Thank You for purchasing our firmware. This guide aims to guide you one step at a time to mod your Seagate Wireless Plus(W+) Note that this documentation is written based on the mod version 4.0 on the Wireless Plus. If you are currently on Version 2.0.0.055 or Version 2.1.0.014 of W+ Firmware, Proceed to upgrade to Version 2.2.0.005 as indicated in Step 1. Even if you are already on Version 2.2.0.005, please proceed to Step 1 again. Step 1 : W+ : Download the Seagate Wireless Plus Firmware 2.2.0.005. This can be obtained via our site. http://hackseagatesatellite.com/firmware/wirelessplusfirmware220005.iso. (MD5 : 60472f22cce320e80dd247367c6a8159) The downloaded filename is named as seagate_wirelessplus_2.2.0.005.bin after you extract it from the ISO file. Note for Mac Users : Safari tends to be too smart in trying to open safe files. Filenames ending with.bin are deemed to be safe files by Safari. If you use Safari to download the firmware, you will noticed that your downloaded file becomes a folder. To resolve this issue, please make sure you go to Safari Preferences and uncheck Open safe files after downloading.
Step 2 : Connect your Wireless Plus via USB to your computer W+ : Copy the file, seagate_wirelessplus_2.2.0.005.bin into the root directory of your Wireless Plus. Do not rename the file or putting this file into any folders. Note : If you have more than 1 partition, please put this file onto the 1st partition instead of any other partitions. Step 3 : Safely eject your Wireless Plus from your computer. Detach the USB Cable and Connector COMPLETELY. This would mean that you would be able to close the cover on the Wireless Plus. Step 4 : Power On the Wireless Plus and wait for 5 minutes. Yes. 5 entire minutes. Step 5 : Reset the Wireless Plus by poking the reset hole once located at the bottom of the Wireless Plus.
Step 6 : Scan for the Wireless Plus. You should now be able to use your PC / Mac to scan for Wireless. If you have successfully reset your Wireless Plus, you should find its name known as Wireless Plus XXX where XXX is the last 3 digits of your Wireless Plus Serial Number. Step 7 : Shutdown Wireless Plus. Reconnect the Wireless Plus to your PC / Mac via USB. Step 8 : Download our mod firmware. The link to the firmware file is provided in the forum located on http://hackseagatesatellite.com/privateforum/viewforum.php?f=64 Step 9 : Perform an MD5 checksum on our mod firmware downloaded. This is to ensure that you are having the complete package from our site. To perform a MD5 checksum : Mac Users : Launch Terminal (Found in Applications, Utilities). At the command prompt, type md5 filename. TIPS : Instead of typing the entire path of our download, you can simply drag and drop the file into the terminal window after you type md5 command. Here s an example of how the flow is : a) Launch Terminal b) Type md5 follow by a space c) Drag the downloaded mod files into the window followed by hitting the return/enter key d) The md5 checksum result will then be displayed.
Windows Users : There are many MD5 checksum software for Windows. The example that we are going to use is from winmd5.com. Use the software and verify the download file against the MD5 string provided on our forum page. Step 10 : Mount the ISO File. By now, you would have downloaded our firmware based on the link on the forum. This downloaded file is a ISO file. For Mac Users, it handles it natively. Simply Double Click on the ISO file to mount it. For Windows, you will need an ISO mounting software to mount this ISO file into a volume. The example used here is from magiciso.com.
Step 11 : Copy our mod firmware files INTO the root directory of the Wireless Plus. In the volume, there are 2 main files. run.sh and seagate_mod.tar.gz. These 2 main files needs to be copied to the root directory of the Wireless Plus. Figure showing the mounted ISO Volume Figure showing the copying of the files into the W+ Figure showing the W+ Volume with the mod files copied
Step 12 : Safely eject your Wireless Plus from your computer. Detach the USB Cable and Connector COMPLETELY. This would mean that you would be able to close the cover on the Wireless Plus. Step 13 : Power On the Wireless Plus. Step 14 : Connect to your Wireless Plus Network on your PC or Mac via WiFi Step 15 : Launch Terminal (Mac) or Command Prompt (Win) Simply go to Terminal from within your Utilities Folder. Launch Terminal. Simply go to Command Prompt by typing cmd in Start, Run.
