Diagnostic tester Instruction Manual Software ENGLISH Prepared by: Approved by: Sylwester Czupryna Sebastian Żur ElproSys Sp. z o.o. ul. Tarnogórska 140 44-102 Gliwice 1
1 LEGAL RESERVATIONS AND AGREEMENT OF USE 3 2 MENU NAVIGATION ( MULTI-TOUCH SCREEN) 4 3 MAIN SCREEN 5 4 KEYPAD 6 5 MENU ICONS DESCRIPTION 6 6 SETUP 7 7 SUBMENU INFORMATION 8 8 SUBMENU TESTS 8 9 TOOLS 9 10 MENU SUBJECT OF PROGRAMMING 10 11 EXEMPLARY PROGRAMMING 11 12 BASIC SETTINGS 12 13 DIAGPROG4 MANUAL UPDATE 14 14 MAINTENANCE 14 15 DISPLAY FIRMWARE UPDATE 15 16 RESTART DIAGPROG4 15 17 DIAGPROG4 MANAGER 16 18 DESCRIPTIVE MENU 17 2
1 LEGAL RESERVATIONS AND AGREEMENT OF USE Once Diagprog4 device is switched on user should select language from the supported languages list. Language selection will result in the change of language in the entire menu. User should review LEGAL RESERVATIONS and AGREEMENT OF USE. By selecting the Agree accept button user accepts AGREEMENT OF USE and Diagprog4 device will switch on. It is necessary to accept AGREEMENT OF USE each time device is switched on. 3
2 MENU NAVIGATION ( MULTI-TOUCH SCREEN) Simple gestures tapping or pressing with fingers is enough to select menu options. In order to navigate the menu using keypad press Accept button keypad. to activate it and fully use - Accept, - Cancel, - Top, - Bottom 4
3 MAIN SCREEN To navigate the main screen please use main screen icons or top/bottom buttons on the keypad. MAIN SCREEN ICONS ICONS FUNCTION Cars Motorbikes Other Tools Setup Information Special programs VIN programs Accept Icon Cancel Icon Top Icon Bottom Icon Selection of a car model Selection of a motorbike model Selection of a quad, scooter, tractor model Basic Tools Basic Setup Information about Diagprog4 Runs special/diagnostic functions Read car s VIN numer. Car selection based on VIN number. Allows to accept Allows to cancel Allows to MOVE UPWARDS in the menu Allows to MOVE DOWNWARDS in the menu 5
4 KEYPAD Keypad below the multi-touch screen is another way to navigate DiagProg4 menu. KEYPAD - BUTTONS BUTTONS FUNCTION Accept Button Cancel Button Top Button Button to ACCEPT Button to CANCEL Button to MOVE UPWARDS in the menu Bottom Button 5 MENU ICONS DESCRIPTION Button to MOVE DOWNWARDS in the menu Example of MENU DIAGNOSTICS SERVICES ADVANCED EDITING ODOMETER/ HOURMETER PROGRAMMING IMMOBILIZER EEPROM READ/WRITE FLASH READ/WRITE ADVANCED DIAGNOSTIC FUNCTIONS FUNCTIONS FOR ADVANCED USERS CLEAR CRASH DATA MENU ICONS - description DIAGNOSTICS SERVICES ADVANCED EDITING ODOMETER/ HOURMETER PROGRAMMING IMMOBILIZER CLEAR CRASH DATA EEPROM READ/WRITE FLASH READ/WRITE ADVANCED DIAGNOSTIC FUNCTIONS FUNCTIONS FOR ADVANCED USERS Automotive diagnostics Service inspection - reading, writing, editing ODOMETER/ HOURMETER programming immobilizer Clearing accident data Reading and writing EEPROM content Reading and writing FLASH content Advanced diagnostic functions Functions for advanced users 6
6 SETUP SETUP MENU FEATURES ICON ACTIVE TECHNICAL SUPPORT DEFAULT SETTINGS DOWNLOAD UPDATE/ ACTIVATION INFORMATION LANGUAGE MAINTENANCE OBDII/VOLTAGE TEST SETTINGS OTHER SETTINGS POWER SAVING SECURITY TESTS WIFI SETTINGS DESCRIPTION Provides access to all data sent automatically to seek active technical support Restoring the device to the original state once initially used Allows user to check for new updates/ activations Information about DiagProg4 Menu language selection: Polish, English, German, French, Italian, Spanish, Portuguese, Brazilian File synchronisation between device and files on the server Power supply to connected module and OBDII connector Settings modification: e.g. contrast, volume Switch ON/OFF screensaver DiagProg4 additional security measures Tests available for the user WIFI settings modification 7
