of a primary shape curve towards a second shape curve along two driving curves. If you tag the option Maintain constant height, the system interpolates any change in height between the curves in proportion to the distance along the drive curve. This normally leads to a constant change in height or constant height between one shape curve and other. If you do not tag this option the system generates a height for the surface which is proportional to the distance between the directional drive curves (width). Select the first drive curve - Select shape 1 Select the second drive curve - Select shape 2 Select the first shape curve - Select shape 3 Select the second shape curve - Select shape 4 Shape 2 Shape 1 Shape 3 Shape 4 SOLID >OTHER SURFACES > PATCH SURFACE Creates a patch surface between three or four boundary curves. The curves must join at the corners of the patch. NOTE! The selection is the same as that of four-sided patch, but instead to select the fourth edge you must confirm with the right hand mouse button. In general a patch should not be used as an alternative to a blend or generated surface as it has fewer controls for tangency or parallelism with other elements surrounding it. Vcamtech Co., Ltd 15

VISI Modelling Surface 3 SIDED PATCH button Select the first curve - Select shape 1 Select the second curve - Select shape 2 Select the third curve - Select shape 3 Confirm using the right hand mouse Shape 2 Shape 1 Shape 3 4 SIDED PATCH Select the first curve - Select shape 1 Select the second curve - Select shape 2 Select the third curve - Select shape 3 Select the fourth curve - Select shape 4 Shape 4 Shape 1 Shape 3 Shape 2 Vcamtech Co., Ltd 16

VISI Modelling Surface SOLID > DRAFT SURFACES > DRAFT SURFACE FROM a CURVE Creates a surface by applying a constant or variable draft angle to a selected element. The elements are extruded to heights defined from the selected elements, the workplane or absolute height value. Select the curve - Select shape 1 Shape 1 SOLID > PIPED SURFACE Creates a piped surface (tube) from a selected reference element (segment, circle, arc, curve or profile). Start Radius - Radius of the start of the pipe. End Radius - Radius at the end of the pipe. Vcamtech Co., Ltd 17

VISI Modelling Surface NOTE! A pipe with a different start and end size cannot be applied on curves with sharp corners. The position on the reference element that you identify is significant, the system considers the start point for the surface to be the nearest extremity of the element. If the selected reference element is a closed element (e.g. Circles) the system requests only a single Radius value, as the start and the end points of the reference element are coincident and the pipe is made continuously. Zoom into area 10. Surface tangent to 2 faces / surfaces SOLID > SURFACE TANGENT TO 2 FACES / SURFACES This command will produce a surface tangent to two series of faces. NOTE! The tangent surface will be generated from the two edges closest to the selection point. It is important that the selected faces must be picked at similar positions. Select Edge 1 - Select side 1 Select Edge 2 - Select side 2 Vcamtech Co., Ltd 18

VISI Modelling Surface Side 1 Side 2 SOLID > TRIM SURFACE > CREATE TRIMMED SURFACE This command creates a trim or trimmed boundary for an existing surface. The trim boundaries can be defined by profiles, sequence of elements (group), segments and or curves. Pick the surface to be trimmed within the part to be retained, then select the trimming elements. The dialogue box defines the trimming elements projection method. The elements can be positioned in space and can be projected on the surface to trim the extent of the surface. Select the surface to be trimmed - Select surface at Point 1 [P1] Select the trimming curves - Select all curves on surface [P1] Trimming curve Surface selected outside trimming curve will leave this result Surface selected inside trimming curve will leave this result Vcamtech Co., Ltd 19

VISI Modelling Surface SOLID > EDIT TRIMMING This function removes, reverses, or duplicates the trimming on trimmed surfaces. Removal closes an interior hole, and deletes the external loop. The body will revert to an untrimmed state. Reversal deletes the original body, and creates new bodies from the interior portion of holes, and from those areas that lie outside the exterior trimming loop. Duplication retains the original body, and also creates new bodies in a similar manner to the reversal option. SOLID > EXTRACT FACE AS SURFACE Allows you to extract one or more faces of a reference solid transforming them into surfaces. You can decide to retain or to remove any existing trimming of the selected faces. Using the Dialog box it is possible to control the trimming condition and the location of the extracted faces. Using the Extract Face as Surface command select Face1 and select the preview button from the dialog box. You will notice that a sheet body has been created on top of the solid. If you now select the Incremental option from the dialog box and enter values into any of the XYZ boxes you will see the extracted face move the entered distance from the original solid. Vcamtech Co., Ltd 20