Step 16 : Establish a Telnet Session into your Wireless Plus. Telnet command lines are universal. There is no difference between a Mac or PC or anything else. Command to type is telnet 172.25.0.1 When prompted for login, use root When prompted for password use goflex **Note that there will not be any cursor feedback or even *** appearing when you type in the password. This is the nature of Telnet. Just type the password the press enter. Step 17 : Navigate to the setup directory. Command to type is cd /static/data/1 Note : there is a space after cd static is all in small caps Data starts with Capital D 1 is numeric 1. Not L or i If you are doing it correctly, you should see /media/sda1 as indicated in the diagram below.
Step 18 : Check if the mod firmware setup files are in place. Perform a directory listings to see if you can see run.sh and seagate_mod.tar.gz are present. Command line to run is ls It s LS in small caps Step 19 : Perform the modification by executing run.sh Command line to type is./run.sh then press enter Note that there is no space at all. You will be prompted to say y and press enter during the installation. Step 20 : System reboot will automatically happen after the mod is completed. Wait for 5 minutes.
Step 21 : Join the new WiFi Network after reboot is completed. For Wireless Plus Users, the SSID is plus Default password for is 1234567890 Some users may get an error while trying to join plus for the first time. You simply power off the unit completely, wait for 30 seconds before powering up again. Step 22 : Launch our interface. Use Safari or Chrome browser and point to plus.local The interface should just appear.
TROUBLESHOOTING SECTION : Step 1 : Q : The Seagate Firmware file downloaded appears to be a folder and not a file. A : Safari has unzip the bin file for you as it deemed it as a safe file. Uncheck the Open Safe files option in Safari Preferences as indicated in Step 1. Step 2 : Q : Which is my first partition? A : If you are unsure, you should keep it as 1 single partition. In Disk Utility (Mac) or Disk Management(Win), the first partition is usually on top (in mac) or left (in windows). Step 3 : Q : Must I really remove the USM Connector? A : YES The USM (Universal Storage Module) from Seagate prevents your Wireless to start on your Wireless Plus. Seagate used the connector to cut off the WiFi. It s a fast and easy way to do so rather than a switch. If you don t believe us, try using the W+ and then plug in the connector. Your WiFi drive is disconnected. Step 4 : Q : Must I really wait for 5 minutes. A : YES. Please do so. Be patient. It is only 5 minutes. Seagate documents it down as 3 minutes but we are the guys who are more careful. Your 3 minutes may be only 2+ minutes based on the system clock. Step 5 : Q : How do I know if I have reset my Wireless Plus? A :First, you should feel a depression when you poke it once. Secondly, Step 6 will prove that you did it correctly. Step 6 : Q : I can t find the default WiFI Name. A1 : On the Macs, they tend to cache the previously scan wifi network. Turn off WiFi and scan again. A2 : Did you poke the reset hole? Q : I can still see my previous network name : A : On the Macs, they tend to cache the previously scan wifi network. Turn off WiFi and scan again. PCs might get this issue as well. Turn off WiFi on your PC / Mac and Scan again. Step 7 : Q : How do I know if the unit is powered off. A : On the W+. the power off seemed faster. But You really need to make sure the drive is no longer spinning. You can feel the drive spinning if you have not power it down. Step 8 : Q : The system told me that I don t have permission to the forum. A : The administrator has not granted access for you. Contact team@hackseagatesatellite.com for access. Provide your email address where payment is made and your username.