7 SUBMENU INFORMATION ABOUT DIAGPROG4 CONTROL NUMBER DATE/TIME DEVICE LIMITS AGREEMENT OF USE IMPORT DP3 LICENSES OPEN-SOURCE LICENSE Information about DiagProg4 Used for registration in customer zone at www.diagprog4.com Information about date and time Information about DiagProg4 limits Information about DiagProg4 Agreement of Use Allows to transfer all active programs from Diagprog3 to Diagprog4 Information about Open-Source license DiagProg4 8 SUBMENU TESTS EXTERNAL INTERFACE TEST CHECK SDHC CARD FAT32 SYSTEM MULTIPLEX TEST External interface test Micro SDHC card compatibility with FAT32 system test MULTIPLEX test 8
9 TOOLS ICON CAN ANALYZER (Internal use only) CAN PLAYER (Internal use only) CAN TERMINATION CONTROL DOWNLOAD UPDATE/ ACTIVATION EEPROM PROGRAMMER EXTERNAL UNIT POWER HEXEDITOR J1850 ANALYZER (Internal use only) K-L ANALYZER (Internal use only) MICROCONTROLLER PROGRAMMER RESTART DIAGPROG4 RESTORE THE BACKUP MODULE SENDING LOG FILE SUPPORT SCRIPT UDS COMMUNICATION CONTROL UNIT CALCULATOR DESCRIPTION Programs For Internal Use Only Programs For Internal Use Only Enables/ disables High Speed CAN Termination Allows user to check for new updates/ activations Write EEPROM memory Power supply to connected module File editing in hexadecimal system Programs For Internal Use Only Programs For Internal Use Only Write FLASH + EEPROM Immediate restart in order to reload operating system Restore backup file saved on SD card Send *.LOG file to ElproSys server for technical support Runs support script prepared for user by technical support team Enables/ disables UDS communication Enables metric conversion 9
10 MENU SUBJECT OF PROGRAMMING Menu Subject of programming can be Menu for CARS, MOTORBIKES and OTHER VEHICLES. EXEMPLARY PROGRAMMING MENU 10
11 EXEMPLARY PROGRAMMING Exemplary programming of Alfa Romeo \ 146/146 \ ST5249 MENU FOR BRAND SELECTION MENU FOR MODEL SELECTION MENU FOR MODULE SELECTION MENU FOR THE TYPE OF PROGRAMMING SELECTION PROGRAMMING MENU 11
12 BASIC SETTINGS WIFI settings Select SETUP, next select WIFI settings from the menu and connect to WIFI network. Select available WIFI network and enter password. If WIFI network connection is correct then information about network will be displayed next time WIFI SETTINGS are selected until the device is disconnected from the network. Information about WIFI enabled by default is stored on SD card. Without SD card device will not remember WiFi network. LANGUAGE settings Select SETUP, next select LANGUAGE from the menu and accept with OK button. 12
SENDING LOG FILE If any error occurs during module programming DiagProg4 sends LOG file to ElproSys server for Technical Support. SENDING LOG FILE MANUALLY Select TOOLS, next select SENDING LOG FILE from the menu. Sending LOG file is only possible when device is within WIFI network range. If LOG file is sent successfully message will be displayed on the screen. LOG file can be sent using dedicated software - DiagProg4 Manager. 13
13 DIAGPROG4 MANUAL UPDATE Connect DiagProg4 to PC via mini USB cable (Linux, Unix, MAC OS, Android or Windows), it will appear as an additional external drive. Save update.dpu file, received directly from ElproSys or its representative in the main folder of microsdhc card and restart the device which will be automatically updated. DiagProg4 can be updated using dedicated software - DiagProg4 Manager. 14 MAINTENANCE MAINTENANCE enables remote maintenance of the device in order to ensure optimal technical parameters. Once MAINTANANCE option is selected device will automatically run microsdhc card test and will synchronize files with Elprosys server. Before you start make sure to: - insert microsdhc card - connect DP4 to WIFI network (Internet) File synchronisation can be completed using dedicated software - DiagProg4 Manager. 14
