Product information UK 1 12 V plug 2 Microphone connection 3 Link button 4 Function indicator (blue/red) 5 Call button 6 + Volume button Use Car kit Microphone Short microphone 7 - Volume button 8 Speaker 9 On/Off switch 10 Microphone holder (with double-sided adhesive tape) 11 Microphone 12 Microphone plug 1 Insert the car kit into the car cigarette lighter. The car kit can be carefully turned in the desired direction. Press the car kit firmly into the cigarette lighter. 2 Position the microphone (10+11), preferably in front of your face and not too close to the car kit (to prevent an echo). Short microphone: easier to use, but the separate microphone has a better sound quality. Insert the microphone plug (12) into the connection (2). 1
3 Turn the car kit on using the On/Off switch (9). First use -> Step 4 Normal use -> Step 8 4 Once only (steps 4-7): Activate the pairing mode: press the Link button (3) for 7 seconds until the red indicator (4) flashes continuously (4 times per second). 5 To make a telephone call: Activate Bluetooth and search for Bluetooth devices. (The red indicator on the car kit must still be flashing in order for it to be found.) 6 Bluetooth device(s) found: Select Trust HS-8100. 2
7 Pin code = 1234 It may be possible to enter or alter the name of the car kit. Press Connect. Good connection: the red indicator will stop flashing. Go to step 9. UK 8 For normal use: after turning the car kit on (step 3), press the Link button (3) for 3 seconds -> high-low tone. A connection will be created between the telephone and the car kit. 9 Answer or end incoming call: Press the Call button quickly. 10 Press the + button and the - button to adjust the volume. Other functions: see the table. 3
Button functions and indicators (The numbers between brackets refer to the product information diagrams.) Action Button Indicator (4) Speaker (8) Turn on On/Off (9) -> On Blue on - Make BT discoverable and pair the device. Link (3) Press for 7 After 3 sec: flashes red. After 7 sec: flashes red 4 times per sec. After 3 sec: Low + high tone After successfully pairing: flashes red 1-3 times in 3 Disconnect BT connection Link (3) Press for 3 Stops flashing red. High + low tone Make BT connection Link (3) Press for 3 Flashes red 1-3 times in 3 Low + high tone Answer incoming call Call (5)** Press quickly. Ring tone -> answer call Decrease the volume - Volume (7) Quieter Increase the volume + Volume (6) Louder To end a telephone call: Call (5)** Press quickly. Tone Turn off On/Off (9) -> Off Blue off. - Other functions* Accept call waiting Call (5) Press quickly. Tone Refuse call waiting Call (5)** Press for 3 Ring tone -> - Transfer call to telephone Call (5)** Press for 3 Tone Transfer call from telephone Call (5) ** Press for 2 Tone Voice dialling task for the Call (5) ** Press quickly. Tone telephone Redial Call (5) ** Press for 3 Tone * The telephone must support the function. ** The call button only works if there is a Bluetooth connection between the telephone and the car kit. 4
NOTE! Pairing and use The car kit will ONLY work if the Bluetooth (BT) connection has been paired correctly. The car kit can only be used with BT devices which support the Headset Protocol (HP) or the HandsFree Protocol (HFP). The pairing mode only remains active for 2-3 minutes. If necessary, reactivate it. After a successful BT connection, it will not be necessary to pair the devices again, even after they have been turned off. However, if one of the devices has been paired with another, similar, BT device, they will usually have to be paired again. The method of pairing and the use of BT can differ for different devices. See the instruction manual provided with your other BT device for the correct method. Some telephones do not support the functions where the Call button is pressed for 3 Option for transferring the call to the telephone and answering the call: - Disconnect the BT connection using the Link button. - Accept the call by reactivating the BT connection by pressing the Link button and then the Call button. The original ring tone of the telephone can only be heard via this car kit if it is a polyphonic ring tone and the telephone supports the transfer of this ring tone to a BT device. If not, you will hear a standard ring tone via the car kit. Some telephones are not able to activate the BT connection immediately once BT pairing has been activated. In that case, you will not hear the telephone ring via the car kit. Solution: press the Call button quickly after activating BT pairing. With some telephones, the Call button must be pressed for 2 sec. to accept a call (e.g. Sony Ericsson P800/900). Some telephones are produced without optimal BT support. If you have a problem, check whether the telephone has the most up-to-date BT version (firmware). Contact the telephone manufacturer for more information. An up-to-date list of telephones that can be used with this car kit is available at: HThttp://www.trust.com/14271/compatibilityTH Turn the radio down or off during a telephone call. Make sure the car kit does not affect your ability to drive the car. The PIN code (1234) cannot be changed. Bad wireless connection There are metal objects close to or between the car kit and the other BT device. The other BT device has a smaller range (e.g. BT class 3: max. 1 metre). There is another wireless device close by (such as a wireless video or wireless network). Go to www.trust.com/14271 for up-to-date FAQs, instruction manuals and more information on Bluetooth. 5 UK
Basic specifications 12 V DC, 130 ma (standby), max. 550 ma (active) Only to be used in temperatures -10 C ~ 50 C, humidity 10 ~ 90% Safety instructions Never open or repair the device yourself. Do not use this device near water or other liquids. Do not use this device in a damp environment. This device meets the essential requirements and other relevant conditions of the applicable European directives. The Declaration of Conformity (DoC) is available at www.trust.com/14271/ce. Wireless This wireless Bluetooth device works at a frequency of 2.4 GHz. It meets the essential requirements and other relevant conditions of R&TTE Directive 1999/5/EC. It is a Class 1 wireless device and may be used in all EU countries. See www.trust.com/14271 for an up-to-date list of countries where the use of this product is permitted. (Note: this class indication is not the BT class). There may be restrictions for the use of this device outside of the EU. If this device is used outside of the EU, check whether this device meets the local regulations. Frequency: 2.4 ~ -2,483 GHz. Bandwidth: approx. 1 MHz, Power: 1 mw. Nowadays, there are an increasing number of wireless products (video, audio, computer, etc.) which work in the same frequency range as this device. It may, therefore, be possible that the functionality of this device is limited by or is limiting for other wireless devices. This can only be avoided by paying attention to the distance between devices and, where possible, by changing the channels of the other devices. Be careful when using wireless devices if you have a pacemaker or are dependent on other life-saving, sensitive electronic equipment, because this product transmits radio signals. Warranty & copyright This device has a two-year product warranty which is valid from the date of purchase. Go to HTwww.trust.com/warrantyTH for more information. It is forbidden to reproduce any part of this instruction manual without the permission of Trust International B.V. 6