Step 9 : Q : My md5 checksum fail. A : Your downloaded file is incomplete. Please do not use it. Download the file again until your md5 checksum matches. Step 10 : Q : The mounting of the ISO file failed. A : The ISO file is corrupted. Please make sure you perform a md5 checksum on it as instructed on step 9. Step 11 : Q : I cannot copy the 2 files into the W+ A : This error typically affects only the Mac Users. All Macs are only about to read NTFS partition which is what your W+ is formatted as default. You should installed the Paragon NTFS Driver provided by Seagate. You can download the seagate provided version that works only on Seagate Drives @ http://www.seagate.com/support/external-hard-drives/ desktop-hard-drives/backup-plus-desk/ntfs-driver-for-mac-os-master-dl/ If you would like all NTFS formatted drives to be writable on your Mac, we strongly recommend Paragon NTFS Driver available from Paragon Software @ http:// www.paragon-software.com/home/ntfs-mac/ Step 12 : Same reason why in Step 3 Step 13 : Should not have any issues powering up your unit. Make sure there s enough power. Plug in the DC USB Cable and NOT the USB SATA Data to charge. Step 14 : Hey. It worked in Step 6 didn t it? Use the same troubleshooting tips in Step 6. Step 15 : Terminal is built into Mac. Command Prompt is built into Windows. You should not have too much of a hard time locating them. For Mac, You can go to Applications, Utilities and find Terminal.app For Windows, you can go to Start, All Programs, Accessories, Command Prompt Step 16 : Q : In my windows command line, it tells me that command not recognized when i type telnet. A : Microsoft remove telnet as part of the standard installation since Windows 7. You will need to enable it again. Check out this article by Microsoft on how to enable it back. http://social.technet.microsoft.com/wiki/contents/articles/910.how-to-enable-telnet-client-inwindows-7.aspx Q: I have telnet installed but it says cannot connect to 172.25.0.1 A : Have you connected to your Wireless Plus network? If your computer has both wired and wireless connection, please unplug your Wired connection and try again.
Q : I am connected to the Wireless Network. But telnet still says cannot be connected to 172.25.0.1 A : Can you try to ping 172.25.0.1 to see if you are able to see the unit? Launch your web browser and it will automatically redirect you to the original seagate firmware page. Go to settings and select restore factory settings. Q : My Wireless Plus IP address is not 172.25.0.1 A : Are you sure you are using the Wireless Plus? The 1st version of the Wireless Plus already used 172 range of IP Address. Step 17 : Q : I get an error that I am unable to go to sda1 A : For Mac Users, it is likely that you have formatted the drive as NTFS but the partition scheme has been changed to GUID. Please format it back to NTFS with partition scheme of Master Boot Record. If you are not seeing that you are in sda1, we highly recommend that you reformat your GoFlex Satellite into 1 single partition in NTFS and Master Boot Record Partition Scheme. Step 18 : Q : I am in sda1 and I performed the ls command. But I cannot locate the 2 mod files. A : You have placed the mod in the wrong partition. Step 19 : Q : It says command not found. A : Did you check that you have those 2 files in Step 18? Q : It tells me the mod cannot be proceed. A :Looks like you did not restore your Wireless Plus back to factory default firmware. When our firmware detects and irregularity in your firmware, we will not proceed as it will brick your unit if you forced it to do so. Q : It tells me timeout. A : You have to press y and then enter within 15 seconds when it starts prompting you. Step 20 : Q : System did not reboot. A : It should reboot itself and your telnet session would have ended. If not, can you copy all the text that you see in the telnet session to team@hackseagatesatellite.com for further diagnostics on whether your mod is complete. Step 21 : Q : I can see plus as SSID and there is no indication that it protected with a password. When I try to join, it fails. A : Please wait patiently for 5 minutes after our mod is completed. As the system reboots, we are making changes to it so that your W+ will have either plus as the SSID and there is a default password of 1234567890. Please be patient. Step 22 : Q : Can I use IE or Firefox A : Unfortunately, we will only support Safari and Chrome since it s webkit based browser. Q : I can access the interface but I can t see any of my files.
A : There are also many files that we have placed at the root directory of your Wireless Plus during the mod process. In order to ensure that you do not delete some files accidentally, we have created a default Data folder for you to place all of your data inside. This will help keep it neat. If you feel that you still want the access to your root folder, simple go to our interface page, go to settings, system, under Web Server Setup, remove the Data from the Root Web Browsing Directory as shown. We try our best to put down as much in detail as possible in this documentation. We will try to update this documentation as we gather more feedback from you as our user. Please send all feedback to team@hackseagatesatellite.com Thanks again for purchasing our mod firmware. We really appreciate it. Team Hack Seagate Satellite... And Now the Wireless Plus too...