15 DISPLAY FIRMWARE UPDATE Display firmware update is downloaded automatically. User has to select from DP4 menu: SETUP OTHER SETTINGS TFT Update Estimated installation time : around 1 minute IMPORTANT: Do not turn off power supply before finishing update. 16 RESTART DIAGPROG4 If the device screen does not respond to touch, it is possible to restart it to restore its efficiency. Press and hold buttons - up and - cancel for at least 3 seconds to restart DiagProg4 device. 15
17 DIAGPROG4 MANAGER DIAGPROG4 MANAGER PC tool DIAGPROG4 MANAGER connects DiagProg4 with PC, allowing data synchronisation between devices. Software used to manage device using PC. DiagProg4 connection with PC: It is required to use mini USB cable supplied by manufacturer in order to connect DiagProg4 with PC. DiagProg4 should be connected to an additional power source. Software update Use this option to download latest update and activations from Elprosys server. File synchronization Use this option to download necessary data files (BSI, Flash, etc.) from Elprosys server Technical support MicroSD card manager Use this option to send data - like LOG file, activation status etc. required to seek technical support Use this option to view memory card data Info about DiagProg4 Info about DiagProg4 Manager Use this option to view device details Use this option to view information about DiagProg4 Manager 16
System requirements: Operating system: Windows Vista, Windows 7, Windows 8, Windows 10. RAM: 1 GB (Recommended) Free disk space: At least 2 GB (Recommended) Software requirements:.net Framework 4.5 or above 18 DESCRIPTIVE MENU Some DiagProg4 functions will show additional hints. When a position is selected from the menu device will display additional descriptive menu. In order to display hint select a position from the menu, press it and hold it. 17
RECORD OF CHANGES Date Author Changes 03.03.2016 Czupryna Sylwester Adding LEGAL RESERVATIONS and AGREEMENT OF USE 03.03.2016 Czupryna Sylwester Software number (SN) is displayed on the main screen. 03.03.2016 Czupryna Sylwester New DIAG icon replacing VIN icon on the main screen 03.03.2016 Czupryna Sylwester Change in SETUP MENU adding new positions: - MAINTENANCE - OBDII/VOLTAGE TEST SETTINGS 03.03.2016 Czupryna Sylwester Change in SUBMENU INFORMATION adding new positions: - CONTROL NUMBER - AGREEMENT OF USE - DP3 LICENSES IMPORT - OPEN-SOURCE LICENSE 03.03.2016 Czupryna Sylwester Change in TOOLS MENU adding new positions: - SENDING LOG FILE - RESTART DIAGPROG4 03.03.2016 Czupryna Sylwester Adding description for option: SENDING LOG FILE manually 03.03.2016 Czupryna Sylwester Adding description for option: MAINTANANCE 03.03.2016 Czupryna Sylwester Adding description for option: RESTART DIAGPROG4 03.03.2016 Czupryna Sylwester Adding description for option: DESCRIPTIVE MENU 03.04.2017 Czupryna Sylwester Change in TOOLS MENU adding new positions: - DOWNLOAD UPDATE/ ACTIVATION - SUPPORT SCRIPT - UDS COMMUNICATION CONTROL 03.04.2017 Czupryna Sylwester Hardware version is displayed on the main screen. 03.04.2017 Czupryna Sylwester Adding additional language: Brazilian 03.04.2017 Czupryna Sylwester Adding DISPLAY FIRMWARE UPDATE 03.04.2017 Czupryna Sylwester Adding DIAGPROG4 MANAGER PC tool 18