VISI Modelling Surface SOLID > JOIN / CONCATENATE / FORCE TANGENCY This command allows you to edit two series of faces. Different results can be obtained depending on the surface switch setting selected within the dialog box. Vcamtech Co., Ltd 21

VISI Modelling Surface NOTE! The surface will be modified from the two edges closest to the selection point. It is important that the selected faces must be picked at similar positions. Select face 1 - Select side 1 Select face 2 - Select side 2 Side 1 Side 2 SOLID > EDIT SURFACES > EDIT VERTICES This function allows you to modify the vertices that compose the surface. Existing vertices can be translated, rotated, projected or scaled. Vertex rows or columns may be deleted or added. The surface may be a single sheet body, or it may be the face of an existing body. In the former case the original body will be replaced with the modified surface, and in the latter case a new sheet body will be created. When the surface has been selected the existing vertex net will be displayed. Each vertex will be shown as a rectangle, and a continuous line will connect rows of vertices in the U direction. A dashed line will connect those in the V direction. Select the surface to modify - Select surface 1 Select the vertices to modify Z+100 - Select the highest vertex and move it Surface 1 Vcamtech Co., Ltd 22

VISI Modelling Surface OPERATION > MULTIPLE BLEND ON SURFACES / FACES This command is an operation that takes two (disjoint) sets of faces and produces blends between them. It differs from edge blending in that: The face sets need not be adjacent, or even in the same body. The command will work with solid and surface bodies, and can be used to combine bodies. The blend may either have a constant or variable radius, and the cross sectional shape may either be defined as a rolling ball or as a disc. Rolling Ball Blend. A rolling ball blend has a cross section that lies in the plane normal to the two underlying surfaces. Disc Blend A disc blend has a cross section that lies in a plane orthogonal to the parameter spine. Parameter Spine A parameter spine is a curve that is used to define the radii for variable radius and disc blends. For disc blends it also defines the plane of the blend cross section. Tangent Edge Blends For tangent edge blends actual edges on the solid must be selected. Wire frame curves cannot be used. If the edges do no exist, then the function Project Curve onto Body has an option Create Edges. Any redundant edges may be deleted by simplifying the body. Select the first face - Select face 1 NOTE! Select the second face - Select face 2 When blending surfaces the surface side is important. Different results can be obtained. Surface 1 Surface 2 Vcamtech Co., Ltd 23

SOLID > AUTO CONSTRAINED SURFACE VISI Modelling Surface The auto constrained surface option will systematically step through all of the available surface creation possibilities. The system initially re-orders the curves and internally steps through all available creation methods depending on the curve type selected. for example (i) lofting, if that fails the system uses (ii) adv lofting etc. There are three options for selecting geometry within the command:- Wire frame Selection. Surface Edge Selection. Combination of both Wire frame & Surface Edge Selection. WIRE FRAME SELECTION Using the auto constrained surface simply create a selection window around the first example inside the area 21. Selection Window To confirm the element selection simply press the M2 mouse button. Select the preview button to see a preview of the resulting surface before pressing OK to accept the created surface. Vcamtech Co., Ltd 24

VISI Modelling Surface Using the same window selection method continue to create surfaces from all the groups of curves in this section. Complete the exercise by filling in the missing surfaces from the sheet body. SURFACE EDGE SELECTION It is possible to use the Auto Constrained Surface when there are no curves available by selecting the edges of surfaces. Using this method it is possible to control the tangency condition of the surface being generated. Select the Auto Constrained Surface option, then press the M2 mouse button to change to reference edge selection. Curve selection options M2 Mouse Click Reference Edge selection Vcamtech Co., Ltd 25

Select the two reference edges of the surfaces P1 & P2 as shown below. VISI Modelling Surface P1 P2 Select the preview button to display the resulting surface. Within the dialog box it is possible to remove the tangency conditions so a ruled surface is created. Follow the same process to generate a surface between the three edges of the sheet body. Vcamtech Co., Ltd 26

VISI Modelling Surface WIRE FRAME & SURFACE EDGE SELECTION Using this final example it is possible to create a surface using a combination of both curves and reference edges of existing surfaces. Using the techniques that you implemented in the two previous examples repair the surface model by selecting the guide curves with a window selection and the confirming the operation with the M2 mouse key and then selecting the two reference edges to create the surface. If you have any trouble ask your tutor for assistance. Vcamtech Co., Ltd 27